Ariens 920022の取扱説明書

25ページ 2.79 mb
ダウンロード

ページに移動 of 25

Summary
  • Ariens 920022 - page 1

    Quick St art Guide Compact 24 LET (9 20022 s/n 000101 & up) • Step 1: Assembl e Handlebar • Step 2: Install T rigger Cable Assembly • Step 3: Install Discharge Chute • Step 4: Install Discharge Chute Crank • Step 5: Install Remote Deflec tor Cable • Step 6: Check Functi on of Dual Handle Interloc k • Step 7: Check T rack T ension ...

  • Ariens 920022 - page 2

    Step On e: Assemble Handlebar 1. Remov e the lower and loosen the upper hardw are on the handlebar assembly . 2. Loosen the hardware on the shift rod. 3. Put the speed selector lev er in the sixth forward position. 4. Rotate the handlebar into operating posit ion. NOTE: Be careful not to damage c able spring hooks when rotatin g handlebar upw ard. ...

  • Ariens 920022 - page 3

    Step T wo: Ins t all T rigger Cable Assembly NOTICE: T rigger cable assembly comes attached to the Sno -Thro unit. 1. Attach remote trigger cable assembly to upper handlebar assembly using one ¼” x 1- ½” ov al head machine screw and one ¼” locking w asher . ...

  • Ariens 920022 - page 4

    Step Thr ee : Ins t all Dischar ge Chut e 1. Grease underside of discharge chute ring (if not already greased). 2. Remov e mounting hardw are from auger housing 3. Install discharge chute ov er opening in the auger housing. Finger tighten the mounting hardw are remov ed abov e. NOTE: Leav e discharge chute pedestal loos e to help install the chute ...

  • Ariens 920022 - page 5

    Step F our: Ins t all Discharg e Chut e Cr ank 1. Remov e gear cover from top of chute pedestal. 2. Slide Chute Crank through the ny lon bushing in the support bracket under control panel. NOTE: Be careful not to damage nylon bushing when attaching crank to the control panel. 3. Connect the c hute crank to the pinion gear on discharge chute with sp ...

  • Ariens 920022 - page 6

    Step Fiv e: In s t all R emote Deflect or Cable 1. Pull rubber seal cap away from snap fitting. 2. Install snap fitting int o cable bracket’ s mounting hole located under the dash. 3. Position rubber seal cap ov er the top of snap fitting. 4. Move deflector control lev er to rear most position. 5. Attach cable ey e to pin on bottom of deflector c ...

  • Ariens 920022 - page 7

    6. Secure cable eye to control lever with sleev e bushing and hairpin. 7. Using the w ire hook attached to the deflector cable, hook cable to discharge chut e crank. 8. Install cable into clip on top of discharge chut e pedestal. 9. Make sure deflector cable loops abov e gear cover between cable clip and cable s upport bracket. 10. T est controls t ...

  • Ariens 920022 - page 8

    St ep Six: Check Function of Dual Handle Int erlock Without the engine running , press dow n (engage ) both clutch levers. Relea se attachment clutch lever . Attachment clutch shoul d remain engage d until traction clu tch lever is released , then both clutches must disenga ge. If they do not, contact your dealer for repairs. ...

  • Ariens 920022 - page 9

    St ep Sev en: Check T r ack T ension Check tracking of unit and tension the tracks as required (see T raction T ension Adju stment in Ow ners Manual). ...

  • Ariens 920022 - page 10

    St ep Eigh t: Adjus t Skid Shoes IMPORT A NT : Skid shoes should be adjusted as conditions require. All ow 1/8 in. (3mm) between scraper blade and hard smooth s urfaces. Allow 7/8 in (22 mm) between scraper blade and unev en or gravel surfaces . (See Skid Shoes in Owners Manual). ...

  • Ariens 920022 - page 11

    Check oil le vel in auger gearcase (see Check Auger Gearcase in Ow ners Manual). St ep Nine: Check Aug er Gear case Oil ...

  • Ariens 920022 - page 12

    IMPORT A NT : The engin e is shipped with 5W-30 oil in crankcase. Refer to engine manual for detailed instructions. St ep T en: Check Engine Cr ank case Oil ...

  • Ariens 920022 - page 13

    Fill fuel tank. DO N OT OVERFILL! See FILLING FUEL T ANK in Ow ners Manual. St ep Elev en: Fill Engine Fuel T ank ...

  • Ariens 920022 - page 14

    St ep T w elv e: St arting the Engine ...

  • Ariens 920022 - page 15

    St arting Engine / Step A: Chok e T urn choke ON. ...

  • Ariens 920022 - page 16

    St arting Engine / Step B: R ock er S wit ch Push rocker switch to RUN position. ...

  • Ariens 920022 - page 17

    St arting Engine / Step C: Fuel Shut Off V alve T urn fuel petcock to ON position. ...

  • Ariens 920022 - page 18

    St arting Engine / Step D: K ey Install Safety K ey Switch. Insert ignition key into slot but DO NOT turn the key . B e sure ignit ion key snaps into place. ...

  • Ariens 920022 - page 19

    St arting Engine / Step E: Prime Prime sy stem: 3 primes maxi mum. DO NOT over prime system. Make sure to cover the v ent hole on primer bulb before the primer bulb is compressed. Hold the primer bulb in the compressed position for one full second each time you press it. Repeat for a tot al of 3 primes. ...

  • Ariens 920022 - page 20

    St arting Engine / Step F: (Manual St art) Grasp rope handle. Pull slowly until resistance is felt, then pull rope firmly and quickly to start engine and avoid kickback. ...

  • Ariens 920022 - page 21

    St arting Engine / Step F: (Electric St art) Use a 3-wire ex tension cord and plug cord into starter motor adaptor first. Then plug cord into wall receptacle. Use appropriately sized extension cord (10A WG or larger) to prevent damage to electric starter . ...

  • Ariens 920022 - page 22

    St arting Engine / Step G: (Electric St art) Press and hold starter button. Note : Do not hol d the electric starter button down for more than 5 seconds. W ait at least 1 minute before additional starting attempts. ...

  • Ariens 920022 - page 23

    St arting Engine / Step H: W arm up Allow the engine to warm up for 1- 2 minutes, move the choke control to the CHOKE OFF position. ...

  • Ariens 920022 - page 24

    St ep Thirt een: Stopp ing the Engine Under normal condition s: 1. Push rocker sw itch to STOP position. 2. Pull safety key OUT . T o stop engine in an emergency , fli p the Rocker Sw itch to the ST OP position, OR Pull Safety Key from Engine. ...

  • Ariens 920022 - page 25

    Additional R esour ces • R e f er t o O wner s Manual and Engine Manual • Con t act Ariens Compan y www .ariens.com Phone: 920- 756 - 4688 E-mail: inf o@ari ens.com 2013 The Ariens Com pan y . All rights r eserved. ...

メーカー Ariens カテゴリー Snow Blower

Ariens 920022のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 920022の取扱説明書
- Ariensの製品カード
- パンフレット
- またはAriens 920022の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ariens 920022の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ariens 920022の取り付け説明書、サービスマニュアル、簡易説明書、またはAriens 920022のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ariens 920022の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ariens 920022デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAriens 920022を使用するのを助ける技術的文書のことです。説明書は通常、全てのAriens 920022ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ariensの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ariens 920022の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAriens 920022の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ariens 920022に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ariens 920022デバイスの基本機能を使うにあたってのヒント。 Ariens 920022のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ariens 920022に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAriens 920022のメーカー/サービスへの連絡先に関する情報。

Ariens 920022についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAriens 920022の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAriens 920022で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)