-
Porter-Cable QUICKSAND 335 - page 1
Double Insulated Random Orbit Sander MODEL 335 Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. __________________________ ...
-
Porter-Cable QUICKSAND 335 - page 2
2 IMPORT ANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause ...
-
Porter-Cable QUICKSAND 335 - page 3
3 9 . USE SAFETY GLASSES. Wear safety glasses or goggles while operating power tools. Also face or dust mask if operation creates dust. All persons in the area where power tools are being operated should also wear safety glasses and face or dust mask. 10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep co ...
-
Porter-Cable QUICKSAND 335 - page 4
4 5. KEEP HANDS AND BODY PARTS AWAY from rotating disc. Contact with rotating disc cause severe cuts and abrasions. 6. NEVER RUN SANDER with dust container or dust collector assembly removed. Dust could be blown into eyes. 7. WEAR EYE AND FACE PROTECTION. Injury to face and eyes can result if disc flies off or pad ruptures. Wear impact resistant gl ...
-
Porter-Cable QUICKSAND 335 - page 5
5 8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate detergent or trisodium (TSP) to wash and mop areas. 9. AT THE END OF EACH WORK SESSION put the paint chips and debris in a double ...
-
Porter-Cable QUICKSAND 335 - page 6
6 OPERA TING INSTRUCTIONS FOREWORD The Porter-Cable Random Orbit Sander provides rapid stock removal with 80 to 100 grit abrasive and swirl-free finishing with 120 to 150 grit abrasive. The Sander is equipped with a reversible pad that can accept 6" diameter, six hole (for six dust extraction) abrasives, with either STIKIT™ adhesive backed t ...
-
Porter-Cable QUICKSAND 335 - page 7
7 INST ALLING/REMOVING ABRASIVE DISC Hook & Loop Abrasive: The “hook” side of the sanding pad must be exposed for use with hook & loop abrasives (see REVERSIBLE PAD). 1. CAUTION: DISCONNECT MACHINE FROM POWER SOURCE. 2. Place machine on workbench with pad up (see Fig. 4). 3. Clean dust from pad face. 4. Position Hook & Loop Abrasive ...
-
Porter-Cable QUICKSAND 335 - page 8
Pressur e Sensitive Abrasive: The smooth side of the sanding pad must be exposed for use with pressure sensitive abrasives (see REVERSIBLE PAD). 1. CAUTION: DISCONNECT MACHINE FROM POWER SOURCE. 2. Place machine on workbench with pad up (see Fig. 5). 3. Clean dust from pad face. 4. Tear a new abrasive disc from roll and position disc to the sander ...
-
Porter-Cable QUICKSAND 335 - page 9
NOTE: A slight twisting action will ease removal and reassembly. Tap container lightly to remove compacted dust. DO NOT WASH CONTAINER. Dry compressed air may be used to blow out container. CAUTION: Wear safety glasses while using compressed air. The dust collector flange contains a clear plastic disc (C) Fig. 7, that acts as a check valve to preve ...
-
Porter-Cable QUICKSAND 335 - page 10
10 USING THE SANDER 1. CAUTION: Secure work to prevent if from moving during the sanding operation. Friction between the sanding disc and work will try to spin work away from sander and may cause bodily injury. 2. CAUTION: WEAR SAFETY GLASSES AND DUST MASK. 3. Place sander pad in light contact with the work before switching the motor “ON”. 4. G ...
-
Porter-Cable QUICKSAND 335 - page 11
11 SERVICE AND REP AIRS All quality tools eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE SERVICE STATION or PORTER-CABLE SERVICE CENTER. All repairs made by these agencies are fully guarantee ...
-
Porter-Cable QUICKSAND 335 - page 12
12 PRESSURE CATALOG NO. GRIT QUANTITY/PKG. SENSITIVE 72 660 06 25 60 25 ABRASIVES 72 660 08 50 80 50 72 660 10 10 100 10 72 660 10 50 100 50 72 660 12 50 120 50 72 660 15 10 150 10 72 660 15 50 150 50 72 660 22 10 220 10 72 660 22 50 220 50 HOOK & LOOP CATALOG NO. GRIT QUANTITY/PKG. ABRASIVES 73 660 06 05 60 5 73 660 06 25 60 25 73 660 08 25 80 ...
-
Porter-Cable QUICKSAND 335 - page 13
The following are trademarks of PORTER-CABLE • DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA Corporation): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® , QUICKS ...
Porter-Cable QUICKSAND 335についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもPorter-Cable QUICKSAND 335の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable QUICKSAND 335で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。