Makita EW200TRの取扱説明書

20ページ 0.89 mb
ダウンロード

ページに移動 of 20

Summary
  • Makita EW200TR - page 1

    PUMP EW2OOTR MODEL EW3OOTR EW400TR INSTRUCTION MANUAL I ISSUEEMD-PU0835 I piEGKq ...

  • Makita EW200TR - page 2

    ...

  • Makita EW200TR - page 3

    FOREWORD Thank you for purchasing a Makita trash pump. This manual covers operation and maintenance of trash pumps. All information in this publication is based on the latest product infor- mation available at the time of approval for printing. Please read this manual carefully before operating. CONTENTS Page 1. PUMP SAFETY 1 2. COMPONENTS 2 3. PRE ...

  • Makita EW200TR - page 4

    ID PUMP SAFETY Please make sure you review each precaution carefully. SURROUNDINGS H Operate the pump on a stable, level surface free of small rocks, loose gravel, etc. H Keep pump at least 3 feet (1 meter) away from buildings. H Keep pump away from flammables and other hazardous materials (trash, rags, lubricants, explosives). FIRE PREVENTION m Be ...

  • Makita EW200TR - page 5

    Spark plug Fuel cock Speed control lever Fuel tank Plug(priming) Pump strainer Drain plug (at two places) -2- ...

  • Makita EW200TR - page 6

    3. PREPARATIONS FOR STARTING 1. Connect the suction hose. Use a reinforced-wall or wire braided hose to prevent suction collapse. Since the pump’s self-priming time is directly proportional to hose length, a short hose is recommended. tion hose. Gravel or debris sucked into the pump will cause serious 2. Connect the discharge hose. When using a f ...

  • Makita EW200TR - page 7

    4. Check the fuel level. If level is low, fill to the shoulder of the fuel filter. Use fresh, clean automotive gasoline. 5. Check the priming water. It is recommended that the water chamber of pump casing should be primed with full of water before operating. ICAUTION], . Never attempt to operate the pump without priming water or the pump will overh ...

  • Makita EW200TR - page 8

    4. STARTING THE ENGINE 1. Open the fuel cock. 2. Set the speed control lever to “START.” -. .. . . . EW400TR 3. Close the choke. m If the engine is warm or the ambient temperature is high, close the choke half-way, or keep it open fully. If the engine is cold, or the ambient temperature is low, close the choke. . -5- Choke knob -I EW400TR I ...

  • Makita EW200TR - page 9

    4. Pull the starter handle slowly until re- sistance is felt. This is the "compression" point. Return the handle to its original position and pull swiftly. Do not pull out the rope all the way. I After starting the engine, allow the starter handle return to its original position while still holding the handle. -6- ...

  • Makita EW200TR - page 10

    5. OPERATION 1. After starting the engine, gradually open choke by turning the choke lever and finally keep it open fully. H Do not fully open the choke immediately when the engine is cold or the ambient temperature is low, because the engine may stop. 2. After the engine starts, set the speed control lever at the low speed position (L) and warm it ...

  • Makita EW200TR - page 11

    6. STOPPING THE ENGINE 1. Set the speed control lever to the low speed position and allow the engine to run at low speed for 2 or 3 minutes before stopping. 2. Keep depressing the STOP BUTON until the engine stops. Do not stop the engine suddenly when it is running at high speed. 3. Close the fuel cock. 4. Pull the starter handle slowly and return ...

  • Makita EW200TR - page 12

    DAILY INSPECTION Before running the pump, check the following service items: Enough fuel. m Excessive vibration, noise. Clean air cleaner element. Safe surroundings. Enough clean engine oil. D Leakage of gasoline and engine oil. Loose or broken bolts and nuts. Check the priming water. 8 hours (daily) PERIODIC INSPECTION Periodic maintenance is vita ...

  • Makita EW200TR - page 13

    a. "HOW TOWAINTENANCE INSPECTING THE SPARK PLUG w Clean off carbon deposits on the plug electrode using a plug cleaner or wire brush. Check electrode gap. Adjust it to between 0.02 and 0.03 inches. (0.6 and 0.7") ENGINE OIL CHANGE Initial oil change ...... 20 hours of operation Thereafter.. .Every 50 hours of operation :CAUTION]- Make sur ...

  • Makita EW200TR - page 14

    SERVICING THE AIR CLEANER Maintaining an air cleaner in proper condition is very important. Dirt induced through im- properly installed, improperly serviced or in- adequate elements, wears out engines. Keep the element always clean. (a) Unlock the cover and remove the cleaner element. (b) Inner element:Wash the element with kerosene, then soak it i ...

  • Makita EW200TR - page 15

    Pump does not run. I Pumping volume is small. Pump does not self-prime. 7 c Engine does not start. (See page 13.) Sticking of impeller (Disassemble and clean.) Sucking air at suction side (Check piping at suction side.) Drop in engine output (Consult your nearest dealer.) Breakage of mechanical seal (Consult your nearest dealer.) High suction lift ...

  • Makita EW200TR - page 16

    fore you take the pump to your Makita dealer. If you still have trouble after com- pleting the checks, take the pump to your nearest Makita dealer. 1. Remove the plug and connect it to the plug cap. Pull the starter handle while putting the plug against the engine ground. 2. Try with a new plug if the spark is weak or no spark flies. 3. The ignitio ...

  • Makita EW200TR - page 17

    10. PREPARATIONS FOR STORAGE ~~~ ~ I Drain all water from the drain plug. , I When retightening drain plug, be sure to clean the drain plug and the thread of casincl. Otherwise, the [CAUTION 1u thread may be da6aged. II J 1 Remove the strainer cup, and open the strainer cock to discharge the fuel from the fuel tank. Remove the carburetor float cham ...

  • Makita EW200TR - page 18

    11 OIL SENSOR INSTRUCTIONS OIL SENSOR (OPTION) (a) The oil sensor detects the fall in oil level in the crankcase and automatically stops the engine when the oil level falls down below the predetermined level. (b) When engine has stopped automatically, check the oil level. Refill engine oil to the upper level and restart the engine. (c) If the engin ...

  • Makita EW200TR - page 19

    ...

  • Makita EW200TR - page 20

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period. retum the COMPLETE tool, freight ...

メーカー Makita カテゴリー Septic System

Makita EW200TRのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- EW200TRの取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita EW200TRの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita EW200TRの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita EW200TRの取り付け説明書、サービスマニュアル、簡易説明書、またはMakita EW200TRのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita EW200TRの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita EW200TRデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita EW200TRを使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita EW200TRユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita EW200TRの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita EW200TRの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita EW200TRに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita EW200TRデバイスの基本機能を使うにあたってのヒント。 Makita EW200TRのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita EW200TRに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita EW200TRのメーカー/サービスへの連絡先に関する情報。

Makita EW200TRについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita EW200TRの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita EW200TRで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)