RuggedCom I800の取扱説明書

21ページ 0.56 mb
ダウンロード

ページに移動 of 21

Summary
  • RuggedCom I800 - page 1

    R uggedSwitch ™ i 800 F amily Installa tion Guide www.ruggedcom.com ...

  • RuggedCom I800 - page 2

    Copyright COPYRIGHT © 2008 RuggedCom Inc. ALL RIGHTS RESERVED Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registratio n. Th ...

  • RuggedCom I800 - page 3

    Federal Communications Commission Radio Frequency Interference S t atement This equipment has be en tested and found t o comply with the limits for a Cla ss A digital devic e pursuant to Part 15 of the FCC Rules. These limits are desi gned to provi de reasonable protection agai nst harmful interfer ence when the equipment i s operated in a commerci ...

  • RuggedCom I800 - page 4

    Table of Contents T able of Content s Federal Communications Commission Radio Frequency Interference Statement .. 3 Table of Contents ............................................................................................................ 4 Table of Figures ........................................................................................ ...

  • RuggedCom I800 - page 5

    Product Overview 1 Product Overview 1.1 Functional Overview The RuggedSwitch™ i 800, or i -Series, is a family of compact, fully managed Ethernet switches designed to operate reliably in harsh industrial environments. The flexibility of the i 800 family allows the user to choose from managed or unmanaged, regular or extended temperature, and a mi ...

  • RuggedCom I800 - page 6

    Product Overview 1.3 i 800 Family Front Panel View Figure 1: Front Panel The front panel shown is representative of the i 800 family. Note that there are several Ethernet options available in several models, outlined in Section 1.3.2 , below. Fail-Safe Relay Power LEDs Power Connecto r RS-232 Console Port Ports 1 – 4/6/8: 10/100 BaseTx Memory Slo ...

  • RuggedCom I800 - page 7

    Product Overview 1.3.1 Front Panel LEDs ITEM Color Activity Comments Power status Green Solid Power On Alarm status Red Solid Alarm condition exists Blinking Link Established Fiber port status Yellow Solid Tx/Rx Activity RJ45 Speed Yellow Solid 100Mbps Solid Link Established RJ45 Link/Act Yellow Blinking Tx/Rx Activity Table 1: Status LEDs Note tha ...

  • RuggedCom I800 - page 8

    Product Overview 1.4 i 800 Family Top Panel View Figure 2: Top Panel For details on connecting the power supplies an d Ground, see Section 2.2 . For details on connecting the Fail-Safe Relay, see Section 2.3 Ratings : 12 - 24V , , 2A P1+ P1- GND P2- P2+ Fail-Safe Relay Power Connecto r back front DIN Rail mounting bracket Chassis Ground RuggedCom® ...

  • RuggedCom I800 - page 9

    Product Overview 1.5 i 800 Family Bottom Panel View Ports 5-7, 7&8, or 9: Ports 1 – 4/6/8: 10/100/1000Base Tx, 100FX, 1000SX/LX 10/100Base Tx Figure 3: Bottom Panel For details on connecting the console port, see Section 2.4 . For a description of the memory slot, see Section 2.6 . RS-232 Console Port Micro-SD Memory Slot back front CONSOLE 5 ...

  • RuggedCom I800 - page 10

    Installation 2 Inst allation 2.1 DIN Rail Mounting The i 800 family of switches comes with a standard DIN rail mounting bracket. Figure 4 details the mounting configuration for a standard 1” DIN Rail. DIN Rail Power 2 i 802 Figure 4: DIN Rail Mounting Power 1 R 3 1 4 2 56 7 8 Alarm Release direction DIN Rail mounting bracket RuggedCom® 10 Rugged ...

  • RuggedCom I800 - page 11

    Installation 2.2 Power Supply Wiring and Grounding Ratings : 12 - 24V , , 2A P1+ P1- GND P2- P2+ back front DC In p ut 1 DC In p ut 2 Chassis Ground Figure 5: DC Power supply and ground connec tions The low voltage DC power supply features reverse polarity protection and dual independent inputs, allowing the connection of two DC sources with the sa ...

  • RuggedCom I800 - page 12

    Installation Figure 6 illustrates the connections required for both single and dual power supply configurations: Ratings : 12-24V , , 2A Figure 6: Power Supply Wiring Examples NOTES: • Connect to the DC inputs according to the polarity markings on the unit. • Chassis Ground must be connected to the protective earth. • The internal connection ...

  • RuggedCom I800 - page 13

    Installation 2.3 Failsafe Output Wiring The Failsafe output relay is provided via a Phoenix connector to signal critical error conditions that may occur on the unit. The contacts are en ergized upon power up of the unit and remain energized until a critical alarm condition or power loss occur s. A common application for this output is to signal an ...

  • RuggedCom I800 - page 14

    Installation 2.4 RS232 Console Port Wiring The RS232 Console Port is used for initially configuring the unit. The connection is made using a DB9-Female to RJ45 console cable with the pin-outs listed in Table 5 . Pin 1 Pin 8 Figure 8: RS232 Female DCE pin-out RuggedCom RS232 over RJ45 pin-out specification Signal Name (PC is DTE) DB9- Female RJ45 Ma ...

  • RuggedCom I800 - page 15

    Installation 2.5 RJ45 Ports – Signal Description 10/100Base-TX ports allow connection to standard Category 5 (CAT-5) unshielded twisted-pair (UTP) cable with RJ45 male connectors. The RJ45 receptacles are directly connected to the chassis ground on the unit and can accept CAT-5 shielded twisted-pair (STP) cables. If shielded cables are used, care ...

  • RuggedCom I800 - page 16

    Installation 2.6 Memory Slot The i 800 family of switches feature a remov able microSD memory module to support the following features: • Configuration update and backup • Redundant firmware image • Greatly expanded logging capability • Fault-tolerant firmware update In case of unit failure, remove power from the unit and unplug any attache ...

  • RuggedCom I800 - page 17

    Technical Specifications 3 T echnical Specifications 3.1 Type Test Specifications IEC 61000-6-2 EMC: Generic Stand ards - Immunity for industrial environments Test Description Levels Enclosure Contact +/- 4kV IEC 61000-4-2 ESD Enc losure Air +/- 8kV IEC 61000-4-3 Radiated RFI Enclosu re ports 10 V/m, 80 to 1000Mhz Signal ports +/- 1kV @ 5k Hz IEC 6 ...

  • RuggedCom I800 - page 18

    Technical Specifications 3.2 Environmental Specifications Parameter Range Comments Ambient Operating Tempera ture -20 to 60 ° C -40 to 85 ° C (Optional) Ambient Temperature as measured from a 30 cm radius surrounding the center of the enclosure. Ambient Storage Tempera ture -40 to 85 ° C Ambient Relative Humidity up to 95% Non-conden sing, 55 ° ...

  • RuggedCom I800 - page 19

    Technical Specifications 3.5 RJ45 Ethernet Port Specifications Data Port Medi a Distance Connector Type 10/100 Mbps CAT-5 UTP or STP 100m RJ45 Table 13: RJ45 Ethernet Port Specific ations 3.6 Fiber Optic Port Specifications Order Code Speed Standard Mode / Connecto r Tx (nm) Cable Type (um) _FG01 1000SX MM/LC 850 62.5/125 _FG03 1000LX SM/LC 1310 9/ ...

  • RuggedCom I800 - page 20

    Technical Specifications 3.7 Physical Dimensions Power 1 Power 2 i 802 CONSOLE 57600-N-8-1 MEMORY SLOT 4.625 2.225 3.750 3.918 5.296 0.460 3.050 0.246 0.833 3.833 4.421 3 1 4 2 56 7 8 Alarm R 3.490 3.918 NOTE: All dimensions are in inches. Figure 10: Mechanical Specifications Parameter Value Comments Dimensions 4.625 x 2.25 x 3.75 inches (117 x 57 ...

  • RuggedCom I800 - page 21

    Warranty RuggedSwitch™ i 800 family 21 RuggedCom® 3.8 Agency Approvals Agency Standards Comments Status ATEX Zone 2 Gas, Vapor, or Du st environmental Pending FCC FCC Part 15, Class A Emissions Approved EN/CISPR EN55022 (CISPR22), Class A Emissions Approved FDA/CDRH 21 CF R Chapter 1, Subchapter J Laser Eye Safety Pending ISO ISO9001:2000 Design ...

メーカー RuggedCom カテゴリー Switch

RuggedCom I800のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- I800の取扱説明書
- RuggedComの製品カード
- パンフレット
- またはRuggedCom I800の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、RuggedCom I800の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、RuggedCom I800の取り付け説明書、サービスマニュアル、簡易説明書、またはRuggedCom I800のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、RuggedCom I800の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

RuggedCom I800デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRuggedCom I800を使用するのを助ける技術的文書のことです。説明書は通常、全てのRuggedCom I800ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

RuggedComの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. RuggedCom I800の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRuggedCom I800の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。RuggedCom I800に関してこのドキュメントで見つけることができる全てのヒントの目次
3. RuggedCom I800デバイスの基本機能を使うにあたってのヒント。 RuggedCom I800のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。RuggedCom I800に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRuggedCom I800のメーカー/サービスへの連絡先に関する情報。

RuggedCom I800についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRuggedCom I800の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRuggedCom I800で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)