Jonsered 2125の取扱説明書

32ページ 1.45 mb
ダウンロード

ページに移動 of 32

Summary
  • Jonsered 2125 - page 1

    GT 2125 GC 2125 Operator’ s manual (EP A) Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine. ...

  • Jonsered 2125 - page 2

    2 – English KEY T O SYMBOLS Symbols W ARNING! Clear ing saws , brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • A protect ...

  • Jonsered 2125 - page 3

    English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Jonsered has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment. So alwa ys use approved hearing protection. ...

  • Jonsered 2125 - page 4

    4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es should be wor n when necessar y , e.g., when fi tting cutting attachments. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection. If you use a visor then you m ust also wear approv ...

  • Jonsered 2125 - page 5

    English – 5 SAFETY INSTR UCTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to reduce vibration and mak e operation easier . Use of incorrectly wound cord or an incorrect cutting attachment increases the le vel of vibr ation. The machine ′ s vibration damping system reduces the transf er ...

  • Jonsered 2125 - page 6

    6 – English SAFETY INSTR UCTIONS Chec king, maintaining and servicing the machine ′′ ′ ′ s safety equipment Throttle loc k • Make sure the throttle control is loc ked at the idle setting when the throttle lock is released. • Press the throttle lock and mak e sure it retur ns to its original position when you release it. • Check that ...

  • Jonsered 2125 - page 7

    English – 7 SAFETY INSTR UCTIONS • Regularly check that the muf fl er is securely attached to the machine. • If the muf fl er on y our machine is fi tted with a spark arrestor mesh then it should be cleaned regularly . A bloc ked mesh causes the engine to ov erheat, which can lead to serious damage. Nev er use a muf fl er with a def ectiv ...

  • Jonsered 2125 - page 8

    8 – English SAFETY INSTR UCTIONS Cutting equipment Sharpening grass cutters and grass blades • See the cutting attachment packaging f or correct shar pening instructions. • Shar pen blades and cutters using a single-cut fl at fi le . • Shar pen all edges equally to maintain the balance of the blade . T rimmer head • Only use the recomme ...

  • Jonsered 2125 - page 9

    English – 9 SAFETY INSTR UCTIONS General safety precautions Starting • The complete clutch cov er and shaft must be fi tted before the machine is star ted, otherwise the clutch can come loose and cause personal injur y . • Ne ver start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Obser ve y our surroundings and make su ...

  • Jonsered 2125 - page 10

    10 – English SAFETY INSTR UCTIONS • The transpor t guard must alwa ys be fi tted to the cutting attachment when the machine is being transpor ted or in storage. General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine . • T o ensure that ...

  • Jonsered 2125 - page 11

    English – 11 SAFETY INSTR UCTIONS Grass trimming using a trimmer head and plastic blades T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Nev er press the cord into the area to be cut. • The cord can easily remov e grass and weeds up against ...

  • Jonsered 2125 - page 12

    12 – English WHA T IS WHA T? What is what on the trimmer? 30 1 T r immer head 2 Grease fi ller cap , be vel gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop s witch 9 Throttle lock 10 Cylinder cov er 11 Star ter handle 12 Fuel tank 13 Choke control 14 Air purge 15 Air fi lter cov er 16 Handle adjustm ...

  • Jonsered 2125 - page 13

    English – 13 ASSEMBL Y Fitting the loop handle (GT 2125) • P osition the handle on the shaft. Note that the handle must be mounted below the arro w on the shaft. • Fit the screw , secur ing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (GC 2125) • Clip the loop handle onto the shaft. Note that ...

  • Jonsered 2125 - page 14

    14 – English ASSEMBL Y Fitting the trimmer guar d and A uto 32 trimmer head (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fi tting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft. • T ur n the blade shaft until one of the holes in the drive di ...

  • Jonsered 2125 - page 15

    English – 15 ASSEMBL Y Fitting other guar ds and cutting attachments (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fi tting on the shaft and secure with the bolt (L). • Fit the drive disc (B) on the output shaft. • T ur n the blade shaft until one of the holes ...

  • Jonsered 2125 - page 16

    16 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-strok e engine and must alwa ys been run using a mixture of gasoline and two-strok e engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, e ven small inaccurac ...

  • Jonsered 2125 - page 17

    English – 17 FUEL HANDLING Fueling • Clean the area around the fuel cap . Contamination in the tank can cause operating prob lems. • Ensure that the fuel is well mix ed by shaking the container bef ore fi lling the tank. ! W ARNING! T aking the following precautions, will lessen the risk of fi re: Do not smoke or place hot objects near fuel ...

  • Jonsered 2125 - page 18

    18 – English ST AR TING AND ST OPPING Chec k before starting • Check that the support fl ange is not crack ed due to fatigue or due to being tightened too much. Discard the suppor t fl ange if it is crac ked. • Ensure the locking n ut has not lost its captive f orce. The nut loc k should hav e a locking force of at least 1.5 Nm. The tighten ...

  • Jonsered 2125 - page 19

    English – 19 ST AR TING AND ST OPPING some resistance (the star ter pawls grip), now quic kly and powerfully pull the cord. Never wrap the starter cord ar ound your hand Repeat pulling the cord until the engine star ts. When the engine star ts. return choke control to run position and apply full throttle; the throttle will automatically disengage ...

  • Jonsered 2125 - page 20

    20 – English MAINTENANCE Carb uretor Y our Jonsered product has been designed and manuf actured to speci fi cations that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. T o ensure that the engine runs at peak performance and produces as little harmful exhaust fumes as possible after the running-in pe ...

  • Jonsered 2125 - page 21

    English – 21 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T , if it is necessar y to readjust. First tur n the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly a ...

  • Jonsered 2125 - page 22

    22 – English MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder . 4 Cylinder cov er (directs cold air over the cylinder). Clean the cooling system with ...

  • Jonsered 2125 - page 23

    English – 23 MAINTENANCE Spark plug The spark plug condition is in fl uenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air fi lter . These f actors cause deposits on the spark plug electrodes, which ma y result in operating problems and starting dif fi culties. If t ...

  • Jonsered 2125 - page 24

    24 – English TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le v el is calculated as the time-weighted energy total f or noise pressure le vels under v ar ious working conditions with the follo wing time distr ibution: 1/2 idle and 1/2 max. speed. NO TE! Noise pressure at the user’s ear and vibr ation on the handles are mea ...

  • Jonsered 2125 - page 25

    English – 25 TECHNICAL D A T A Appro ved accessories T ype Cutting attachment guar d, Art. no. GT 2125 Blade shaft thread 3/8 R T r immer head T ap-N-Go VII (R) 530 05 60-57 GC 2125 Arbor shaft thread M10 T r immer head T r immy H II 503 93 42-04 / 503 97 71-03 A uto32 503 93 42-04 / 503 97 71-03 S35 503 93 42-04 / 503 97 71-03 T ap n’Go 35 503 ...

  • Jonsered 2125 - page 26

    26 – English FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to e xplain the emissions control system warranty on y our 2001 and later small nonroad engine. In U.S . and Canada, new small nonroad engines must be d ...

  • Jonsered 2125 - page 27

    1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6" ...

  • Jonsered 2125 - page 28

    "Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35 ...

  • Jonsered 2125 - page 29

    1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5 ...

  • Jonsered 2125 - page 30

    ´®z*x}3¶5U¨ ´®z*x}3¶5U¨ T ap-N-Go 35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm ...

  • Jonsered 2125 - page 31

    1 Auto 32 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " 15 cm 15 cm ...

  • Jonsered 2125 - page 32

    ´®z*x}3¶5U¨ 2004-06-14 ´®z*x}3¶5U¨ 1088931-95 ...

メーカー Jonsered カテゴリー Trimmer

Jonsered 2125のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2125の取扱説明書
- Jonseredの製品カード
- パンフレット
- またはJonsered 2125の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Jonsered 2125の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Jonsered 2125の取り付け説明書、サービスマニュアル、簡易説明書、またはJonsered 2125のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Jonsered 2125の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Jonsered 2125デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJonsered 2125を使用するのを助ける技術的文書のことです。説明書は通常、全てのJonsered 2125ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Jonseredの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Jonsered 2125の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJonsered 2125の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Jonsered 2125に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Jonsered 2125デバイスの基本機能を使うにあたってのヒント。 Jonsered 2125のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Jonsered 2125に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJonsered 2125のメーカー/サービスへの連絡先に関する情報。

Jonsered 2125についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJonsered 2125の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJonsered 2125で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)