QSC Audio 522uaの取扱説明書

28ページ 1.62 mb
ダウンロード

ページに移動 of 28

Summary
  • QSC Audio 522ua - page 1

    TD-000198- 00 rev .A *TD-000198-00* RA VE 522ua 8x8 CobraNet Enabled Signal Processor Hardware Manual ...

  • QSC Audio 522ua - page 2

    2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol wit hin an equilateral tri angle is intended to al ert the user to the presence of uninsula ted “dangerous” voltage within the product’ s enclosure t hat may be of sufficien t magnitude to constit ute a risk of electri c shock to humans. The ...

  • QSC Audio 522ua - page 3

    3 Introduction 1- Power indicator 2- Diagnostic indicator 3- Network status indicators 4- Signal presence/clip indicators 5- Multi-function push buttons 6- Display 7- Rotary select/accept knob 8- Safe Mode switch (recessed) 9- Analog outputs 10- Mic/line inputs 11- Relay outputs 12- Logic outputs 13- Omni inputs 14- RS-232 port 15- Network status i ...

  • QSC Audio 522ua - page 4

    4 does not change regardless of the DSP configuration, unless the configuration intentionally adds more delay . The RA VE 522ua also supports the new optional low-latency CobraNet feature that provi des transport at only 2.66 milli- seconds delay . Thus the delay from analog to analog across the network can be less than 6 milliseconds, fast enough ...

  • QSC Audio 522ua - page 5

    5 Introduction - Networking the RA VE 522ua The RA VE 522ua has two RJ-45 network connection ports on the r ear panel. One port is labeled "QSControl" and supports standard 10BASE-T Ethernet. The other port is labeled "CobraNet" and supports 100BASE-TX, also k nown as "Fas t Ethernet". In the followi ng sections, we de ...

  • QSC Audio 522ua - page 6

    6 Third, the RA VE 522ua and QSControl.net system are targeted at network switch deployments. The consumer costs of Ethernet switches have continued to fall over the last several years and are now comparable with repeaters on a per port basis. In addit ion, the sophistication and scalability of network switches make them i deal for new installation ...

  • QSC Audio 522ua - page 7

    7 Example #2 - CobraNet X-over mode: This is the simplest connection you can make between the RA VE 522ua and any of the other RAVE/BASI S models. Use a CA T -5 cross- over cable connected between the CobraNet ports of each unit. No network s witch is required. This connection allows audio to pa ss between the two RA VE/BASIS units over CobraNet. C ...

  • QSC Audio 522ua - page 8

    8 Example #3 - Singl e Wire Interface: Here all QSControl.net and CobraNet traffic shares the sa me single CA T -5 cable between the RA VE 522ua and an unmanaged Ethernet switch. The QSControl.net system manages traffic flow efficiently and reliably so that all audio and control data is delivered to its appropriate destination anywhere on the netwo ...

  • QSC Audio 522ua - page 9

    9 Example #4 - T wo-Wire Interf ace (shared network hardware): This example illustrates the T wo-Wire Interface with a managed Et hernet switch. The switch is configured with multiple virtual local area networks (VLANs). Ethernet deliveries can only reach des tination ports belonging to the same VLAN from which it was sourced. The figure shows a se ...

  • QSC Audio 522ua - page 10

    10 Example #5 - T wo-Wire Interf ace (separate netwo rk hardware): Example #5 is conceptually similar to example #4. The differenc e here is that separate networks are created by providing each l ocal area network (LAN) with its own network switch. Therefore, tra ffic segmentation is physical rather than logical. Ex ample #5 also pro- vides an addi ...

  • QSC Audio 522ua - page 11

    11 Unpacking There are no special unpacking precautions. However , it is recommended you keep the original packing material for reuse in the rare event that service be required. If service is required and the or iginal packing material is not available, ensure that the unit is adequately protected for shipment (strong box of appr opriate size, suff ...

  • QSC Audio 522ua - page 12

    12 Computer Requirements & Software Installation Installing QSControl.net is easy . All you need to do is choose th e folder where the program is to be stored (the default settin g is accept- able for most applications). We recommend your syste m meet the following minimum requirements: 1- IBM PC compatible computer with a Pentium 4 processor . ...

  • QSC Audio 522ua - page 13

    13 General Information & Configuration Memories Network The network should be operable and QSControl.net software s hould be installed/running on the system controller computer . CobraNet Connec tion Loss If you are operating with a valid CobraNet network, and the c onnection to the network is disrupted, audio will mom entarily mute , allow- in ...

  • QSC Audio 522ua - page 14

    14 Connections AC Power Cord Insert the molded receptacle of the AC power cord into th e AC power inlet on the back of the RA VE 522ua. Plug the AC line connector into the AC out- let. The power supply will accept from 100 to 240 V olts AC, 47 to 440 Hertz, without any changes. If a different type of IEC power cord is required than the one supplied ...

  • QSC Audio 522ua - page 15

    15 Relay Out T wo sets of relay contacts are provided, RELA Y OUT 1 and RELA Y OUT 2. Contacts are floating and rated for 30VDC, 1A. There is one common terminal, one normally-closed contact terminal and one normally-open contact terminal. These are labeled as C, NC and NO on the rear panel. When the relay is not energized, the C terminal is connec ...

  • QSC Audio 522ua - page 16

    16 LED Indicators (continued) QSControl and Cobra Net Network St atus (Port) Indicators- There are three LEDs on the front and rear panels labeled RX, TX and LINK. One group is for the QSControl.net network port and the other for the CobraNet network port. Their func- tions are described below . Note: Port indicators on rear panel are color coded t ...

  • QSC Audio 522ua - page 17

    17 LCD Navigation Map Left side butto ns have screen depe ndent functi ons. This read-only screen is the “out o f the box” default display after power up. Th is is the most desired informatio n when first setting up a network sys tem. Once use r moves to a differen t screen, the last screen accessed becomes the new po wer up default. Boot Scree ...

  • QSC Audio 522ua - page 18

    18 Getting Started This section outlines one of the simpler methods of getting familiar with your RA VE and the QSControl.net software. The goal of this procedure is to get your computer and the RA VE connected and communicating and the QSControl.net software installed and running . After the software is installed and running, refer to the software ...

  • QSC Audio 522ua - page 19

    19 Getting Started (continued) 17- Select Device , Add Device , from the menu. A new window will open prompting you to name the device. Name it logically , such as RA VE 1, or similar . Select the Device T ype and select RAVE 522ua. At the Password prompt, enter “qsc” (lower case, no quotat ion marks). This is the device password, separate from ...

  • QSC Audio 522ua - page 20

    20 Operation QSControl Port The QSControl port operates on a 10BaseT Ethernet network. This por t is one of the primary means for connecting QSControl.net to the RA VE. The port may connect directly to a PC's 10BaseT or 10/100 ( auto-sensing or auto-negotiating) network interfac e card using a crossover cable. Data from the QSControl port may ...

  • QSC Audio 522ua - page 21

    21 Utility/Diagnostic Functions Safe Mode Switch Location of Safe Mode switch: The front panel has a small access hole on the left side, just left of the Power indicator . It is not labeled to help prevent accidental use. The Safe Mode switch can be operated by using a paperclip (or similar item) inserted in to the access hole and pushing. Safe Mod ...

  • QSC Audio 522ua - page 22

    22 Utility/Diagnostic Fu nctions (continued) RS-232 Communications Procedure: 1) Connect the RS-232 port of the RA VE 522ua to an unused serial port (COM po rt) of a PC using a normal (straight-through) serial cable. 2) Open the HyperT erm inal program. This program is usually started by clicking the Windows Start icon, selecting Programs , then Ac ...

  • QSC Audio 522ua - page 23

    23 Utility/Diagnostic Fu nctions (continued) T elnet Access The RS-232 features can also be accessed via T elnet. The Micros oft T elnet application is a Windows program. Consult Windows documentation for T elnet information. Basic procedure for opening a T elnet session: 1 - T o open the T elnet session- Click ST ART , select RUN , type “T elnet ...

  • QSC Audio 522ua - page 24

    24 Preliminary Specification IN OUT THRU Dynamic Range (A ES-17, -60dB Method, all sensit ivities) unweighted >110dB >112dB >108dB A weighted >113dB >115dB >111dB Distortion (20Hz-20 KHz, all sen sitivities) Gain= 0 - 30dB <0.008% THD+N <0.009% THD+N <0.009% THD+N Gain >30dB <0.05% THD+N <0.009% THD+N <0.05% T ...

  • QSC Audio 522ua - page 25

    25 Preliminary Specification Relay Outputs 2 discrete floating relay switch outputs Connector T ype 3-pin "Phoenix Style" (a.k.a . "Euro Style") detachable terminal blocks Configuration Electromechanical Relay Pinout 1:NC 2:NO 3: COM Switching Capacity (nom) 1A 30VDC Logic Outputs 4 discrete outputs Connector T ype 2-pin "P ...

  • QSC Audio 522ua - page 26

    26 Dimensions ...

  • QSC Audio 522ua - page 27

    ...

  • QSC Audio 522ua - page 28

    QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2005 “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T elephone Numbers: Main Number (714) 754-6 ...

メーカー QSC Audio カテゴリー Baby Monitor

QSC Audio 522uaのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 522uaの取扱説明書
- QSC Audioの製品カード
- パンフレット
- またはQSC Audio 522uaの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、QSC Audio 522uaの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、QSC Audio 522uaの取り付け説明書、サービスマニュアル、簡易説明書、またはQSC Audio 522uaのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、QSC Audio 522uaの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

QSC Audio 522uaデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQSC Audio 522uaを使用するのを助ける技術的文書のことです。説明書は通常、全てのQSC Audio 522uaユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

QSC Audioの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. QSC Audio 522uaの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQSC Audio 522uaの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。QSC Audio 522uaに関してこのドキュメントで見つけることができる全てのヒントの目次
3. QSC Audio 522uaデバイスの基本機能を使うにあたってのヒント。 QSC Audio 522uaのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。QSC Audio 522uaに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQSC Audio 522uaのメーカー/サービスへの連絡先に関する情報。

QSC Audio 522uaについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもQSC Audio 522uaの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQSC Audio 522uaで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)