日本語 dropdown-ico

Graco Inc. 232631の取扱説明書

26ページ 1.18 mb
ダウンロード

ページに移動 of 26

Summary
  • Graco Inc. 232631 - page 1

    308870 Rev . F First choice when quality counts. t Related Manuals Operation 308867 . . . . . . . . . . . . . . . . . . . . . . . . . . Displacement Pump 308798 . . . . . . . . . . . . . . . . . Spray Gun 309091 . . . . . . . . . . . . . . . . . . . . . . . . . Spray T ip 309055 . . . . . . . . . . . . . . . . . . . . . . . . . . . PC Board 308919 ...

  • Graco Inc. 232631 - page 2

    308870 2 W arnings and Cautions W arning Symbol W ARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. Fluid injection is a serious injury! If ...

  • Graco Inc. 232631 - page 3

    308870 3 Component Identification and Function Fig. 1 S U W T X V P A B C E F G H J K 202 Main hose 203 Whip end hose 204 Contractor gun with RAC 5 DripLess tip guard and 517 size SwitchTip 203 204 202 M N L Model 232631 R D 9034B A Pressure Control Switch ON/OFF , enables/disables clutch function and pressure control B Pressure Adjusting Knob Cont ...

  • Graco Inc. 232631 - page 4

    308870 4 Maintenance W ARNING INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally . Fluid under high pressure can be injected through the skin and cause serious injury . T o reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relie ...

  • Graco Inc. 232631 - page 5

    308870 5 T roubleshooting W ARNING INJECTION HAZARD T o reduce risk of serious injury , including fluid injection or splashing in eyes or on skin, or injury from moving parts, always follow Pressure Relief Procedure W arning , page 4, before checking, adjust- ing, cleaning or shutting down sprayer . PROBLEM CAUSE SOLUTION Engine won ’ t start Eng ...

  • Graco Inc. 232631 - page 6

    308870 6 PROBLEM CAUSE SOLUTION Pump output is low Strainer (31) is clogged Clean strainer Piston ball (25) is not seating Service piston ball. Manual 308798. Piston packings are worn or damaged Replace packings. Manual 308798. O-ring (227) in displacement pump is worn or damaged Replace o-ring. Manual 308798. Intake valve ball is not seating prope ...

  • Graco Inc. 232631 - page 7

    308870 7 Rollers Removal 1. Relieve pressure ; page 4. 2. Fig. 2. Remove six cap screws (10) lock washers (9) and cover assembly (24). Note: A screw driver may be needed to pry off cover assembly . 3. Remove dowel pins (97) and rollers (98) Installation 1. Install rollers (98) and dowel pins (97) 2. Install cover assembly (24) with six lock washers ...

  • Graco Inc. 232631 - page 8

    308870 8 Cam Follower Bearings Removal 1. Relieve pressure ; page 4. 2. Fig. 16. Cycle pump piston rod (222) to lowest position. T urn engine off. 3. Fig. 4. Remove six cap screws (10), lock washers (9) and cover assembly (24). Note: A screw driver may be needed to pry off cover assembly . 4. Remove four dowel pins (97) and rollers (98). 5. From fr ...

  • Graco Inc. 232631 - page 9

    308870 9 Pinion Assembly/Rotor/Field/Shaft/Clutch Removal If pinion assembly (19) is not removed from clutch housing (5), do 1. through 4. Otherwise, start at 5. 1. Relieve pressure ; page 4. 2. Disconnect field cable (X) from pressure control and engine lead. 9027A Fig. 5 X Bottom View 3. Fig. 6. Remove five screws (26) and lockwashers (17) and pi ...

  • Graco Inc. 232631 - page 10

    308870 10 Pinion Assembly/Rotor/Field/Shaft/Clutch Installation 1. Fig. 10. Lay two stacks of two dimes on smooth bench surface. 2. Lay armature (4a) on two stacks of dimes. 3. Press center of clutch down on bench surface. Fig. 10 4a 8705A 0.12 ± .01 in. (3.0 ± .25 mm) 4. Install armature (4a) on engine drive shaft. 5. Install four screws (16) an ...

  • Graco Inc. 232631 - page 11

    308870 11 Clutch Housing Removal 1. Fig. 12. Remove four capscrews (75) and lock- washers (77) which hold clutch housing (5) to engine. 2. Remove screw (15) from under mounting plate (D). 3. Remove engine key (7). 4. Pull of f clutch housing (5). Installation 1. Fig. 12. Push on clutch housing (5). 2. Install four capscrews (75) and lockwashers (77 ...

  • Graco Inc. 232631 - page 12

    308870 12 On/Off Switch Removal 1. Relieve pressure ; page 4. 2. Fig. 15. Remove five screws (307) and cover (322). 3. Disconnect two wires (A) from ON/OFF switch (309). 4. Press in on two retaining tabs on each side of ON/OFF switch (309) and remove switch. Installation 1. Install new ON/OFF switch (309) so tabs of switch snap into place on inside ...

  • Graco Inc. 232631 - page 13

    308870 13 Pressure Control Control Board Removal 1. Relieve pressure ; page 4. 2. Fig. 15. Remove five screws (307) and cover (322). 3. Fig. 22. Disconnect at control board (302): D Four clutch leads: two violet and two black. D Lead (D) from potentiometer . D Lead (E) from transducer . D T wo red leads (A) to ON/OFF switch (309). 4. Fig. 15. Re mo ...

  • Graco Inc. 232631 - page 14

    308870 14 Pressure Control Control Board Diagnostics 1. Fig. 15. Remove five screws (307) and cover (322). 2. Start sprayer . 3. T urn ON/OFF switch ON. 4. Observe LED operation and reference following table: LED BLINKS SPRA YER OPERA TION INDICA TES WHA T TO DO T wo times repeatedly Sprayer shuts down and LED contin- ues to blink two times repeate ...

  • Graco Inc. 232631 - page 15

    308870 15 Displacement Pump Removal 1. Flush pump. 2. Fig. 16. Cycle pump with piston rod (222) in lowest position. 3. Relieve pressure ; page 4. 4. Fig. 16. Remove suction tube (30) and hose (33). 9024B Fig. 16 222 33 30 9024C 5. Fig. 17. Use screwdriver to push out pump pin (101). Fig. 17 101 20a Detail A 9019B 6. Fig. 18. Loosen locknut by hitti ...

  • Graco Inc. 232631 - page 16

    308870 16 Displacement Pump Pump Pin Clip Removal 1. Remove pump (28). 2. Remove two bolts (86), washers (25), pump brack- et (85), pail hook (94) and shield (95). 3. Fig. 17. Remove clip (230). Installation 1. Fig. 17. Install clip (230). 2. Install shield (95), pail hook (94) and pump bracket (85) with two washers (25) and bolts (86). T orque bol ...

  • Graco Inc. 232631 - page 17

    308870 17 Parts List & Drawing – Pinion Assembly Ref No. 19 and 20 Ref No. 19: Pinion Housing Assembly 241 1 16 Ref No. 20: Drive Housing Assembly 241537 Ref No. Part No. Description Qty Ref No. Part No. Description Qty 19a 241 121 PINION HOUSING, COIL 1 19b 105489 PIN 2 19d 241 1 14 PINION SHAFT 19e 1 12770 RET AINING RING, large 20 DRIVE HO ...

  • Graco Inc. 232631 - page 18

    308870 18 Parts Drawing – Hi-Boy Sprayers 9018D 9027A Ref 1 1 40 45 37 38 39 Ref 35 DET AIL A 52 Model 232630 See manual 308798 for the parts. 1 2 3 Label See page 17 for the parts. 1 5 18 19 10 98 24 97 9 20 2 2 4a 94 101 28 21 25 80 43 41 42 4 See page 22 for the parts. 52 12 11 86 DET AIL A 44 3 2 85 95 16 17 7 8 73 15 71 17 16 72 17 4b 70 64 ...

  • Graco Inc. 232631 - page 19

    308870 19 Parts List – Hi-Boy Sprayers Models 232630* Ref No. Part No. Description Qty Ref No. Part No. Description Qty 1 1 14530 ENGINE 1 2 1 13084 RIVET , blind 2 3 192014 PLA TE, indicator 1 4 241 1 13 CLUTCH ASSEMBL Y ,1 includes 4a, 4b, 16, 17, 72, 80 4a .ARMA TURE, clutch, 5 in. 1 4b .ROT OR, 5 in. 1 5 193531 CLUTCH HOUSING 1 7 183401 KEY , ...

  • Graco Inc. 232631 - page 20

    308870 20 9027A 30f Ref 1 1 40 45 37 39 51 Ref 35 DET AIL A Model 232632 See manual 308798 for the parts. 1 2 3 Label See page 17 for the parts. 1 5 19 9 98 101 97 99 20 2 2 3 4a 94 25 28 24 80 9 10 43 41 42 33 4 See page 22 for the parts. 52 12 11 62 DET AIL A 44 3 2 85 16 17 17 26 7 8 73 77 15 71 17 16 4 72 17 4b 35 30e 62 102 30c 30b 30a 71 30d ...

  • Graco Inc. 232631 - page 21

    308870 21 Parts List – Lo-Boy Sprayers Model 232632 Ref No. Part No. Description Qty Ref No. Part No. Description Qty 1 1 14530 ENGINE 1 2 1 13084 RIVET , blind 2 3 192014 PLA TE, indicator 1 4 241 1 13 CLUTCH ASSEMBL Y ,1 includes 4a, 4b, 16, 17, 72, 80 4a .ARMA TURE, clutch, 5 in. 1 4b .ROT OR, 5 in. 1 5 193531 CLUTCH HOUSING 1 7 183401 KEY , p ...

  • Graco Inc. 232631 - page 22

    308870 22 Parts Drawing – Sprayer Models 232630 through 232633 318k 318j 318l 307 322 305 310 31 1 306 315 318z 318aa 303 302 309 308 312 310 313 314 304 305 301 307 304 318c 318a 318b 318d 318e 318f 8716A 319 321 320 318n 318m 318h 318g 323 ...

  • Graco Inc. 232631 - page 23

    308870 23 Parts List – Sprayer Models 232630 through 232633 REF NO. P ART NO. DESCRIPTION QTY REF NO. P ART NO. DESCRIPTION QTY 30 1 193653 PLA TE, control 1 302 241093 BOARD, PC 1 30 3 1 1 1839 SCREW , mch pan, 6 – 32 x 1/2 in. 5 304 240776 HARNESS, wiring. 1 30 5 193497 GASKET , control 2 306 193652 HOUSING, control box 1 307 1 14631 SCREW , ...

  • Graco Inc. 232631 - page 24

    308870 24 Parts List & Drawing – Complete Sprayers Models 232631, 232633 Includes items 201 to 204 Ref No. Part No. Description Qty 201 232631 Hi-Boy Sprayer 1 See parts list on page 18 232633 Lo-Boy Sprayer 1 See parts list on page 21 202 240797 HOSE, grounded, nylon; 3/8 in. ID; 1 cpld 3/8 npsm(fbe); 50 foot (15 m); spring guards both ends ...

  • Graco Inc. 232631 - page 25

    308870 25 T echnical Data Honda GX160 Engine Power Rating @ 3700 rpm ANSI 5.5 Horsepower . . . . . . . . . . . . . . . . . . . . . . . DIN 6270B/DIN 6271 NA 2.9 Kw – 4.0 Ps . . . . . . . . . . . . . . . . . . . . . . NB 3.6 Kw – 4.9 Ps . . . . . . . . . . . . . . . . . . . . . . Maximum working pressure 3300 psi . . . . . . . . . . . . . . . (2 ...

  • Graco Inc. 232631 - page 26

    308870 26 Graco W arranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by a n authorized Graco distributor to the original purchaser for use. With the exception of any special, extended , or limited warranty published by Graco, Graco will, for a perio ...

メーカー Graco Inc. カテゴリー Paint Sprayer

Graco Inc. 232631のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 232631の取扱説明書
- Graco Inc.の製品カード
- パンフレット
- またはGraco Inc. 232631の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco Inc. 232631の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco Inc. 232631の取り付け説明書、サービスマニュアル、簡易説明書、またはGraco Inc. 232631のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco Inc. 232631の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco Inc. 232631デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco Inc. 232631を使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco Inc. 232631ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Graco Inc.の取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco Inc. 232631の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco Inc. 232631の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco Inc. 232631に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco Inc. 232631デバイスの基本機能を使うにあたってのヒント。 Graco Inc. 232631のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco Inc. 232631に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco Inc. 232631のメーカー/サービスへの連絡先に関する情報。

Graco Inc. 232631についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもGraco Inc. 232631の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco Inc. 232631で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)