-
Hobart HM1200 - page 1
FORM 34726 (Nov. 2001) MODEL HM1200 MICR O W A VE O VEN ML-126824 HM1200 MICROWAVE OVEN P O W E R L E V E L P ROG STAGE H I G H D EF ROST 1 2 1 2 3 4 5 6 X2 S T A R T S T O P / R E S E T 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com ...
-
Hobart HM1200 - page 2
– 2 – IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions must be followed, including the following: WARNING : TO REDUCE THE RISK OF BURNS, ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR EXPOSURE TO EXCESSIVE MICROWAVE ENERGY: 1. Do not use metal utensils in this oven. No aluminum foil or aluminum pie pans. No m ...
-
Hobart HM1200 - page 3
– 3 – PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY 1. Do not attempt to operate this oven with the door open since open-door operation can result in harmful exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks. 2. Do not place any object between the oven front face and the door ...
-
Hobart HM1200 - page 4
– 4 – Installation, Operation and Care of MODEL HM1200 MICR O W A VE OVEN SA VE THESE INSTRUCTIONS GENERAL Microwave heat is generated inside the food rather than being conducted through the food as in conventional methods. Time is used to control the amount of heating that occurs. Microwave energy is absorbed in proportion to the moisture cont ...
-
Hobart HM1200 - page 5
– 5 – LOCATION Place the oven on a suitable countertop, shelf or table with a smooth, flat and stable surface. Do not place the oven in a hot or damp area, near a gas or electric range. The microwave oven must not be located above or next to sources of excessive heat or greasy air. Clean air must be free to flow around the oven. There is a poss ...
-
Hobart HM1200 - page 6
– 6 – ELECTRICAL CONNECTION The cord and plug of this microwave oven must be connected to a separate circuit rated at 120 Volts, 60 Hertz, 20 Amps, Single Phase. No other appliance should share the circuit with this microwave oven. If it does, the branch circuit fuse may overload and cause either reduced heating or a blown fuse. GROUNDING INSTR ...
-
Hobart HM1200 - page 7
– 7 – OPERA TION Model HM1200 Microwave Oven DISPLAY AND KEYPAD Memory Keys are preset at the factory to HIGH power level and single stage cooking for these times: Refer to PROGRAMMING MEMORY (pages 9 – 10) to program Memory Keys to other times. Refer to PROG LOCK and PROG UNLOCK (page 12) to Lock or Unlock the programming function. The oven ...
-
Hobart HM1200 - page 8
– 8 – MANUAL HEATING When the oven is connected, a beep sounds. The display remains idle (blank) until you open the door and [ 0 ] displays for 1 minute. While [ 0 ] is displayed, the Memory keys or the Power Level key and Timer Dial allow the time and power level to be set for a cooking cycle. Manual Heating uses the Power Level key and Timer ...
-
Hobart HM1200 - page 9
– 9 – PROGRAMMING MEMORY KEYS 1 – 6 The oven must be set on Program Unlock to perform the functions on this page (refer to page 12). Programming Memory Keys for Single Portions 1. Keep the door closed. Make sure the Display is blank. Program Unlock must be active (not Program Lock). 2. While pressing the START key, press the POWER LEVEL key. ...
-
Hobart HM1200 - page 10
– 10 – Custom Programming the X2 Key for Multiple Portions The oven must be set on Program Unlock to perform functions on this page (refer to page 12). a. Keep the door closed. Make sure the Display is blank. b. While pressing the START key, press the POWER LEVEL key. [ PROG ] blinks in the Display. c . Press the Memory key you wish to program ...
-
Hobart HM1200 - page 11
– 11 – COOKING USING A PROGRAMMED MEMORY KEY AND THE X2 (DOUBLE PORTION) KEY This example shows how the oven runs after a Memory key has been programmed for 14 minutes at HIGH (refer to pages 8 – 9). This example requires that a large amount of food be placed in the oven. 1. Open the door; [ 0 ] displays. 2. Place the food in a suitable conta ...
-
Hobart HM1200 - page 12
– 12 – PROGRAM LOCK This procedure locks the Memory keys' power levels, stage(s) and time settings. The oven can be locked only if it is unlocked. If already locked, Program Lock cannot be done again. 1. Close the door. Make sure the Display is blank. 2. Press and hold in the X2 key for 10 seconds until [ PROG P L ] displays. 3. After 3 se ...
-
Hobart HM1200 - page 13
– 13 – PROGRAMMING BEEP TONE: LOUDNESS Beep Tone Loudness can have one of the following settings: 3 Loud, 2 Moderate, 1 Soft, 0 Silent. 1. Open the door and leave it open. 2. While pressing START, press POWER LEVEL. 3. The Display has the 1 above STAGE . Press Memory key 1 the number of times necessary to obtain the desired LOUDNESS. • Press ...
-
Hobart HM1200 - page 14
– 14 – DISPLAYING THE CYCLE COUNT The model HM1200 Microwave Oven incorporates a cycle counter which keeps track of the total number of cycles that the oven has operated. 1. Open the door and leave it open. 2. While pressing START, press Memory key 4 . 3. The Display shows the total number of cycles that the oven has run. For example: [ 99999 ] ...
-
Hobart HM1200 - page 15
– 15 – CLEANING WARNING : UNPLUG ELECTRICAL POWER CORD BEFORE PERFORMING ANY CLEANING OR MAINTENANCE. Keep the inside of the oven clean. If pieces of food or spilled liquids stick to the oven walls or between the door seal and door surface, they will absorb microwaves and may cause arcing or sparks. Wipe all spills with a damp cloth. A solution ...
-
Hobart HM1200 - page 16
– 16 – MAINTENANCE REPLACING THE CAVITY LIGHT BULB If the Cavity Light Bulb burns out, you can replace it yourself. WARNING : UNPLUG ELECTRICAL POWER CORD BEFORE PERFORMING ANY CLEANING OR MAINTENANCE. • Unscrew the screw on the Cavity Light Cover located on the left side of the cabinet (Fig. 7). • Replace the old bulb with a new 115 – 12 ...
Hobart HM1200についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHobart HM1200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart HM1200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。