Makita DPC7321HDの取扱説明書

32ページ 2.81 mb
ダウンロード

ページに移動 of 32

Summary
  • Makita DPC7321HD - page 1

    1 W ARNING! Read and understand this Manual. Always follow safety precautions in the Instruction and Safety Manual. Improper use can cause serious injury! The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm. Preserve this Manual carefully! Instruction an ...

  • Makita DPC7321HD - page 2

    2 EMISSIONS COMPONENT DEFECT W ARRANTY COVERAGE MAKIT A U.S.A, Inc warrant to the initial retail purchaser and each subsequent owner , that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EP A), and that the engine is free of d ...

  • Makita DPC7321HD - page 3

    3 T able of contents Page Packing ................................................................................ 3 Delivery inventory .............................................................. 4 Symbols ............................................................................... 4 SAFETY PRECAUTIONS Intended use ........................... ...

  • Makita DPC7321HD - page 4

    4 5 4 3 2 1 Symbols Y ou will notice the following symbols on the saw and in the Instruction Manual: In case one of the parts listed should not be included in the delivery inventory , please consult your sales agent. Delivery inventory 1. Power Cut 2. Cutting disc 3. Screwdriver (for carburetor adjustment) 4. Offset screwdriver 5. Universal wrench ...

  • Makita DPC7321HD - page 5

    5 F E 2 3 1 4 SAFETY PRECAUTIONS Intended use Power Cut Use the Power Cut cutof f saw outdoors only , for trimming and cutting suitable materials, using cutting discs rated for this machine. Improper use: Never use the cutoff saw cutting discs for grinding or sanding (using the side of the cutting disc to remove material). The disc can break! Never ...

  • Makita DPC7321HD - page 6

    6 H G 7 6 5 9 8 30 m (100 feet) 3 meters (10 feet) = w e ar i ng P ro t ec t iv e E q ui p m en t - Always wear safety shoes or boots (G) with steel toes, non-skid soles, and leg protectors when working with the Power Cut. Safety shoes equipped with a protective layer provide protection against cuts and ensure a secure footing. - Always wear a work ...

  • Makita DPC7321HD - page 7

    7 10 1 1 13 12 14 ● Maintenance ● Refuelling ● Changing cutoff discs ● Repositioning the cutting attachment ● Stopping work ● T ransport ● Putting out of function S T O P min. 5 m (16 feet) Cu to ff di sc s - The pr ote cti on hoo d mus t alw ay s be on ! Ch ang e di scs on ly wi th the en gin e o ff! - The re are tw ...

  • Makita DPC7321HD - page 8

    8 18 16 17 15 Kickback and lock-in - When working with the Power Cut there is a danger of kickback and lock-in. - Kickback occurs when the top of the cutting disc is used for cutting (15). - This causes the Power Cut to be thrown back toward the user with great force and out of control. Risk of injury! T o prevent kickback, observe the following: - ...

  • Makita DPC7321HD - page 9

    9 19 20 21 Whe n usin g syn the tic r esi n cut tin g discs , a lwa ys ob - ser ve the f oll owing : CAU TIO N : - Synth etic resin cu tti ng dis cs can abso rb moist ure. This moi stu re can ca use the disc t o becom e unb alanc ed at hig h spe ed. This im balanc e can ca use t he dis c to bre ak. - Do no t coo l r esin cut tin g dis cs wit h wat ...

  • Makita DPC7321HD - page 10

    10 23 26 25 24 In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water . MAKIT A offers the right accessories for all wet cutting applications (see also "SPECIAL ACCESSORIES"). - Remove foreign objects such as sand, stones and nails found within the working area. Caution: Watch out for electric wires and ca ...

  • Makita DPC7321HD - page 11

    1 1 27 28 29 SERVICE Maintenance - Before performing maintenance work switch off the Power Cut (27) and pull out the plug cap. - Allow the Power Cut to cool off before doing any mainte- nance work (burn hazard)! - Always check the Power Cut before using it to make sure that it is in good working order . In particular , make sure that the cutting di ...

  • Makita DPC7321HD - page 12

    12 Denomination of components 1 Handle 2 Filter cover for air lter and spark plug cap 3 Cover lock 4 T ubular handle 5 Mufer 6 Protection hood 7 Grip 8 V -belt tension adjusting screw 9 Retaining nuts 10 Stand 1 1 Carburetor adjustment opening 12 Identication plate 13 Fuel tank with handle 14 Decompression valve 15 Starter grip 16 Air inta ...

  • Makita DPC7321HD - page 13

    13 5 5 7 7 9 8 Place the spring washer ( 8 ) on the arbour and insert the screw ( C/9 ) and tighten by hand. T urn the disc slowly until the stop hole of the V -belt pulley is visible in the cutting arm cover ( 10 ). Insert the Allen key ( 2 ) as far as it will go. The shaft is now blocked. T ighten the screw with the combination wrench ( 1 ) NOTE: ...

  • Makita DPC7321HD - page 14

    14 1.0 Us-gal. (3.7 l) 2.6 oz. (75 cm 3 ) 2.5 Us-gal. (9.4 l) 6.4 oz. (189 cm 3 ) 5.0 Us-gal. (18.9 l) 12.8 oz. (378 cm 3 ) 1 1 12 14 13 E F NOTE: The two fastening nuts ( 1 1 ) must be loosened before tightening the V -belt or checking the tension. T o increase the belt tension, turn the tightening screw ( 12 ) to the right (clockwise) wi ...

  • Makita DPC7321HD - page 15

    15 MAKIT A HP 100 high-performance two-stroke engine oil is available in the following sizes to suit your individual require- ments: 0,5 l order number 980 008 609 MAKIT A high-performance two-stroke engine oil (50:1) is available in the following sizes to suit your individual require- ments: 100 ml order number 980 008 606 1 l order number 980 008 ...

  • Makita DPC7321HD - page 16

    16 Starting the engine This model is tted with a semiautomatic decompression valve ( 1 ) to make starting easier . Depressing it reduces the force needed for compression, so little force is needed to accelerate the engine to its starting speed. The high pressure in the combustion chamber after the rst ignition automatically closes the decompr ...

  • Makita DPC7321HD - page 17

    17 H Stopping the engine Push the combination switch ( 1 ) down to position . STOP 10 Grasp the tubular handle rmly with one hand and press the Power Cut against the ground. Place the tip of your left foot in the rear handle. Pull the starter cable strong and rapidly until you hear the rst audible ignition. CAUTION: Do not pull out the starte ...

  • Makita DPC7321HD - page 18

    18 Adjusting the carburetor NOTE: The grinding parts are equipped with an electronic ignition to limit the speed. At the factory the idling speed has been set to approx. 2,500 1/min., but the running-in process of a new engine may require slight readjustment of the idling speed. A For correct adjustment of the idling speed the following steps must ...

  • Makita DPC7321HD - page 19

    19 8 9 10 2 1 3 4 7 6 5 A MAINTENANCE CAUTION: Before doing any work on the Power Cut turn off the engine, remove the cutting disc, pull the plug cap off the spark plug and wear protective gloves! CAUTION: Start the Power Cut only after complete assembly and inspection. B IMPORT ANT : Because many of the parts and assemblies not mentioned in this I ...

  • Makita DPC7321HD - page 20

    20 1 1 12 E Cleaning the protection hood Over time, the inside of the protective hood can become caked with material residue (especially from wet cutting), which if allowed to accumulate can hinder the free rotation of the cut- ting disc. For this reason the hood must be cleaned out from time to time. T ake off the cutting wheel with spring washer ...

  • Makita DPC7321HD - page 21

    21 Replacing the spark plug CAUTION : Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. Wear protective gloves! The spark plug must be replaced in case of damage to the insulator , electrode erosion (burn) or if the electrodes ar ...

  • Makita DPC7321HD - page 22

    22 22 23 19 21 20 STOP 9 10 1 1 Checking the ignition spark Insert the combination wrench ( 9 ) between the hood and cyl- inder only as shown. CAUTION! Do not insert the combination tool into the spark plug hole, but make contact only with the cylinder (otherwise you may damage the engine). Using insulated pliers, hold the spark plug ( 10 ) (unscre ...

  • Makita DPC7321HD - page 23

    23 A 24 25 26 R ep la c in g t he r e tu rn sp ri n g Re mov e t he sta rte r h ous in g ( see “R epl aci ng the st art er ca ble ”). T ake the air guide off the starter housing (see “Replacing the starter cable”). T ake off circlip ( 1 ) (circlip pliers, see “Accessories”). Remove the cable pulley ( 2 ). Unscrew screw ( 3 ). Evenly lev ...

  • Makita DPC7321HD - page 24

    24 3 4 5 6 7 Cutting attachment in central / side position NOTE: The Power Cut is delivered with the cutting attachment mounted in the middle position ( 1 ). For cutting up against ob- stacles, such as curbs or walls, the cutting attachment can be mounted to one side ( 2 ). Use this position only when actually necessary , and afterwards return the ...

  • Makita DPC7321HD - page 25

    25 15 17 16 Put the guard plate ( 15 ) on. Screw on nuts ( 16 ) and tighten by hand. T o tighten the V -belt see ”Tightening the V -belt / Checking V - belt tension”. T ighten the nuts ( 16 ) rmly with the combination wrench. Replace the grip ( 17 ) as shown. IMPORT ANT : When you reposition the cutting attachment, the direction of rotation ...

  • Makita DPC7321HD - page 26

    26 Diamond cutting discs (1) MAKIT A diamond cutting discs meet the highest demands in working safety , ease of operation, and economical cut- ting performance. They can be used for cutting all materials except metal . The high durability of the diamond grains ensures low wear and thereby a very long service life with almost no change in disc diame ...

  • Makita DPC7321HD - page 27

    27 General Entire Power Cut Clean exterior , check for damage. In case of damage, have repaired by a qualied service center immediately Cutting disc Inspect regularly for damage and wear . 7 Clutch Have inspected at a service center . Protection hood Clean, Check position (impact plate) 16 Before each start Cutting disc Inspect for damage and ma ...

  • Makita DPC7321HD - page 28

    28 T roubleshooting Malfunction System Observation Cause Cutting disc does not start turning Clutch Engine runs Damage to clutch Cutting disc runs in idle Carburetor , Cutting disc runs Incorrect idle speed, clutch blocked clutch Engine does not start or Ignition system Ignition spark Malfunction in fuel supply system, com- only with difculty pr ...

  • Makita DPC7321HD - page 29

    29 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service center . DPC731 1HD DPC7321HD 25 24 22 27 26 28 (4x) Accessories (not delivered with the Power Cut) Diamond cutting disc 14"/1.0" 22 966 244 020 1 Concrete Standard, dia. 350/25,4 mm 22 966 344 020 1 C ...

  • Makita DPC7321HD - page 30

    30 ...

  • Makita DPC7321HD - page 31

    31 ...

  • Makita DPC7321HD - page 32

    32 Specications subject to change without notice Form: 995 704 755 (1 1.07 GB) T o nd your local distributor , please visit www .makita-outdoor .com Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 ...

メーカー Makita カテゴリー Brush Cutter

Makita DPC7321HDのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DPC7321HDの取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita DPC7321HDの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita DPC7321HDの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita DPC7321HDの取り付け説明書、サービスマニュアル、簡易説明書、またはMakita DPC7321HDのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita DPC7321HDの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita DPC7321HDデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita DPC7321HDを使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita DPC7321HDユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita DPC7321HDの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita DPC7321HDの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita DPC7321HDに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita DPC7321HDデバイスの基本機能を使うにあたってのヒント。 Makita DPC7321HDのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita DPC7321HDに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita DPC7321HDのメーカー/サービスへの連絡先に関する情報。

Makita DPC7321HDについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita DPC7321HDの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita DPC7321HDで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)