Delta Electronics VFD-XXXEの取扱説明書

36ページ 1.03 mb
ダウンロード

ページに移動 of 36

Summary
  • Delta Electronics VFD-XXXE - page 1

    English- 1 Preface Thank you for choosing DELTA’s high-performance VFD-E Serie s. The VFD-E Series is manufactured with high-quali ty components and ma terials and incorporate th e latest microprocesso r technology av ailable.  Getting Started This quick start w ill be helpful in the installation and parameter setting of the AC motor driv es. ...

  • Delta Electronics VFD-XXXE - page 2

    English- 2 Specifications Voltage Class 115V Class Model Number VFD-XXXE 002 004 007 Max. Appli cable Motor Output ( kW) 0.2 0.4 0.75 Max. Appli cable Motor Outp ut (hp) 0.25 0.5 1.0 Rated Output Cap acity (kV A) 0.6 1.0 1.6 Rated Output Cur rent (A) 1.6 2.5 4.2 Maximum Outpu t Voltage (V) 3-Phase Propor tional to Tw ice the Input Volt age Output F ...

  • Delta Electronics VFD-XXXE - page 3

    English- 3 General Specifications Control System SPWM(Sinusoidal Pulse Wid th Modulation) c ontrol (V/f or sensorless v ector control) Frequency Setting R esolution 0.01Hz Output Frequency Resolution 0.01Hz T orque Characteri stics Including the aut o-torque/auto-s lip compensa tion; starting torque can be 150% at 3.0Hz Overload Endur ance 150% of ...

  • Delta Electronics VFD-XXXE - page 4

    English- 4 Storage/ Transportati on Temperature -20 o C to 60 o C Ambient Humidi ty Below 90% RH (no n-condensing) Vibration 9.80665m/s 2 (1G) less than 20Hz , 5.88m/s2 (0.6G) at 20 to 50Hz Approvals Basic Wiring Diagram Users must connect wiring a ccording to the follow ing circuit diagram shown below. AV I ACI ACM + 4~2 0m A +10V 5K 3 2 1 Power s ...

  • Delta Electronics VFD-XXXE - page 5

    English- 5 + - Pl ease us e br ake unit and/or br ake r esi sto r dep endi ng on ty pe and a ppl i cat i o n B ra k e un it (o pti on al ) BU E BR brak e res is t or (opt i o nal) Fi gu re 1 fo r m od el s of VF D-E S e r i es VFD 002E11 A /21A/ 23A, VFD00 4E11A /21A/2 3A/43A , V F D 007E21 A/ 23A/43 A, VFD 015E23A/43 A, V F D002E1 1C/ 21C/23C , VF ...

  • Delta Electronics VFD-XXXE - page 6

    English- 6 C. PNP mode without external power D. PNP mode with external power Sw1 Facto ry setting NPN PNP Sw1 Facto ry setting NPN PNP 24 Vdc - + Figure 5 RJ-45 Pins Definiti on for VFD*E*C Models PIN Signal Description 1 CAN_H CAN_H bus line (dominant high) 2 CAN_L CAN_L bus line (dominant low) 3 CAN_GND Ground / 0V /V- 4 SG+ 485 communication 5 ...

  • Delta Electronics VFD-XXXE - page 7

    English- 7 Operation Steps of t he Digital Ke ypad To s h i f t d a t a Setting PLC Mode Se tting Mode Se tting directi on (When operation s ource is digital keypad) START GO ST AR T enter PLC2 mode enter PLC1 mode NOT E : In the param eter setti ng mode, you can pr ess to ret urn the sel ec tin g mode . NOT E: In the selection mode, press to set ...

  • Delta Electronics VFD-XXXE - page 8

    English- 8 Power Terminals and Control Terminals Frame A Frame B Frame C Frame Power Term inals Torque Wire Wire Ty pe R/L1, S/L2, T/L3 A U/T1, V/T2, W/ T3, 14kgf-cm (12in-lbf) 12-14 AWG. (3.3-2.1mm 2 ) Copper only, 75 o C R/L1, S/L2, T/L3 U/T1, V/T2, W/ T3 B +/B1, B2, -, 18kgf-cm (15.6in-lbf) 8-18 AWG. (8.4-0.8mm 2 ) Copper only, 75 o C R/L1, S/L2 ...

  • Delta Electronics VFD-XXXE - page 9

    English- 9 The Specification for the Control Terminals RS-485 port 1 0 V MI1 MI2 M I3 MI4 MI5 MI6 DCM 24V DCM A CM AV I A C I AFM MCM MO1 RA RB RC The position of t he cont rol termina ls Te r m i n a l s 2 Te r m i n a l s 1 Frame Control Terminals Tor que Wire Terminals 1 5 kgf-cm (4.4 in-lbf) 12-24 AWG (3.3-0.2mm 2 ) A, B, C Terminals 2 2 kgf-cm ...

  • Delta Electronics VFD-XXXE - page 10

    English- 10 Terminal Symbol Terminal Function Factory Settings (N PN mode) ON: Connect to DCM MO1 Multi-function Output 1 (Photocoupler) Maximum 48VDC, 50mA Refer to Pr.03.01 for programming MO1- DCM Mo 1 MCM Ma x: 48Vdc 50 mA intern al circu it MCM Multi-function output common C ommon for Multi-function Outputs +10V Potentiometer power supply +10V ...

  • Delta Electronics VFD-XXXE - page 11

    English- 11 Pr. Explanation Settings Factory Setting NOTE 00.01 Rated Current Display of the AC motor drive Read-only #.# 00.02 Parameter Reset 0: Parameter can b e read/written 1: All parameters ar e read only 6: Clear PLC program (NOT for VFD*E*C models) 9: All paramete rs are reset to factory s ettings (50Hz, 230V/400V or 220V /380V depends on P ...

  • Delta Electronics VFD-XXXE - page 12

    English- 12 Pr. Explanation Settings Factory Setting NOTE 00.12 50Hz Base Vol tage Selection 0: 230V/400V 1: 220V/380V 0 Group 1 Basic Parameters 01.00 Maximum Output Frequency (Fmax) 50.00 to 600.0 Hz 60.00 01.01 Maximum Voltage Frequency (Fbase) (Motor 0) 0.10 to 600.0 H z 60.00 220.0 01.02 Maximum Output Voltage (Vmax) (Motor 0) 115V/230V series ...

  • Delta Electronics VFD-XXXE - page 13

    English- 13 Pr. Explanation Settings Factory Setting NOTE 01.21 Delay Time at 10Hz for Simple Position 0.00 to 600.00 sec 0.00 01.22 Delay Time at 20Hz for Simple Position 0.00 to 600.00 sec 0.00 01.23 Delay Time at 30Hz for Simple Position 0.00 to 600.00 sec 0.00 01.24 Delay Time at 40Hz for Simple Position 0.00 to 600.00 sec 0.00 01.25 Delay Time ...

  • Delta Electronics VFD-XXXE - page 14

    English- 14 Pr. Explanation Settings Factory Setting NOTE 01.40 Mid-Point Frequency (Fmid) (Motor 3) 0.10 to 600.0 H z 1.50 115V/230V series: 0.1V to 255.0V 10.0 01.41 Mid-Point Voltage (Vmid) (Motor 3) 460V series: 0.1V to 510 .0V 20.0 01.42 Minimum Output Frequency (Fmin) (Motor 3) 0.10 to 600.0 H z 1.50 115V/230V series: 0.1V to 255.0V 10.0 01.4 ...

  • Delta Electronics VFD-XXXE - page 15

    English- 15 Pr. Explanation Settings Factory Setting NOTE 02.05 Line Start Lockout 0: Disable. Operation sta tus is not changed even if operation command source Pr .02.01 is changed. 1: Enable. Operation sta tus is not changed even if operation command source Pr .02.01 is changed. 2: Disable. Operation sta tus will change if operation command so ur ...

  • Delta Electronics VFD-XXXE - page 16

    English- 16 Pr. Explanation Settings Factory Setting NOTE 02.14 Initial Frequency Selection (for keypad & RS485/USB) 0: by Current Freq Command 1: by Zero Freq Command 2: by Frequency Display at Stop 0 02.15 Initial Frequency Setpoint (for key pad & RS485/USB) 0.00 ~ 600.0Hz 60.00 02.16 Display the Master Freq Command Source Read Only Bit0= ...

  • Delta Electronics VFD-XXXE - page 17

    English- 17 Pr. Explanation Settings Factory Setting NOTE 03.05 Terminal Count Value 0 to 9999 0 03.06 Preliminary Count Value 0 to 9999 0 03.07 EF Active When Terminal Count Value Attained 0: Terminal count v alue attained, no E F display 1: Terminal count v alue attained, EF active 0 03.08 Fan Control 0: Fan alway s ON 1: 1 minute after A C motor ...

  • Delta Electronics VFD-XXXE - page 18

    English- 18 Pr. Explanation Settings Factory Setting NOTE 04.03 Keypad Potentiometer Negative Bias, Reverse Motion Enable/Disable 0: No negative bias command 1: Negative bias: REV motion enabled 0 04.04 2-wire/3-wire Operation Control Modes 0: 2-wire: FWD/ST OP, REV/STOP 1: 2-wire: FWD/REV, RUN/STOP 2: 3-wire operation 0 1 04.05 Multi-function Inpu ...

  • Delta Electronics VFD-XXXE - page 19

    English- 19 Pr. Explanation Settings Factory Setting NOTE Bit11:MI12 0:N.O., 1: N.C. P.S.:MI1 to MI3 will be i nvalid when it i s 3- wire control. 04.10 Digital Terminal Input Debouncing Time 1 to 20 (*2ms) 1 04.11 Min AVI Voltage 0.0 to 10.0V 0.0 04.12 Min AVI Frequency 0.0 to 100.0% 0.0 04.13 Max AVI Voltage 0.0 to 10.0V 10.0 04.14 Max AVI Freque ...

  • Delta Electronics VFD-XXXE - page 20

    English- 20 Pr. Explanation Settings Factory Setting NOTE Bit8: MI9 Sta tus Bit9: MI10 Sta tus Bit1 0: MI11 Status Bit1 1: MI12 Status 04.27 Internal/External Multi-function Input Terminals Selection 0~4095 0 a 04.28 Internal Terminal Status 0~4095 0 Group 5 Multi-Step S peeds Parameters a 05.00 1st Step Speed Frequency 0.00 to 600.0 H z 0.00 a 05. ...

  • Delta Electronics VFD-XXXE - page 21

    English- 21 Pr. Explanation Settings Factory Setting NOTE 06.03 Over-Torque Detection Mode (OL2) 0: Disabled 1: Enabled during constant speed operation. After the ov er-torque is detected , keep running until OL1 o r OL occurs. 2: Enabled during constant speed operation. After the ov er-torque is detected , stop running. 3: Enabled during a ccel. A ...

  • Delta Electronics VFD-XXXE - page 22

    English- 22 Pr. Explanation Settings Factory Setting NOTE 06.1 1 Fourth Most Recen t Fault Record 06.12 Fifth Most R ecent Fault Record 27: DCBUS error (cF3.3) 28: IGBT Overheat (cF3.4) 29: Power Board O verheat (cF3.5) 30: Control Board CPU WRITE failure (cF1.1) 31: Control Board CPU WRITE failure (cF2.1) 32: ACI signal error (AErr ) 33: Reserved ...

  • Delta Electronics VFD-XXXE - page 23

    English- 23 Pr. Explanation Settings Factory Setting NOTE 07.15 Motor PTC Overheat Warning Level 0.1~10.0V 1.2 07.16 Motor PTC Overheat Reset Delta Level 0.1~5.0V 0.6 07.17 Treatment of the Motor PTC Overheat 0: Warn and RAMP to stop 1: Warn and COAST to stop 2: Warn and keep running 0 07.18 Motor Rated Current (Motor 1) 30 %FLA to 120% FLA FLA 07. ...

  • Delta Electronics VFD-XXXE - page 24

    English- 24 Pr. Explanation Settings Factory Setting NOTE 07.36 Motor Line-to-line Resistance R1 (Motor 3) 0~65535 m Ω 0 07.37 Motor Rated Slip (Motor 3) 0.00 to 20.00 Hz 3.00 07.38 Motor Pole Number (Motor 3) 2 to 10 4 Group 8 Special Parameters 08.00 DC Brake Current Level 0 to 100% 0 08.01 DC Brake Time during Start-Up 0.0 to 60.0 sec 0.0 08.02 ...

  • Delta Electronics VFD-XXXE - page 25

    English- 25 Pr. Explanation Settings Factory Setting NOTE 08.17 Auto Energy Saving 0: Disable 1: Enable 0 08.18 AVR Function 0: AVR function en able 1: AVR function disable 2: AVR function disable for decel. 3: AVR function disable for stop 0 08.19 Software Brake Level 115V / 230V series: 370 .0to 430.0V 460V series: 740.0 to 860.0 V 380.0 760.0 a ...

  • Delta Electronics VFD-XXXE - page 26

    English- 26 Pr. Explanation Settings Factory Setting NOTE a 09.08 Transmission Speed for USB Card 0: Baud rate 4800 bps 1: Baud rate 9600 bps 2: Baud rate 1920 0 bps 3: Baud rate 3840 0 bps 4: Baud rate 5760 0 bps 2 a 09.09 Communication Protocol for USB Card 0: 7,N, 2 for AS CII 1: 7,E,1 for ASC II 2: 7,O,1 for ASCII 3: 8,N,2 for RTU 4: 8,E,1 for ...

  • Delta Electronics VFD-XXXE - page 27

    English- 27 Pr. Explanation Settings Factory Setting NOTE 10.00 PID Set Point Selection 0: Disable PID operation 1: Keypad (based o n Pr.02.00) 2: 0 to +10V from AV I 3: 4 to 20m A from ACI or 0 to +10V from AVI2 4: PID set point (Pr .10.11) 0 10.01 Input Terminal for PID Feedback 0: Positiv e PID feedback from external terminal AVI (0 ~ +10VDC) 1: ...

  • Delta Electronics VFD-XXXE - page 28

    English- 28 Pr. Explanation Settings Factory Setting NOTE 11.00 Multi-function Output Terminal MO2/RA2 0 11.01 Multi-function Output Terminal MO3/RA3 0 11.02 Multi-function Output Terminal MO4/RA4 0: No function 1: AC drive operati onal 2: Master frequency attained 3: Zero speed 4: Over torque de tection 5: Base-Block (B .B.) indication 6: Low-volt ...

  • Delta Electronics VFD-XXXE - page 29

    English- 29 Pr. Explanation Settings Factory Setting NOTE 23: Quick Stop (Only for VFD*E*C models) 24: Download/execute/monitor PLC Program (PLC2) (NOT for VFD*E*C models) 25: Simple position function 26: OOB (Out of Ba lance Detection) 27: Motor selection (bit 0) 28: Motor selection (bit 1) Group 12: A nalog Input/Output Parameters for Extension C ...

  • Delta Electronics VFD-XXXE - page 30

    English- 30 Pr. Explanation Settings Factory Setting NOTE 12.18 Max. ACI3 Input Current 0.0 to 20.0mA 20.0 12.19 Max. ACI3 Scale Percentage 0.0 to 100.0% 100.0 12.20 AO1 Terminal Analog Signal Mode 0: AVO1 1: ACO1 (analog current 0 .0 to 20.0mA) 2: ACO1 (analog current 4 .0 to 20.0mA) 0 0: Analog Frequency 12.21 AO1 Analog Output Signal 1: Analog C ...

  • Delta Electronics VFD-XXXE - page 31

    English- 31 Fault Name Fault Descri ptions Corrective A ctions Low voltage The AC motor drive detects that the DC bus volta ge has fallen be low its minimu m value. 1. Check wh ether the input vo ltage falls with in the AC m otor drive ra ted in put vol tage ra nge. 2. Check whether the motor ha s sudden load. 3. Check for correct wiring of input p ...

  • Delta Electronics VFD-XXXE - page 32

    English- 32 Fault Name Fault Descri ptions Corrective A ctions Overload 2 Motor overl oad. 1. Reduce th e motor load . 2. Adjust the ov er-torque dete ction setti ng to an appropriate setting (P r.06.03 to Pr.06.05). Software protection failure Return to the factory. CC (cur rent cl amp) OV hardware error GFF hardware error OC hard w are error Retu ...

  • Delta Electronics VFD-XXXE - page 33

    English- 33 Fault Name Fault Descri ptions Corrective A ctions Auto accel/d ecel failu re 1. Check if the motor is suitable fo r operation by AC motor dri ve. 2. Check if the regenera tive energy is too larg e. 3. Load may have ch anged suddenly . U-phase erro r V-phase e rror W-phase error OV or LV Temperat ure sens or error Return to the factory. ...

  • Delta Electronics VFD-XXXE - page 34

    English- 34 Fault Name Fault Descri ptions Corrective A ctions CANopen SYNC Time out (Only for VFDxxxExxC) Check if CANope n synchr onous message is abnormal CANopen SDO Time out (Only for VFDxxxExxC) Check if command chan nels are fu ll CANopen SDO buffer overflow (Only for VFDxxxExxC) 1. Too short time between command s, please check SDO message ...

  • Delta Electronics VFD-XXXE - page 35

    English- 35 NO TE Frame A (A1): VFD002E11A/21A/23 A, VFD004E11A/21A /23A /43A, VFD007E21A/23A/43A, VFD015E23A/43A, VFD002E11C/ 21C/23C, VFD004E11 C/21C/23C/43C, VF D007E21C/23C/43 C, VFD015E23C/43C, VFD 002E11T/21T/23T, VFD 004E11T/21T/23T/43T, VFD 007E21T/23T/43T, VFD015E23T/43T Frame A (A2): VFD002E11P/21P/23 P, VFD004E11P/21P /23P /43P, VFD007E2 ...

  • Delta Electronics VFD-XXXE - page 36

    English- 36 Frame C H H1 W1 W S1 S2 D D1 D2 Unit: mm [inch] Frame W W1 H H1 D D1 D2 S1 S2 C1 130.0 [5.12] 116.0 [4.57] 260.0 [10.24] 246.5 [9.70] 169.2 [6.66] 78.5 [3.09] 8.0 [0.31] 6.5 [0.26] 5.5 [0.22] NO TE Frame C (C1): VFD055E23A/4 3A, VFD075E23A/43A, VFD110E43A/4 3C, VFD055E23C/43C, VFD075E23C/43C ...

メーカー Delta Electronics カテゴリー Network Card

Delta Electronics VFD-XXXEのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- VFD-XXXEの取扱説明書
- Delta Electronicsの製品カード
- パンフレット
- またはDelta Electronics VFD-XXXEの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta Electronics VFD-XXXEの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta Electronics VFD-XXXEの取り付け説明書、サービスマニュアル、簡易説明書、またはDelta Electronics VFD-XXXEのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta Electronics VFD-XXXEの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Delta Electronics VFD-XXXEデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta Electronics VFD-XXXEを使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta Electronics VFD-XXXEユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Delta Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta Electronics VFD-XXXEの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta Electronics VFD-XXXEの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta Electronics VFD-XXXEに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta Electronics VFD-XXXEデバイスの基本機能を使うにあたってのヒント。 Delta Electronics VFD-XXXEのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta Electronics VFD-XXXEに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta Electronics VFD-XXXEのメーカー/サービスへの連絡先に関する情報。

Delta Electronics VFD-XXXEについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta Electronics VFD-XXXEの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta Electronics VFD-XXXEで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)