Axor 06064XX0の取扱説明書

28ページ 5.84 mb
ダウンロード

ページに移動 of 28

Summary
  • Axor 06064XX0 - page 1

    C Cross 06066XX0 C Scroll 06065XX0 C Lever 06064XX0 Solaris² E 04147XX0 Allegro² E 04153XX0 Metro² E 04159XX0 Metris S 31317XX1 Focus S 31736XX1 T alis S 32317XX1 ThermoBalance II Rough & T rim Installation Instructions / W arranty ...

  • Axor 06064XX0 - page 2

    2 ThermoBalance II Rough 06623000 ThermoBalance II Rough with Stops 06627000 T echnical Specifications Recommended pressure 45 - 72 psi Maximum hot water temperature 165° F* Recommended hot water temp. 120° - 140° F* Nominal capacity @ 45 psi 8 gpm Nominal capacity @ 60 psi 11.5 gpm Safety stop 100° F Maximum output temperature 110° F** ½” ...

  • Axor 06064XX0 - page 3

    3 Installation Considerations For best results, this unit should be installed by a licensed, professional plumber . Large pressure differences between the hot and cold supplies should be balanced. Before beginning the installation, please read the instructions thoroughly . Inspect the product and make sure that all parts are present and in good con ...

  • Axor 06064XX0 - page 4

    4 Install the ThermoBalance II Rough Caution : T urn the water off at the supply before proceeding. Both outlets must be plumbed. Do not plug any port. Install the hot and cold supply lines to the rough. The hot supply must be connected to the hot inlet and the cold supply must be connected to the cold inlet. If the supplies are not connected to th ...

  • Axor 06064XX0 - page 5

    5 Flush the supply lines using the flushing plug When finishing the wall, install the wall material up to the oval installation box. Do not remove the installation box. When the trim is installed, the plaster shield portion of the installation box will be trimmed nearly flush to the wall and sealed to provide protection against water damage. The in ...

  • Axor 06064XX0 - page 6

    6 These trim kits are for use with Thermo- Balance II roughs 06623/06627 only . Do not use with any other rough. The finished wall must be complete and made watertight before installation of this trim kit. These instructions cover these models: V alve trim Shower set only trim C Lever 06064XX0 06082XX0 C Scroll 06065XX0 06083XX0 C Cross 06066XX0 06 ...

  • Axor 06064XX0 - page 7

    7 Cut the plaster shield so that it extends 1/16” outside the surface of the finished wall. Remove the label. Cut the support ar ms that connect the flushing plug to the installation box. Remove the flushing plug. Do not discard the screws. Insert the car tridge in the rough. Make sure that the locator tab on the cartridge goes straight into the ...

  • Axor 06064XX0 - page 8

    8 All other models: Install two Duotec strips directly on the carrier plate. Install the remaining two strips on the back of the escutcheon. T urn on the water supplies. Grasp the stop unit portion of the car tridge and turn it. If there is a leak around the cartridge, tur n the supplies off, and remove the cartridge. Confir m that the sealing gask ...

  • Axor 06064XX0 - page 9

    9 Install the carrier plate gasket and carrier plate with the carrier plate screws. Press the escutcheon ver y firmly over the carrier plate, so that the strips of Duotec interlock, produc- ing a ver y firm hold. Install the handle: T ighten the handle screw , using a 3 mm Allen wrench. For proper operation of the valve, the handle screw must engag ...

  • Axor 06064XX0 - page 10

    10 User Instructions The ThermoBalance II has two control features: the T emperature Selector and the Diver ter / V olume Control. The Diverter/V olume Control handle controls the water flow . The center position is “off”. T urn the handle counter-clockwise to send the water to outlet I (the bottom outlet). T urn it clockwise to send the water ...

  • Axor 06064XX0 - page 11

    11 Remove the clip and stop ring from the thermostatic car tridge stem. Put them in a safe place. T urn the ther mostatic mixer stem with your fingers, clockwise to make the water cooler , counter-clockwise to make the water warmer . T urn the stem until the water coming out is the desired maximum high temperature – 110° in most areas. Reinstall ...

  • Axor 06064XX0 - page 12

    12 Maintenance: Clean the filters While holding the stop unit still, use a second ad- justable wrench or a 17mm deep socket wrench to unscrew and remove the thermostatic car tridge. Rinse any debris from the filters on the thermostatic cartridge. Use a soft toothbrush, if necessar y . Do not attempt to remove the screens. Lubricate the o-rings with ...

  • Axor 06064XX0 - page 13

    13 Corps d'encastrement ThermoBalance II 06623000 Corps d'encastrement ThermoBalance II avec butées d’arrêt 06627000 La cartouche illustré ici est compris avec le jeu de garniture. A TTENTION : La robinetterie brute 06627000 La robinetterie brute 06627000 est munie de butées d’arrêt (arrêt d’isolation) intégrées à la valve. ...

  • Axor 06064XX0 - page 14

    14 À prendre en considération pour l’installation : Pour de meilleurs résultats, cette valve devrait être installée par un plombier professionnel certifié. Les différences importantes de pression d’arrivée d’eau chaude et d’eau froide doivent être équilibrées pour que la valve fonctionne correctement. V euillez lire attentivement ...

  • Axor 06064XX0 - page 15

    15 Installation : Attention : A vant de commencer , fermez l’eau à A vant de commencer , fermez l’eau à la valve principale. Raccordez les conduites d’alimentation de l’eau chaude et de l’eau froide à la pièce intérieure. La conduite d’alimentation de l’eau chaude doit être installée dans l’orifice d’arrivée prévu pour l? ...

  • Axor 06064XX0 - page 16

    16 Le i-box doit demeurer sur la valve. Rincez les conduites d’alimentation à l’aide du bouchon de rinçage. Le i-box comprend un bouchon de rinçage permet- tant de rincer la conduite et de tester la pression avant que la cartouche et la gar niture ne soient installées. Il est recommandé d’effectuer un test de pression de la tuyauterie av ...

  • Axor 06064XX0 - page 17

    17 Les instructions ci-après s’appliquent aux modèles suivants : Ensemble mitigeur Ensemble de pour la douche douche C Lever 06064XX0 06082XX0 C Scroll 06065XX0 06083XX0 C Cross 06066XX0 06084XX0 Solaris² E 04147XX0 04150XX0 Allegro² E 04153XX0 04156XX0 Metro² E 04159XX0 04162XX0 Metris S 31317XX1 31324XX1 Focus S 31736XX1 31772XX1 T alis S ...

  • Axor 06064XX0 - page 18

    18 Installation A vant de commencer , fermez l’eau à la vanne principale ou aux butées d’arrêt. Coupez la boîte d’installation (i-box) de façon à ce qu’elle dépasse de la surface du mur fini de 1/16 po. Retirez l’étiquette. Coupez les huit branches de support reliant le bouchon de rinçage à la i-box. Enlevez le bou- Enlevez le b ...

  • Axor 06064XX0 - page 19

    19 Ouvrez l’eau. T ourner T ourner le dispositif d’arrêt . Vérifiez Vérifiez l’étanchéité de tous les raccords. Si une fuite se produit entre la pièce intérieure et la cartouche, fer mez l’eau. Retirez la cartouche. Vérifiez que le joint du Vérifiez que le joint du Vérifiez que le joint du bouchon de rinçage a bien été enlevé ...

  • Axor 06064XX0 - page 20

    20 Réglez la poignée Outils requis : Thermomètre Clé hexagonale de 3 mm Ouvrez la valve. Placez le thermomètre dans le Placez le thermomètre dans le Placez le thermomètre dans le jet d’eau. T ournez le bouton de contrôle de la température jusqu’à ce que l’eau qui s’écoule atteigne 100°F . Fermez l’eau. À l’aide d’une clé ...

  • Axor 06064XX0 - page 21

    21 Instructions à l’intention de l’utilisateur Le ThermoBalance II est pour vu de deux fonctions de contrôle : le bouton de contrôle de la le bouton de contrôle de la le bouton de contrôle de la température et le levier de contrôle du débit / inverseur . Le levier débit / inverseur contrôle le débit de l’eau. La position centrale e ...

  • Axor 06064XX0 - page 22

    22 Entretien : Nettoyage des tamis de filtre Nettoyage des tamis de filtre Nettoyage des tamis de filtre Réglage de la butée limite d’eau chaude (en option) IMPORT ANT : Plusieurs municipalités appliquent des codes limitant la température de sortie Plusieurs municipalités appliquent des codes limitant la température de sortie Plusieurs muni ...

  • Axor 06064XX0 - page 23

    23 À l’aide d’une clé à molette, saisissez le pan de manoeu- vre sur le dispositif d’arrêt. T enez fermement le dispositif d’arrêt en place. À l’aide À l’aide À l’aide d’une seconde clé à molette ou d’une clé à douille longue de 17 mm, dévissez la cartouche ther mostatique et retirez-la. A TTENTION : Le dispositif d? ...

  • Axor 06064XX0 - page 24

    24 T roubleshooting Problem Possible Cause Solution W ater leaks between cartridge and rough sealing ring from flushing plug still inside rough remove sealing ring ceramic plate(s) inside cartridge damaged replace cartridge Handle turns, but water does not turn on/off handle screw not tightened tighten handle screw W ater drips for several minutes ...

  • Axor 06064XX0 - page 25

    25 1 cartridge 88586000 2 retainer plate 88519000 3 sleeve 88520XX0 4 carrier plate 88518000 5 Duotec spacers* 88529000 6 Duotec strips 96234000 7 carrier plate screw 88652000 8 cross handle 88608XX0 9 lever handle 88610XX0 10 scroll handle 88609XX0 11 Solaris² handle 88530XX0 12 Stratos handle 88547XX0 13 Metro handle 88548XX0 14 Interaktiv S/T a ...

  • Axor 06064XX0 - page 26

    26 Cleaning Recommendation for Hansgrohe Pr oducts Modern lavator y faucets, kitchen faucets, and showers consist of ver y different materials to comply with the needs of the market with regard to design and functionality . T o avoid damage and returns, it is necessar y to consider certain criteria when cleaning. Cleaning Materials for Faucets and ...

  • Axor 06064XX0 - page 27

    27 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...

  • Axor 06064XX0 - page 28

    Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No. 90965001-06 • Revised 04/2008 for installation or reinstallation of the product. D. Accessories, connected materials and products, or related products not manufactured ...

メーカー Axor カテゴリー Plumbing Product

Axor 06064XX0のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 06064XX0の取扱説明書
- Axorの製品カード
- パンフレット
- またはAxor 06064XX0の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Axor 06064XX0の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Axor 06064XX0の取り付け説明書、サービスマニュアル、簡易説明書、またはAxor 06064XX0のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Axor 06064XX0の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Axor 06064XX0デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAxor 06064XX0を使用するのを助ける技術的文書のことです。説明書は通常、全てのAxor 06064XX0ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Axorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Axor 06064XX0の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAxor 06064XX0の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Axor 06064XX0に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Axor 06064XX0デバイスの基本機能を使うにあたってのヒント。 Axor 06064XX0のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Axor 06064XX0に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAxor 06064XX0のメーカー/サービスへの連絡先に関する情報。

Axor 06064XX0についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAxor 06064XX0の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAxor 06064XX0で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)