Weed Eater TILLER WET6500Aの取扱説明書

28ページ 1.05 mb
ダウンロード

ページに移動 of 28

Summary
  • Weed Eater TILLER WET6500A - page 1

    OWNER'S MANUAL MODEL NO.WET6500A 6.5 HP 17 Inch Tiller Assembly • Operation Maintenance • Service and Adjustments • Storage • Troubleshooting • Repair Parts For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886 WEED EATER 186100 Rev. 1 02.21.03 TR PRINTED IN U.S.A ...

  • Weed Eater TILLER WET6500A - page 2

    SAFETY RULES SAFE OPERATION PRACTICES FOR WALK-BEHIND POWERED ROTARYTILLERS TRAINING Read the Owner's Manual carefully, Be thoroughly familiar with the controls and the proper use of the equipment, Know how to stop the unit and disengage the controls quickly. • Never allow children to operate the equipment. Never allow adults to operate the ...

  • Weed Eater TILLER WET6500A - page 3

    PRODUCT SPECIFICATIONS GASOLINE CAPACITY: 3 Quarts (2.8L) Unleaded Regular OIL (API-SF-SJ): SAE 30 (Above 32°F/0°C) (Capacity: 20 ozJ0.6L) SAE 5w-30 (Below 32°F/0°C) SPARK PLUG : - Champion GAP: .030"/0,76mm) RJ19LM CONGRATULATIONS on your purchase of a new tiller. It has been designed, engineered and manufactured to give you the best poss ...

  • Weed Eater TILLER WET6500A - page 4

    ...

  • Weed Eater TILLER WET6500A - page 5

    ...

  • Weed Eater TILLER WET6500A - page 6

    ASSEMBLY CONNECT SHIFT ROD (See Fig. 7) ATTACH CLUTCH CABLE (See Fig. 6) • Hook end of clutch cable through hole in control bar bracket if necessary. END OF CONTROL BAR CLUTCH CABLE BRACKET CONTROLBAR BRACKET BAR CLUTCH CABLE FIG. 6 • Insert end of shift rod into hole of shift lever indicator. Insert hairpin clip through hole of shift rod to se ...

  • Weed Eater TILLER WET6500A - page 7

    KNOWYOUR TILLER OPERATION L READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrationswith your tiller to familiarize yourself with the location of various controls and adjustments, Save this manual for" futui'e reference. These symbols may appear on your Tiller or in literature supplied with th ...

  • Weed Eater TILLER WET6500A - page 8

    OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO USE YOUR TILLER Know how to operate all co ...

  • Weed Eater TILLER WET6500A - page 9

    OPERATION TURNING • • Release the drive control bar. • Move throttle control to "SLOW" position. Place shift leverindicatorin"F' (forward) position. Tines will not turn. • Lift handle to raise tines out of ground. • Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away fr ...

  • Weed Eater TILLER WET6500A - page 10

    ..... OPERATION TO START ENGINE (See Fig. 13) TILLING HINTS I _[]L CAUTION: Keep drive control bar in "DISENGAGED" position when start- ing engine. When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine• • Make sure spark plug wi ...

  • Weed Eater TILLER WET6500A - page 11

    OPERATION TINE SHEAR PINS The tine assemblies on your tiller are secured to the tine shaft with shear pins (See 'q-INE REPLACEMEN'I "_ in the Service and Adjustments section of this manual). If the tiller is unusually overloaded or jammed, the shear pins are designed to break before internal damage occurs to the transmission. • If ...

  • Weed Eater TILLER WET6500A - page 12

    MAINTENANCE I MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Y SERVICE DATES Check Engine Oil Level li/' !_ Change Engine Oil 1_1,2 Oil Pivot Points If Inspect Spark Arrester/Muffler V' Inspect Air Screen I_ Clean or Replace Air Cleaner Cartridge I/2 Clean Engine Cylinder Fins Ii/ Replace Spark Plug RH Gear Case Grease ...

  • Weed Eater TILLER WET6500A - page 13

    MAINTENANCE Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot m ...

  • Weed Eater TILLER WET6500A - page 14

    r i MAINTENANCE .... MUFFLER COOLING SYSTEM (See Fig. 21) Your engine is air cooled. For proper engine performance and long life keep your engine clean. • Clean air screen frequently using a stiff-bristled brush. • Remove blower housing and clean as necessary. • Keep cylinder fins free of dirt and chaff. CYLINDER FINS MUFFLER HOUSING SCREEN F ...

  • Weed Eater TILLER WET6500A - page 15

    SERVICE AND ADJUSTMENTS IA TILLER CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into ' I contact with plug. I TO ADJUST HANDLE HEIGHT (See Fig. 22) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • First loosen handle lock leve ...

  • Weed Eater TILLER WET6500A - page 16

    SERVICE AND ADJUSTMENTS TINE REPLACEMENT (See Figs. 24, 25 and 26) I_1) CAUTION: Tines are sharp. Wear gloves or other protection when han- dling tines, A badly worn tine causes your tiller to work harder and dig more shallow. Most important, worn tines cannot chop and To maintain the superb tilling performance of this machine the tines should be c ...

  • Weed Eater TILLER WET6500A - page 17

    SERVICE AND ADJUSTMENTS TO REMOVE BELT GUARD (See Fig. 27) NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch (2.5 cm). • Remove two (2) screws from side of belt guard. • Remove hex nut and washer from bottom of belt guard (located behind wheel). • Pull belt guard out and awa ...

  • Weed Eater TILLER WET6500A - page 18

    SERVICE AND ADJUSTMENTS ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29) The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, proceed as follows: • With engine not running, move remote throttle control lever to "FAST" position. • If throttle lever on engine touche ...

  • Weed Eater TILLER WET6500A - page 19

    STORAGE Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more. TILLER Clean entire tiller (See "CLEANING" inthe Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of t ...

  • Weed Eater TILLER WET6500A - page 20

    TROUBLESHOOTING POINTS . CAUSE CORRECTION PROBLEM Will not start Hard to start Loss of power Engine overheats Excessive bounce/ difficult handling Soil balls up or clumps Engine runs but tiller won't move Engine runs but labors when tilling Tines will not rotate Hard to shift into gear Tiller shuts off when drive control bar engaged 1. Out of ...

  • Weed Eater TILLER WET6500A - page 21

    REPAIR PARTS TILLER -- MODEL NUMBER WET6500A HANDLE ASSEMBLY 42 41 1 29 35 2 35 15 2 37 26 21 / KEY NO. 1 2 4 8 10 11 15 16 17 18 19 20 21 PART NO. 175769 150744 159227 71191008 8389J 4497H 108281X 72110608 109229X 73680600 19131611 109228X 150217 DESCRIPTION Control, Throttle Grip, Handle Bar, Control Screw, Pan Hd. #10-24 Grip, Handle Clip, Hai ...

  • Weed Eater TILLER WET6500A - page 22

    REPAIR PARTS TILLER - - MODEL NUMBER WET6500A MAINFRAME, LEFT SIDE 3 65 37 36 35 I / 34 31 3O 2 16 19 28 3 4O 4O - 23 15 24 KEY PART NO. NO. 1 73510500 2 10040600 3 73220600 4 170127 5 164329 6 110111X 7 72110404 8 8700J 9 86777 10 9484R 11 10040400 12 73220400 13 23230506 14 156117 15 19111116 16 145102 19 12000028 21 110652X 22 74770508 23 ...

  • Weed Eater TILLER WET6500A - page 23

    REPAIR PARTS TILLER - - MODEL NUMBER WET6500A MAINFRAME, RIGHT SIDE 11 5 I k lO KEY NO. 5 7 8 9 10 11 12 PART NO. 102332X 102173X 10040600 73220600 74760524 4497H 126875X DESCRIPTION Bracket, Reinforcement CounterWeight, R.H. Washer, Lock 3/8 Nut, Hex 3/8-16 Bolt, Hex 5/16-18 x 1-1/2 Clip, Hairpin Rivet, Drilled KEY PART NO. NO. DESCRIPTION 13 1021 ...

  • Weed Eater TILLER WET6500A - page 24

    ...

  • Weed Eater TILLER WET6500A - page 25

    ...

  • Weed Eater TILLER WET6500A - page 26

    REPAIR PARTS TILLER - - MODEL NUMBER WET6500A TINE ASSEMBLY 2 I 1 1 11 2 8 9 9 4 9 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 4459J Tine, Outer, L.H. 8 74610616 Bolt, Hex 3/8-24 x 1 2 132673 Clevis Pin 9 4460J Tine, Outer, R.H. 3 6554J Tine, Inner, LH. 10 132728 Assembly, Hub and Plate, R.H. 4 3146R Clip, Hairpin 11 6555J Tine, I ...

  • Weed Eater TILLER WET6500A - page 27

    REPAIR PARTS TILLER -- MODEL NUMBER WET6500A DECALS 4 10 12 9 KEY PART NO. NO. 1 162846 3 186761 4 143678 5 141907 6 102180× 9 141906 10 156199 12 162215 - - 186100 - - 186101 DESCRIPTION Decal, Logo Decal, Logo Decal, Instruction, Tilling Decal, Hand Placement Decal, Shift Indicator Decal, Warning, Rotating Tines Deal, Reverse Decal, Tine Shield ...

  • Weed Eater TILLER WET6500A - page 28

    LIMITED WARRANTY "[he Manufacturer warrar;ts to the (_riginal consumer purchaser thatthis product as rnanufa(_ture_is free from de- fects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in r ...

メーカー Weed Eater カテゴリー Tiller

Weed Eater TILLER WET6500Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TILLER WET6500Aの取扱説明書
- Weed Eaterの製品カード
- パンフレット
- またはWeed Eater TILLER WET6500Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Weed Eater TILLER WET6500Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Weed Eater TILLER WET6500Aの取り付け説明書、サービスマニュアル、簡易説明書、またはWeed Eater TILLER WET6500Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Weed Eater TILLER WET6500Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Weed Eater TILLER WET6500Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWeed Eater TILLER WET6500Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのWeed Eater TILLER WET6500Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Weed Eaterの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Weed Eater TILLER WET6500Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWeed Eater TILLER WET6500Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Weed Eater TILLER WET6500Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Weed Eater TILLER WET6500Aデバイスの基本機能を使うにあたってのヒント。 Weed Eater TILLER WET6500Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Weed Eater TILLER WET6500Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWeed Eater TILLER WET6500Aのメーカー/サービスへの連絡先に関する情報。

Weed Eater TILLER WET6500Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWeed Eater TILLER WET6500Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWeed Eater TILLER WET6500Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)