QSC Audio 522AAの取扱説明書

26ページ 1.54 mb
ダウンロード

ページに移動 of 26

Summary
  • QSC Audio 522AA - page 1

    TD-000164- 00 rev .A *TD-000164-00* RA VE 522aa 8x8 CobraNet Enabled Signal Processor Hardware Manual ...

  • QSC Audio 522AA - page 2

    2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol wit hin an equilateral tri angle is intended to al ert the user to the presence of uninsula ted “dangerous” voltage within the product’ s enclosure t hat may be of sufficien t magnitude to constit ute a risk of electri c shock to humans. The ...

  • QSC Audio 522AA - page 3

    3 Introduction 1- Power indicator 2- Diagnostic indicator 3- Network status indicators 4- Multi-function push buttons 5- Display 6- Rotary select/accept knob 7- Safe Mode push switch (recessed) 8- Analog outputs 9- Analog inputs 10- Relay outputs 11- Logic outputs 12- Omni inputs 13- RS-232 port 14- Network status indicators 15- QSControl 10BaseT r ...

  • QSC Audio 522AA - page 4

    4 Both software and firmware can be easily updated over the network. In the future, QSC will be adding new capabilities to both RA VE and QSControl.net. Our latest code releases and access to up-to-date information on RA VE and QSCon- trol.net are available at www .qscontrol.net. We invite you to visit us there. We've applied our many years ex ...

  • QSC Audio 522AA - page 5

    5 Introduction - Networking the RA VE 522aa The RA VE 522aa has two RJ-45 network connection ports on the r ear panel. One port is labeled "QSControl" and supports standard 10BASE-T Ethernet. The other port is labeled "CobraNet" and supports 100BASE-TX, also k nown as "Fas t Ethernet". In the followi ng sections, we de ...

  • QSC Audio 522AA - page 6

    6 Third, the RA VE 522aa and QSControl.net system are targeted at network switch deployments. The consumer costs of Ethernet switches have continued to fall over the last several years and are now comparable with repeaters on a per port basis. In addit ion, the sophistication and scalability of network switches make them i deal for new installation ...

  • QSC Audio 522AA - page 7

    7 Example #2 - CobraNet X-over mode: This is the simplest connection you can make between the RA VE 522aa and any of the other RAVE/BASI S models. Y ou use a CA T -5 crossover cable connected between the CobraNet ports of each unit. No network switch is required. This connection allo ws audio to pass between the two RA VE/BASIS units over CobraNet. ...

  • QSC Audio 522AA - page 8

    8 Example #3 - Singl e Wire Interface: Here all QSControl and CobraNet traffic shares the same single CA T -5 cable between the RA VE 522aa and an unmanaged Ethernet switch. The QSControl.net system manages traffic flow efficiently and reliably so that all audio and control data is delivered to its appropriate destination anywhere on the network. T ...

  • QSC Audio 522AA - page 9

    9 Example #4 - T wo-Wire Interf ace (shared network hardware): This example illustrates the T wo-Wire Interface with a managed Et hernet switch. The switch is configured with multiple virtual local area networks (VLANs). Ethernet deliveries can only reach des tination ports belonging to the same VLAN from which it was sourced. The figure shows a se ...

  • QSC Audio 522AA - page 10

    10 Example #5 - T wo-Wire Interf ace (separate netwo rk hardware): Example #5 is conceptually similar to example #4. The differenc e here is that separate networks are created by providing each l ocal area network (LAN) with its own network switch. Therefore, tra ffic segmentation is physical rather than logical. Ex ample #5 also pro- vides an addi ...

  • QSC Audio 522AA - page 11

    11 Unpacking There are no special unpacking precautions. However , it is recomm ended you keep the original packing material for reuse in the rare event that service be required. If service is required and the or iginal packing material is not available, ensure that the unit is adequately protected for shipment (strong box of appropriate size, suff ...

  • QSC Audio 522AA - page 12

    12 Computer Requirements & Software Installation Installing QSControl.net is easy . All you need to do is choose th e folder where the program is to be stored (the default settin g is accept- able for most applications). We recommend your syste m meet the following minimum requirements: 1- IBM PC compatible computer with a Pentium 4 processor . ...

  • QSC Audio 522AA - page 13

    13 General Information & Configuration Memories Amplifier Setup The QSC DataPort-equipped amplifiers connected to the RA VE 522aa must have their power switches in the “on” position. For initi al testing, use the lowest useful gain setting until the system is operating as expected. After the system setup has been verified and tested, gain s ...

  • QSC Audio 522AA - page 14

    14 Connections AC Power Cord Insert the molded receptacle of the AC power cord into the AC power inlet on the back of the RA VE 522aa. Plug the AC line connector into the AC outlet. The power supply will accept from 100 to 240 V olts AC, 47 to 440 Hertz, without any changes. If a different type of IEC power cord is required than the one supplied wi ...

  • QSC Audio 522AA - page 15

    15 Relay Out T wo sets of relay contacts are provided, RELA Y OUT 1 and RELA Y OUT 2. Contacts are floating and rated for 30VDC, 1A. There is one common terminal, one normally-closed contact terminal and one normally-open contact terminal. These are labeled as C, NC and NO on the rear panel. When the relay is not energized, the C terminal is connec ...

  • QSC Audio 522AA - page 16

    16 LED Indicators (continued) QSControl and Cobra Net Network St atus (Port) Indicators- There are three LEDs on the front and rear panels labeled RX, TX and LINK. One group is for the QSControl network port and the other for the CobraNet network port. Their functions are described below . Note: Port indicators on rear panel ar e color coded to mat ...

  • QSC Audio 522AA - page 17

    17 LCD Navigation Map (typical) Left side buttons h ave screen dependent function s. This read-o nly screen is the “out of the box” defa ult dis- play after power up. This is the most desired inf ormation when first sett ing up a net- work system. Once user moves to a di fferent scr een, the last screen acc essed becomes the new po wer up defau ...

  • QSC Audio 522AA - page 18

    18 Getting Started This section outlines one of the simpler methods of getting familiar with your RA VE and the QSControl.net software. The goal of this procedure is to get your computer and the RA VE connected and communicating and the QSControl.net software installed and running . After the software is installed and running, refer to the software ...

  • QSC Audio 522AA - page 19

    19 Getting Started (continued) 17- Select Device , Add New Device , from the menu. A new window will open prompting you to name the device. Name it logically , such as RA VE 1, or similar . Select the Device T ype and sele ct RA VE 522aa. At the Password prompt, enter “qsc” (lower case, no q uota- tion marks). This is the device password, separ ...

  • QSC Audio 522AA - page 20

    20 Operation QSControl Port The QSControl port operates on a 10BaseT Ethernet network. This por t is one of the primary means for connecting QSControl.net to the RA VE. The port may connect directly to a PC's 10BaseT or 10/100 ( auto-sensing or auto-negotiating) network interfac e card using a crossover cable. Data from the QSControl port may ...

  • QSC Audio 522AA - page 21

    21 Utility/Diagnostic Functions Safe Mode Switch Location of Safe Mode switch: The front panel has a small access hole on the left side, just left of the Power indicator . It is not labeled to help prevent accidental use. The Safe Mode switch can be operated by using a paperclip (or similar item) inserted in to the access hole and pushing. Safe Mod ...

  • QSC Audio 522AA - page 22

    22 Utility/Diagnostic Fu nctions (continued) RS-232 Communications Procedure: 1) Connect the RS-232 port of the RA VE 522aa to an unused serial port (COM port) of a PC using a normal (straight through) serial cable. 2) Open the HyperT erm inal program. This program is usually started by clicking the Windows Start icon, selecting Programs , then Acc ...

  • QSC Audio 522AA - page 23

    23 Utility/Diagnostic Fu nctions (continued) T elnet Access The RS-232 features can also be accessed via T elnet. The Micros oft T elnet application is a Windows program. Consult Windows documentation for T elnet information. Basic procedure for opening a T elnet session: 1 - T o open the T elnet session- Click ST ART , select RUN , type “T elnet ...

  • QSC Audio 522AA - page 24

    24 Preliminary Specification IN OUT THRU Dynamic Range (A ES-17, -60dB Method, all sensit ivities) unweighted >115dB >112dB >112dB A weighted >118dB >115dB >115dB Distortion (20Hz-20 KHz, all sen sitivities) +4dBu (max) <0.009% THD+N <0.009% THD+N <0.009% THD+N 2dB below clip (max) <0.009% THD+N <0.009% THD+N <0. ...

  • QSC Audio 522AA - page 25

    25 Preliminary Specification Relay Outputs 2 discrete floating relay switch outputs Connector T ype 3-pin "Phoenix Style" (a.k.a . "Euro Style") detachable terminal blocks Configuration Electromechanical Relay Pinout 1:NC 2:NO 3: COM Switching Capacity (nom) 1A 30VDC Logic Outputs 4 discrete outputs Connector T ype 2-pin "P ...

  • QSC Audio 522AA - page 26

    QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2004 “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T elephone Numbers: Main Number (714) 754-6 ...

メーカー QSC Audio カテゴリー Stereo System

QSC Audio 522AAのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 522AAの取扱説明書
- QSC Audioの製品カード
- パンフレット
- またはQSC Audio 522AAの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、QSC Audio 522AAの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、QSC Audio 522AAの取り付け説明書、サービスマニュアル、簡易説明書、またはQSC Audio 522AAのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、QSC Audio 522AAの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

QSC Audio 522AAデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQSC Audio 522AAを使用するのを助ける技術的文書のことです。説明書は通常、全てのQSC Audio 522AAユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

QSC Audioの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. QSC Audio 522AAの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQSC Audio 522AAの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。QSC Audio 522AAに関してこのドキュメントで見つけることができる全てのヒントの目次
3. QSC Audio 522AAデバイスの基本機能を使うにあたってのヒント。 QSC Audio 522AAのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。QSC Audio 522AAに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQSC Audio 522AAのメーカー/サービスへの連絡先に関する情報。

QSC Audio 522AAについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもQSC Audio 522AAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQSC Audio 522AAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)