-
Jet JML-1014 - page 1
OWNER’S MANUAL JML-1014 Mini Lathe JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 253-351-6000 A WMH Company Auburn, WA 98071-1349 Fax 800-274-6840 www.jettools.com e-mail jet@jettools.com M-708351 1-00 ...
-
Jet JML-1014 - page 2
Important Information 2-YEAR JET offers a two-year limited LIMITED WARRANTY warranty on this product REPLACEMENT PARTS Replacement parts for this tool are avail able directly form JET Equipment & Tools. To place an order, call 1-800-274-6848. Pleas e have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiratio ...
-
Jet JML-1014 - page 3
WARNING For your own safety, read this instruction manual before operating the lathe. Wear eye protection. Do not w ear gloves, necktie, or loose clothing. Tighten all locks before operating. Rotate the w orkpiece by hand before apply ing pow er. Rough out the w orkpiece before installing on the faceplate. Do not mount a split w orkpiece or one ...
-
Jet JML-1014 - page 4
• ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. • SECURE WORK. Use clamps or a vise to hold the work when it’s practical. It’s safer than using your hand and it frees both hands to operate the tool. • DON’T OVE ...
-
Jet JML-1014 - page 5
Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. Th is tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly insta ...
-
Jet JML-1014 - page 6
Specifications: JML-1014 Stock Nu mber ................................................................................................................... ..... 708351 Swing Over Bed (In.) ........................................................................................................... ........... 10 Swing Over Tool Re st Base (In.) ..... ...
-
Jet JML-1014 - page 7
Uncrating 1. Remove contents from the shipping box. 2. Inspect contents for shipping damage and report damage, if any, to your distributor. 3. Be sure to keep the box and packing material should you need to pack the lathe for moving. 4. Do not clean the lathe with anything other than a damp cloth or a mild solvent. Use of heavy solvents, paint thin ...
-
Jet JML-1014 - page 8
Nomenclature and Use Spur Center (A, Fig. 2) - locks into headstock and holds the workpiece during spindle turning. Face Plate (A, Fig. 3) - attaches to headstock and is used in face plate turning operations. Drift Rod (A, Fig. 4) - slides into the headstock to tap the spur center free. Stored in the hole in the base below the headstock. Tool Rest ...
-
Jet JML-1014 - page 9
Changing Spindle Speeds 1. Disconnect the machine from the power source (unplug). 2. Open the access doors at the left side of the base (A, Fig. 6), and at the back side of the headstock (A, Fig. 7). 3. Loosen the motor plate lock handle (A, Fig. 8). Lift up on the motor plate handle (B, Fig. 8) to take tension off the belt. 4. Move the belt (B, Fi ...
-
Jet JML-1014 - page 10
7. Insert the spindle into the spindle pulley aligning the key. 8. Thread the handwheel onto the spindle leaving a little space between the handwheel and headstock. Tighten set screws. 9. Center the spindle pulley and tighten set screw. 10. Wrap the belt around the motor pulley (lower). Be sure the belt is aligned with spindle pulley and motor pull ...
-
Jet JML-1014 - page 11
Parts List for the JML-1014 Mini Lathe Index Part No. No. Description Size Qty. 1 .......... JML-1 ................................. Headsto ck ........................................................ ............. .................... 1 ............ JML-1W ............................. Whit e Headsto ck ............................................ ...
-
Jet JML-1014 - page 12
40 ........ JML-40 ............................... Stud .................................................................. .......... ....................... 1 41 ........ JML-41 ............................... Tool Rest Body................................................. ................. ................ 1 ............ JML-41W ................. ...
Jet JML-1014についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもJet JML-1014の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJet JML-1014で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。