Cisco Systems N55M4Qの取扱説明書

36ページ 3.67 mb
ダウンロード

ページに移動 of 36

Summary
  • Cisco Systems N55M4Q - page 1

    CH A P T E R 2-1 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 2 Switch Installation This chapter describes ho w to start your switch and ho w to interpret the po wer-on self-test (POST) that ensures proper operation. I t also describes ho w to install the switch. Read the topics and perform th e procedures in this orde ...

  • Cisco Systems N55M4Q - page 2

    2-2 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Preparing for Installation War ni ng Read the wall-mounting in structions carefully before beginnin g installation. Failure to use the correct hardware or to follow the corre ct procedures could result i n a hazardous situa tion to people a ...

  • Cisco Systems N55M4Q - page 3

    2-3 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Preparing for Installation War ni n g For connections outside the build ing where the equipment is installed, the follo wing ports must be connected through an approved network termina tion unit with integral circuit protection: 10/100/1000 ...

  • Cisco Systems N55M4Q - page 4

    2-4 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Powering the Switch • T emperature arou nd the unit does not e xceed 113°F (45°C). If the switch is installed in a closed en vironment or in a multirack assembly , the temperature aroun d it might be greater than nor mal room temperatur ...

  • Cisco Systems N55M4Q - page 5

    2-5 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Verifying Switch Operation Note Y ou can use both the u plink port an d the auxiliar y po wer adapter . Howev er, the auxiliary po wer input takes preced ence. Catalyst 35 60CPD-8PT -S • Connect a 10/100/10 00 uplink port to a PoE+ switch, ...

  • Cisco Systems N55M4Q - page 6

    2-6 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch On a Desk or Shelf (without Mounting Screws) Step 1 Locate the adhesiv e strip with the ru bber feet in the accessory kit. Step 2 Remov e the four rubber feet from the adhesi ve strip, and attach th em to the recessed ar ...

  • Cisco Systems N55M4Q - page 7

    2-7 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-1 Installing the Mo unting Screws on T op of a Desk or a Shelf Step 3 Peel the adhesi ve strip of f the bottom of the scre w template, and attach it to the top of the desk or shelf. Step 4 Use a 0.144-inch (3.7 m ...

  • Cisco Systems N55M4Q - page 8

    2-8 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch Figur e 2-2 Mounting the Switc h on T op of a Desk or Shelf After you mount the switch, see the “ After Installing the Switch” section on page 2-31 for info rmation about conf iguring the switch. Under the Desk- or S ...

  • Cisco Systems N55M4Q - page 9

    2-9 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-3 Installin g the Moun ting Screws Un der a Desk or Shelf Step 4 Use a 0.144-inch (3.7 mm) or a #27 d rill bit to drill a 1/2-inch (12.7 mm) ho le in the three scre w template slots. Step 5 Insert three scre ws i ...

  • Cisco Systems N55M4Q - page 10

    2-10 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch Figur e 2-4 Mounting the S witch Under a Desk or Shelf After you mount the switch, see the “ After Installing the Switch” section on page 2-31 for info rmation about conf iguring the switch. Wall-Mounting War ni ng ...

  • Cisco Systems N55M4Q - page 11

    2-11 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 1 Locate the scre w template. The template is used t o align the mounting scre w holes. Note Figure 2-5 sho ws the measurements for the lo ca tion of the sc rews on the switch. Step 2 Position the scre w template so ...

  • Cisco Systems N55M4Q - page 12

    2-12 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch Figure 2-6 Installing th e Mounting Screws on the W all Figure 2-7 Installing th e Switc h on a W all Step 8 Place the switch onto the mo unting scre ws, and slide it down unt il it locks in place. See Figure 2- 7 . CAB ...

  • Cisco Systems N55M4Q - page 13

    2-13 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch With a Mounting Tray The mounting kit (part number CMP-MGNT -TRA Y=) is optional. Y ou can order it when you or der your switch, or you can order it l ater from your Cisco representati ve. The mounting kit shi ps content ...

  • Cisco Systems N55M4Q - page 14

    2-14 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch Step 4 Place the switch onto th e mounting scre ws, and slide the switch until it locks into place. See Figure 2-9 . Figure 2-9 Installing th e Switc h on the Mounting T ra y 1 Number-8 Phillips pan-head scre ws 3 Desk ...

  • Cisco Systems N55M4Q - page 15

    2-15 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 5 Use the two number -10 Phillips pan-head scre ws to secure the mounting tr ay to the switch. See Figure 2-10 . Figur e 2-1 0 Secur ing the Moun ting T r ay to the S witch War ni n g T o prevent airflo w restrictio ...

  • Cisco Systems N55M4Q - page 16

    2-16 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch Step 1 Place the switch on the mounting tray . See Figure 2-11 . Figur e 2-1 1 Placing the Swit ch on the Mounting T ra y Step 2 Use the two number -10 Phillips pan-head scre ws to secure the mounting tr ay to the switc ...

  • Cisco Systems N55M4Q - page 17

    2-17 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch War ni n g Read the wall-mounting in structions carefully before beginnin g installation. Failure to u se the correct hardware or to follow the corre ct procedures could result in a hazardous situation to people and dama ...

  • Cisco Systems N55M4Q - page 18

    2-18 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch In a Rack Installing the switch in a rack r equires an optional bracket k it that is not incl uded with the swi tch. Y ou can order these kits from your Cisco representat i ve: • 19-inch rack-mounting brackets (RCKMNT ...

  • Cisco Systems N55M4Q - page 19

    2-19 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-15 sh ow s ho w to attach a 23-inch bracket to one side o f the switch. Fol lo w the same steps to attach the second bracket to the opposite side. Figure 2-15 Attac hing the 23-inch Br ack ets for Rac k-Mounting ...

  • Cisco Systems N55M4Q - page 20

    2-20 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch On a DIN Rail The DIN-mount kit (part number CMP-DIN- MNT=) is optional. Y ou can order it when you order your switch, or you can order it l ater from your Cisco representati ve. The DIN-mount kit contains: • T w o nu ...

  • Cisco Systems N55M4Q - page 21

    2-21 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 2 Use the two number -10 Phillips pan-head scre ws to secure the DIN rail mount to the switch. See Figure 2-18 . Figur e 2-18 Secur ing the DIN- Mount T ra y to the Switc h Mounting the Switch on a DIN Rail Caution ...

  • Cisco Systems N55M4Q - page 22

    2-22 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Mounting the Switch Figure 2-19 Mounting the Switch on a DIN Rail Step 2 Rotate the switch do wn towa rd the DIN rail until the release tabs on the DIN rail mount clicks. Step 3 Lift lightly on t he bottom of the switch to en sure that it ...

  • Cisco Systems N55M4Q - page 23

    2-23 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Removing the Switch from a DIN Rail Step 1 Ensure that power i s remov ed from the switch, and disconnect all cables and connectors fr om the front panel of th e switch. Step 2 Pull do wn on the DIN rail mount release ta ...

  • Cisco Systems N55M4Q - page 24

    2-24 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Installing a Cover for t he Reset Button (Optional) Installing a Cover for the Reset Button (Optional) Y ou can cov er the reset button to pre vent accidental or unauth orized reset of your switch. T o in stall a cov er on the reset button ...

  • Cisco Systems N55M4Q - page 25

    2-25 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Installing the Power Cord Retainer (Optional) Installing the Power Cord Retainer (Optional) Note This section applies to sw itches with an A C po wer connector . The power cor d retainer part number (PWR-CLP=) is optiona l. Y ou can order i ...

  • Cisco Systems N55M4Q - page 26

    2-26 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Installing the Po wer Cord Retain er (Optional) Step 3 Slide the retainer throu gh the f irst latch. See Figu re 2-24 . Figure 2-24 Sliding the Re tainer Through the Latc h Step 4 Slide the retainer throu gh the other latches to lock it. S ...

  • Cisco Systems N55M4Q - page 27

    2-27 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Installing the Power Cord Retainer (Optional) Figure 2-26 Sleev e Around the P ower Cord Step 6 Secure the A C po w er cord by pressing on the retainer . See Figure 2-27 . Figur e 2-27 Secur ing the Po wer Cord in the Retainer 1 Slee ve for ...

  • Cisco Systems N55M4Q - page 28

    2-28 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Installing the Cabl e Guard (Optional) Installing the Cable Guard (Optional) The cable guard pre vents tampering with the cables after the cables are installed. The cable guard (CMP-CBLE-GRD=) is not included with the swi tch, but you can ...

  • Cisco Systems N55M4Q - page 29

    2-29 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Installing the Cable Guard (Optional) Step 2 Use the supplied number -10 pan-head scre ws to attach the cable gu ard to the switch. See Figure 2-29 . Figure 2-29 Attac hing the Ca ble Guard t o the Switc h Step 3 Loosen the number -10 Phill ...

  • Cisco Systems N55M4Q - page 30

    2-30 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Installing the Cabl e Guard (Optional) Figure 2-31 Attac hing the Cables to the S witch Step 4 Guide the connected cables through th e slots in the front of the cable guard. Slide the c able guide in as sho wn in Figure 2-33 . T ighten the ...

  • Cisco Systems N55M4Q - page 31

    2-31 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation After Installing the Switch Step 5 (Optional) T o attach the cable guard t o the desk or w all, use a 0.144-i nch (3.7 mm) or a #27 drill b it to drill 1/2-inch (1 2.7 mm) holes at each of the tw o mounting locations. Insert the suppl ied 0 ...

  • Cisco Systems N55M4Q - page 32

    2-32 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Removing SFP Modules War ni ng Class 1 laser product. Statement 1008 Step 1 Attach an ESD-pre v enti ve wri st strap to your wrist an d to a bare metal surface. Step 2 Find the send (TX) and recei ve (RX) markings on the module top. On som ...

  • Cisco Systems N55M4Q - page 33

    2-33 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Connecting De vices to the Ethernet Ports Figure 2-35 Removing a Bale -Clasp Latch SFP Module Connecting Devices to the Ethernet Ports • Connecting to the 10/10 0 and 10/100/1000 Ports, page 2-33 • Connecting to the PoE Ports, pag e 2-3 ...

  • Cisco Systems N55M4Q - page 34

    2-34 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Connecting Devices to the Eth ernet Ports Figur e 2-36 Connecting to an Ether net P ort Connecting to the PoE Ports The 10/100 PoE ports ha ve the same autoneg otiation settings and cabling requirements as those in t he “Connecting to th ...

  • Cisco Systems N55M4Q - page 35

    2-35 Catalyst 3560-C and 2960-C Switch Hardware Installati on Guide OL-23803-02 Chapter 2 Switch Installation Where to Go Next restricted access location and users and service peo ple who are authorized w ithin the restricted access location are made aware of the haza rd. A restricted access area can be accessed only through the use of a special to ...

  • Cisco Systems N55M4Q - page 36

    2-36 Catalyst 3560-C and 2960-C Switch Hardware Inst allation Guide OL-23803-02 Chapter 2 Switch Installatio n Where to Go Ne xt ...

メーカー Cisco Systems カテゴリー Switch

Cisco Systems N55M4Qのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- N55M4Qの取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems N55M4Qの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems N55M4Qの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems N55M4Qの取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems N55M4Qのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems N55M4Qの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems N55M4Qデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems N55M4Qを使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems N55M4Qユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems N55M4Qの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems N55M4Qの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems N55M4Qに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems N55M4Qデバイスの基本機能を使うにあたってのヒント。 Cisco Systems N55M4Qのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems N55M4Qに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems N55M4Qのメーカー/サービスへの連絡先に関する情報。

Cisco Systems N55M4Qについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems N55M4Qの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems N55M4Qで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)