Thermador P30の取扱説明書

44ページ 2.26 mb
ダウンロード

ページに移動 of 44

Summary
  • Thermador P30 - page 1

    Pour toutes cuisinières à gaz Thermador Professional ® PRO-HARMONY™ INSTRUCTIONS D’INST ALLA TION For Thermador Professional ® PRO-HARMONY™ Gas Ranges INST ALLA TION INSTRUCTIONS Models P30 P36 ...

  • Thermador P30 - page 2

    IMPORTANT: Save these instructions for the Local Gas Inspector’s use. INSTALLER: Please leave these Installation Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Please Read Entire Instructions Before Proceeding For Massachusett s Installations: 1. Installation must be performed by a qualifi ...

  • Thermador P30 - page 3

    Contents Important Installation Information ................. 1 Step 1: Ventilation Requirements ................ 2 Step 2: Cabinet Preparation ................. 3 – 7 Step 3: Unpacking, Moving and Placing the Range ......................... 8 – 9 Step 4: Installing Anti-Tip Device ...... 10 – 11 Step 5: Gas Requirements and Hookup .... 12 St ...

  • Thermador P30 - page 4

    Important Inst allation Information GAS type verification Verify the type of gas supplied to the location. Ensure that the appliance is connected to the type of gas for which it is certified. Ranges are certified for use with only natural gas or propane (LP) gas. Make certain the range matches the gas type available; these ranges are NOT convertibl ...

  • Thermador P30 - page 5

    S tep 1: V entilation Requirements It is strongly recommended that a suitable exhaust hood be installed above the range. Downdraft ventilation should not be used. The table below indicates the Thermador hoods, by model number, that are recommended for use with all ranges. 1 . Select Hood and Blower Models: • For wall installations, the hood width ...

  • Thermador P30 - page 6

    3 S tep 2: Cabinet Preparation 1. The range is a free standing unit. If the unit is to be placed adjacent to cabinets, the clearances shown in Fig. 1 are required. The same clear- ances apply to island installations, except for the overhead cabinets, which must have a space wide enough to accept the flared island hood, as indicated in Fig. 1. 2. Th ...

  • Thermador P30 - page 7

    4 S tep 2: Cabinet Preparation For Electrical and Gas Supply Zone, see Figure 3A. Zone size and position differ according to the model. Cooking Surface CAUTION: See Figs. 2A, and 2B. 40" Min. to combustible material , from cooking surface as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). *The range height is adjust ...

  • Thermador P30 - page 8

    40" min. to combustibles combustible materials 3" island trim 12" min. to combustibles with island trim front face 36 3/4" max. 35 7/8" min. 22" 36 3/4" max. 35 7/8" min. 40" min. to combust- ibles Low Back Guard High Shelf 6" (P304) 9" (P36) combustible materials 27 5/8" 26 1/2" 10 3 ...

  • Thermador P30 - page 9

    6 GAS AND ELECTRIC SUPPL Y S tep 2: Cabinet Preparation FIG. 3A Gas & Electrical Supply Locations for All Gas Ranges The All Gas ranges may be connected to the power supply with a range supply cord (supplied with range) or by hard-wiring to the power supply. It is the responsibility of the installer to provide the proper wiring components (cord ...

  • Thermador P30 - page 10

    S tep 2: Cabinet Preparation ELECTRICAL SUPPLY, ALL GAS RANGES 7 FIG. 3B Wall Connection Power Cord & Receptacle Installation of the range must be planned so that the rough-in of the junction box for the receptacle will allow maximum clearance to the rear of the unit. To minimize binding when the unit is connected to the receptacle or junction ...

  • Thermador P30 - page 11

    Chart A 30" Range 36" Range Shipping Weight 300 lbs. 335 lbs. Weight without 265 lbs. 300 lbs. packing materials Without door(s), 142 lbs. 207 lbs . burner caps, front kick panel and oven racks 8 S tep 3: Unpacking, Moving and Placing the Range CAUTION Proper equipment and ad- equate manpower must be used in moving the range to avoid inju ...

  • Thermador P30 - page 12

    9 • Due to the weight, a dolly with soft wheels should be used to move this unit. The weight must be supported uniformly across the bottom (See Fig. 5). • After transporting the professional range by dolly close to its final location, the range can be tipped back and supported on the rear legs while the dolly is carefully removed. THE FLOOR UND ...

  • Thermador P30 - page 13

    10 S tep 4: Installing Anti-T ip Device T ools Needed for Inst allation of Anti-Tip Device: • Screwdriver, Phillips • Hammer • Drill, electric or hand • Pencil or other marker • Measuring tape or ruler • 1/8" drill bit (wood or metal wall or floor) • 3/16" carbide-tipped masonry drill bit (concrete or concrete block wall or ...

  • Thermador P30 - page 14

    11 S tep 4: Installing Anti-T ip Device 30" and 36" Ranges (Figures 6 and 7) Thermador Service Part No. Qty. Description 415078 4 Screw, Phillips, #10 x 1-1/2" 600413 1 Anti-Tip Bracket, Floor-Mounted IMPORTANT INSTALLATION INFORMATION: • The anti-tip bracket may be attached to a solid wood cabinet having a minimum wall thickness o ...

  • Thermador P30 - page 15

    12 S tep 5: Gas Requirements and Hookup Verify the type of gas being used at the installation site. As shipped from the factory, units are configured for use with only natural gas or propane (LP) gas. Make certain the range matches the type of gas available at this location. These ranges are NOT convertible between different types of gas . For inst ...

  • Thermador P30 - page 16

    13 S tep 6: Electrical Requirements, Connection & Grounding • Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally. • For these gas range models, a neutral supply wire must be provided from the power source (breaker/fuse panel) because critical range com- ponents, incl ...

  • Thermador P30 - page 17

    14 S tep 7: Backguard Installation 6” or 9” LOW BACK: 6” Low Back – included with 30” Pro Harmony Gas Range. Model GP36LB , 9” tall – for 36” Pro Harmony Gas Ranges. 22” High POT-and-PAN SHELF: Model GP30HS – for 30” Pro Harmony Gas Range. Model GP36HS – for 36” Pro Harmony Gas Ranges. 3” ISLAND TRIM: Model GP30IT – fo ...

  • Thermador P30 - page 18

    15 S tep 8: Door Removal and Reinstallation Photo B. Hinge bracket in closed position T o Remove the Oven Door: 1. Fully open the oven door . 2. Flip the hinge clip toward you (see illustration at right). 3. Close the door until it stops (the open hinge clip will hold the door about halfway open. 4. Grasp the door on the sides. The door is heavy an ...

  • Thermador P30 - page 19

    16 S tep 9: Burner T est and Adjustment WHEN FLAME IS PROPERL Y ADJUSTED: There should be a flame at each burner port. There should be no air gap between the flame and burner port. Install any loose components, such as burner caps and grates, that may have been removed earlier. Be certain that burner caps seat properly into the burner bases. Before ...

  • Thermador P30 - page 20

    T est Oven Burners Remove the oven bottom cover. Remove the 4 screws on the sides and the 2 screws on the back, then slide the cover forward while lifting to clear the angled baffle plate mounted to the bottom of the cover. Test Bake Burner Ignition Set the oven to BAKE at 350°F. After 30-75 seconds, the burner will ignite. The burner will stay li ...

  • Thermador P30 - page 21

    INST ALLER CHECKLIST ❑ The appliance is connected only to the type of gas for which it is certified for use. ❑ Manual gas shut off valve in- stalled in an accessible loca- tion (without requiring removal of range). ❑ Unit tested and free of gas leaks. ❑ Gas supply pressure does not exceed 14" W.C. (34.9 mb). ELECTRICAL ❑ Receptacle w ...

  • Thermador P30 - page 22

    NOTES ...

  • Thermador P30 - page 23

    Pour les inst allations au Massachusett s : 1 . L ’installation doit être réalisée par un entrepreneur qualifié ou agréé, un plombier ou un installateur de gaz qualifié ou autorisé par l’État ou la région dans laquelle cet appareil est installé. 2. Le robinet d’arrêt de gaz doit être pourvu d’une poignée en « T ». 3. La long ...

  • Thermador P30 - page 24

    T able des matières Informations importantes à propos de l'installation .......... 1 Chapitre 1 : Exigences pour la ventilation ....................... 2 Chapitre 2 : Préparation de l’emplacement ............... 3 – 7 Chapitre 3 : Déballage, manutention et mise en place de la cuisinière ........................................... 8 ? ...

  • Thermador P30 - page 25

    1 Cet appareil a été testé conformément à la norme américaine ANSIZ21.1 pour les appareils électroménagers de cuisson au gaz et à la norme canadienne CAN 1.1-M81 sur les cuisinières à gaz domestiques. On recommande fortement d’installer une hotte de ventilation adaptée au-dessus de cet appareil (voir Chapitre 1, Conditions de ventilat ...

  • Thermador P30 - page 26

    Chapitre 1 : Exigences pour la ventilation Il est fortement recommandé d’installer une hotte de ventilation appropriée au- dessus de la cuisinière. Une ventilation par contre-tirage ne devrait pas être utilisée. Le tableau ci-dessous énumère, par numéro de modèle, les hottes Thermador que l'on conseille d’utiliser avec les cuisini ...

  • Thermador P30 - page 27

    3 Chapitre 2 : Préparation de l’emplacement 1 . La cuisinière est un appareil monobloc. Si elle est placée au milieu des armoires, les dégagements requis sont indiqués à la Figure 1. Les mêmes dégagements s’appliquent aux installations en îlot, excepté pour les armoires suspendues qui doivent laisser un espace suffisamment grand pour ...

  • Thermador P30 - page 28

    4 Chapitre 2 : Préparation de l’emplacement Zone d’arrivée d’électricité et de gaz (voir Fig. 3A). Les dimensions et la position de cette zone varien selon le modèle. Table de cuisson MISE EN GARDE : Voir Fig. 2A et 2B. Distance min. de 101,6 cm (40") entre la table de cuisson et les matériaux combustibles . Tel que défini dans le ...

  • Thermador P30 - page 29

    22po 36 3/4po max. 35 7/8po min. Min. 40 po aux com- bustibles Dosseret bas T ablette haute 6po (P304) 9po (P36) Matériaux combustibles 27 5/8 po 26 1/2 po 10 3/4po 2 1/4po 24 5/8po 23 7/8po max . 24 3/4po 22 1/2po Devant Mur 5 Chapitre 2 : Préparation de l’emplacement Min. 40 po aux combustibles Matériaux combustibles 3 po Garniture pour îlo ...

  • Thermador P30 - page 30

    La cuisinière à gaz peut être branchée sur l'alimentation électrique avec un cordon d'alimentation pour cuisinière (fourni avec l'appareil) ou par un câblage fixe à l'alimentation. Il incombe à l'installation de fournir les composants appropriés pour le câblage (cordon ou cuiduit et fils) et de compléter la conn ...

  • Thermador P30 - page 31

    Chapitre 2 : Préparation de l’emplacement Alimentation électrique pour toutes les cuisinières au gaz 7 Cordon d’aliment ation et prise 2 1/4 po max. une fois branché FIG . 3B – RACCORDEMENT AU MUR L’installation des cuisinières à gaz doit être planifiée de sorte que la boîte de dérivation pour la prise laisse le maximum d’espace ...

  • Thermador P30 - page 32

    Tableau A Cuisinière de Cuisinière de 76,2 cm (30 po) 91,4 cm (36 po) Poids à l’expédition 300 lb 335 lb Poids sans matériaux 265 lb 300 lb d’emballage Poids hors porte(s), 142 lb 207 lb chapeaux de brûleurs, plaque d’habillage et grilles de four 8 Chapitre 3 : Déballage, manutention et mise en place de la cuisinière Un équipement ad ...

  • Thermador P30 - page 33

    9 Chapitre 3 : Déballage, manutention et mise en place de la cuisinière FIG. 5 - Mise en place sur la plate-forme à roulettes Le poids de la cuisinière doit être uniformément réparti en s’aidant des supports placés sur le dessous de la cuisinière • En raison du poids de la cuisinière, il convient d’utiliser une plate-forme à roulet ...

  • Thermador P30 - page 34

    10 Chapitre 4 : Installation du dispositif antibascule Outils nécessaires pour l’inst allation du dispositif antibascule : • T ournevis Phillips • Perceuse électrique ou manuelle • Ruban à mesurer ou règle • Foret de 3,2 mm (1/8") (mur ou sol en bois ou métal) • Foret à béton pointe carbure de 4,8 mm (3/16") (mur ou sol ...

  • Thermador P30 - page 35

    11 Chapitre 4 : Installation du dispositif antibascule Cuisinières à gaz de 30 po et 36 po (Figures 6 et 7) Référence pièce détachée Thermador Quantité Description 415078 4 Vis Phillips n o 10 3,81 cm (1-1/2 po) 600413 1 P atte antibascule, montage au sol • La patte antibascule peut être fixée à une armoire en bois massif ayant une par ...

  • Thermador P30 - page 36

    12 Chapitre 5 : Exigences de l'alimentation du gaz et raccordement Photo A Exigences pour le gaz naturel : Raccord d’entrée :1/2" NPT interne (tuyau flexible 19,1 mm (3/4") diamètre min.) Pression d’alimentation :14,9 mb (6") min. à 34,9 mb (14") max. C.E. Pression du collecteur :12,5 mb (5") C.E. Exigences pour ...

  • Thermador P30 - page 37

    13 Chapitre 6 : Exigences pour l’alimentation électrique, le branchement et la mise à la terre • Avant d’intervenir sur l’appareil, débranchez toujours le cordon d’alimentation électrique de la prise murale. V errouiller le panneau de service pour empêcher la mise en circuit accidentelle. A TTENTION L’appareil doit être isolé du ...

  • Thermador P30 - page 38

    14 Chapitre 7 : Installation du dosseret MODÈLE BAS 6 OU 9 PO : Modèle bas 6 po – compris avec la cuisinière à gaz Pro Harmony 30 po. Modèle GP36LB – 9 po de haut ; pour cuisinières à gaz Pro Harmony 36 po. TABLETTE POUR CASSEROLES 22 PO DE HAUT : Modèle GP30HS – pour cuisinière à gaz Pro Harmony 30 po. Modèle GP36HS – pour cuisi ...

  • Thermador P30 - page 39

    15 Chapitre 8 : Retrait et installation de la porte (Retain for future door removal) Photo B. Charnière en position fermée Retrait de la porte : 1 . Ouvrir complètement la porte 2. Abaisser la pince vers soi (voir illustration à droite). 3 . Fermer la porte jusqu'à ce qu'elle arrête (la pince ouverte maintient la porte à mi-chemin) ...

  • Thermador P30 - page 40

    16 Chapitre 9 : T est et réglage de brûler Installer tout composant lâche, tels capuchons et grilles de brûleurs, ayant été retirés précédemment. S'assurer que les capuchons de brûleurs sont adéquatement placés sur les bases des brûleurs. Avant de vérifier le fonctionnement de l'appareil, vérifier qu'il n'y a aucu ...

  • Thermador P30 - page 41

    17 Chapitre 9 : T est et réglage de brûler Réglage de flamme (au besoin): Le brûleur tube utilisé avec les appareils Thermador© sont dotés de système d'obturateur d'air semblables à l'illustration, figure 10, et peut être réglé à l'aide de la méthode suivante (à moins que le réglage ne soit pas recommandé). Il e ...

  • Thermador P30 - page 42

    Liste de vérification pour l’installateur ALIMENT A TION EN GAZ ❑ Raccord : filetage NPT de 1/2 po avec tuyau flexible diamètre minimum 19,1 mm (3/ 4 po) d'environ 4 pi de long selon les codes locaux. ❑ L ’appareil est bien raccordé au type de gaz pour lequel il est certifié. ❑ Le robinet manuel d’arrêt de gaz a été install? ...

  • Thermador P30 - page 43

    REMARQUES ...

  • Thermador P30 - page 44

    S pecifications are for planning purposes only . Refer to installation instructions and consult your countertop supplier prior to making counter opening. Consult with a heating and ventilating engineer for your specific ventilation requirements. For the most detailed information, refer to installation instructions accompanying product or write Ther ...

メーカー Thermador カテゴリー Range

Thermador P30のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- P30の取扱説明書
- Thermadorの製品カード
- パンフレット
- またはThermador P30の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Thermador P30の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Thermador P30の取り付け説明書、サービスマニュアル、簡易説明書、またはThermador P30のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Thermador P30の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Thermador P30デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがThermador P30を使用するのを助ける技術的文書のことです。説明書は通常、全てのThermador P30ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Thermadorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Thermador P30の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははThermador P30の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Thermador P30に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Thermador P30デバイスの基本機能を使うにあたってのヒント。 Thermador P30のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Thermador P30に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるThermador P30のメーカー/サービスへの連絡先に関する情報。

Thermador P30についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもThermador P30の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがThermador P30で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)