Honeywell RM7800Eの取扱説明書

16ページ 0.44 mb
ダウンロード

ページに移動 of 16

Summary
  • Honeywell RM7800E - page 1

    INST ALLATION INSTRUCTIONS 66-1085-04 SIL 3 Capable RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES Relay Modules APPLICATION The Honeywell RM7800/R M7840 Relay Modules ar e microprocessor-based integrated burner control s for automatically fired gas, oil, or combination fuel single burner applications. The RM7800/RM7840 Rel ay Modules are used for UL/C ...

  • Honeywell RM7800E - page 2

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 2 WARNING Electrical Shock Hazard. Can cause ser ious injury or d eath. Disconnect the power suppl y before beginning installation. More than one power supply disconnect may be required. IMPORT ANT 1. Wiring connections for the relay modul es are unique; therefore, refer to Fig. ...

  • Honeywell RM7800E - page 3

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 3 66-1085—04 a. Do not run high voltage ignition transfo rmer wires in the same conduit with the flame detector , Data Controlbus Module™, or Remote Reset Module wiring. b. Do not route flame detector , Data Controlbus Module™, or Remote Reset Module leadwires in conduit with line volta ...

  • Honeywell RM7800E - page 4

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 4 Fig. 1. Internal block diagram of the RM7800L/RM7840L (See Fig. 2, 3, 4 or 5 for individual det ailed wiring instructions). CONFIGURATION JUMPERS MICROCOMPUTER RESET PUSHBUTTON RUN/TEST SWITCH STATUS LEDs PLUG-IN PURGE TIMER CARD SAFETY RELAY CIRCUIT POWER SUPPLY KEYBOARD DIS ...

  • Honeywell RM7800E - page 5

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 5 66-1085—04 T able 2. Rec ommended Grounding Practices. T able 3. T erminal Ra tings. . a The relay module must have an earth groun d providing a c onnecti on between the subbase a nd the control panel or the equipment. The earth ground wire must be capable of conducting th e current to bl ...

  • Honeywell RM7800E - page 6

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 6 T able 4. Combin ations for T erminals 8, 9, 10 and 21. T able 5. Explan ation of Each Combination. Mounting RM7800/RM7840 Relay Module (Fig. 5) 1. Mount the RM7800/RM7840 vertically on the Q7800 Subbase, or mount horizontally with the knife blade terminals pointing downwa rd ...

  • Honeywell RM7800E - page 7

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 7 66-1085—04 Fig. 2. Wiring subbase and sequ ence for RM7800E,L/RM7840E,L. RM7800/RM7840E,L POWER 00 OPERATING CONTROLS AND INTERLOCKS BURNER FLAME SIGNAL FIRING RATE MOTOR INITIATE (INITIAL POWERUP ONLY) POWER STANDBY POWER PREPURGE HOLD DRIVE TO HIGH FIRE PREPURGE HOLD DRIVE TO LOW FIRE P ...

  • Honeywell RM7800E - page 8

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 8 Fig. 3. Wiring subbase and sequence for RM78 00G/RM7840G . M12260B G L2 3 4 5 6 7 8 9 10 F (L1) 13 14 15 16 17 18 19 20 21 22 12 RUNNING INTERLOCKS (INC. AIR FLOW SWITCH) MASTER SWITCH LOW FIRE START SWITCH 5 SECOND IGNITION (EARLY SPARK TERMINATION) MAIN FUEL VALVE(S) BURNER ...

  • Honeywell RM7800E - page 9

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 9 66-1085—04 Fig. 4. Wiring subbase and sequen ce for RM7800M/RM7840M. M12262A G L2 3 4 5 6 7 8 9 10 F (L1) 13 14 15 16 17 18 19 20 21 22 12 MASTER SWITCH LOW FIRE START SWITCH 5 SECOND IGNITION (EARLY SPARK TERMINATION) MAIN FUEL VALVE(S) BURNER CONTROLLER/LIMITS BURNER MOTOR (BLOWER) COMM ...

  • Honeywell RM7800E - page 10

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 10 Fig. 5. RM7800/RM7840 Re lay Module exploded view. SAFETY SHUT DOWN Safety Shut down (Lockout) occurs if any of the followin g occur during the indicated period: 1. INITIA TE Peri od: a. Purge card is not installed or is removed. b. Purge card is bad. c. Configuration jumper ...

  • Honeywell RM7800E - page 11

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 11 66-1085—04 g. Lockout Interlock opens during PREPURGE (RM7840E,L). h. Ignition/pilot valve/intermitt ent pilot valve terminal is energized. i. Main valve terminal is energized. j. Internal system fault occurred. k. Purge card is removed. l. Purge card is bad. 4. PILOT FLAME EST ABLISHI N ...

  • Honeywell RM7800E - page 12

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 12 terminal 21. The RM780 0/RM7840G has an interrupted or intermittent pilot valve, terminal 21, depending on the selection of configuratio n jumper 2. The RM7800/RM78 40E,L has a fifteen-second interrupted pilot valve, terminal 21. All of the RM7800/RM7840s have a ten-second i ...

  • Honeywell RM7800E - page 13

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 13 66-1085—04 • Lockout information (Lockout, Faul t Code, Message and Sequence). The extreme right side o f the firs t line is either b lank or shows a small arrow pointing to the second line follo wed by a two-letter code (DI-Diagnostic Information, Hn-Faul t History Information, and EA ...

  • Honeywell RM7800E - page 14

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES 66-1085—0 4 14 T able 7. Site Con figurable Jumper Optio ns. a Pilot V alve /First S tage Oil V alve (V alve/S tart) T erminal 21. b A 30 second MFEP can be accomplished by addi ng a jumper wire between T erminals 19 and 5. SERVICE NOTE :Clipping and removing a site-configurable jumper enh ...

  • Honeywell RM7800E - page 15

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MODULES 15 66-1085—04 T able 8. Static Checkout. T est No. RM7800/ RM7840 Models Te s t Jumpers V oltmeter Normal Operatio n If Operation is Abnormal, Check the Item s Listed Below 1 All None 4-L2 Line voltage at T erminal 4. 1. Master Switch. 2. Power connected to the Master Switch. 3. Overload pr ...

  • Honeywell RM7800E - page 16

    RM7800E,G ,L,M; R M7840E,G ,L,M 7800 SERIES RELAY MODULES Automation and Co ntrol Solutions Honeywell Internationa l Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Toronto, Ontario M1V 4Z9 customer.honeywell.com ® U.S. Regi stered T rademark © 2010 Honeywell International Inc. 66-1085? ...

メーカー Honeywell カテゴリー Burner

Honeywell RM7800Eのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RM7800Eの取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell RM7800Eの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell RM7800Eの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell RM7800Eの取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell RM7800Eのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell RM7800Eの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell RM7800Eデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell RM7800Eを使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell RM7800Eユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell RM7800Eの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell RM7800Eの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell RM7800Eに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell RM7800Eデバイスの基本機能を使うにあたってのヒント。 Honeywell RM7800Eのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell RM7800Eに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell RM7800Eのメーカー/サービスへの連絡先に関する情報。

Honeywell RM7800Eについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell RM7800Eの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell RM7800Eで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)