Seagate KSD-541の取扱説明書

18ページ 1.58 mb
ダウンロード

ページに移動 of 18

Summary
  • Seagate KSD-541 - page 1

    -1- Industrial 5-Port Fa st Ethernet Switche s with SFP Slot a nd option al 4 PoE PSE Ports Ba sic Model: KSD-541 PoE Model: KSD-541-P In stallation Guide DOC.080104 ...

  • Seagate KSD-541 - page 2

    -2- (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from tim ...

  • Seagate KSD-541 - page 3

    -3- The information contained in this document is subject to change without prior notice. Copyright (C) . All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. W ARNING: This equi pment ha s been tested a nd found to comply with the li mits for a Cla ss A digital device, pursua nt to Part 15 of the FCC Rules. These limit ...

  • Seagate KSD-541 - page 4

    -4- T a ble of Contents 1. Introduction .................................................................................................. 5 1.1 Features .................................................................................................................. .6 1.2 Product Pa nels .......................................................... ...

  • Seagate KSD-541 - page 5

    -5- 1. Introduction The switches are 5-port Fa st Ethernet switches which are f eatured with four copper ports a nd one combo port. The combo port comes with one RJ-45 a nd one SFP slot. The SFP slot ca n be mounted with a fiber tra nsceiver optionally to support a fiber connection. For more coming PoE (Power Over Ethernet) a pplications, the PoE s ...

  • Seagate KSD-541 - page 6

    -6- 1.1 Fe ature s  Provides 5 10/100Mbps RJ-45 a nd one 100Mbps SFP slot  All copper ports support auto-negoti ation a nd auto-MDI/MDI-X detection  Provides full wire speed forwarding  Supports IEEE 802.3x flow control for full-duplex a nd ba ckpressure for half-duplex  Provides SFP slot for optional optical fiber connection  Pro ...

  • Seagate KSD-541 - page 7

    -7- 1.4 Specif ication s Copper Ports w/h PSE (P2-P5) Compli a nce IEEE 802.3 10Ba se-T , IEEE 802.3u 100Base-TX Connectors Shielded RJ-45 ja cks Pin a ssignments Auto MDI/MDI-X detection Configuration Auto-negoti ation T ra nsmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Network ca ble Cat.5 UTP Power over Ethernet IEEE 802.3af-comp ...

  • Seagate KSD-541 - page 8

    -8- Power over Ethernet Function (PoE Model) PSE Pin 4,5 Positive of power voltage (T ypical 48V DC) PSE Pin 7,8 Negative of power voltage (T ypical 48V DC) Discovery PD resista nce 15K ~ 33K PD Cla ssification Cla ss 0 ~ 4 Power delivery 15.4W max. (per port) Protection Under voltage protection Over voltage protection Over current detection DC IN ...

  • Seagate KSD-541 - page 9

    -9- 2. In stallation 2.1 Un pa cking The product pa ckage contains: • The switch unit • One product CD-ROM 2.2 Safety Cautions T o reduce the risk of bodily injury , electrical shock, fire, a nd da mage to the product, observe the following precautions. • Do not service any product except as explained in your system documentation. • Opening ...

  • Seagate KSD-541 - page 10

    -10- 2.4 Din-Rail Mounting The steps to mount the switch on a Din-rail are: One Din-rail mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit. Mount the device on a Din-rail. ...

  • Seagate KSD-541 - page 11

    -11- 2.5 Pa nel Mounting One pa nel mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit. The final di mension after pa nel bra cket is installed is shown below: 2.6 Applying Power The switch provides two types of power interfa ces, terminal block a nd DC power jack f or rece i ...

  • Seagate KSD-541 - page 12

    -12- Using T erminal Blocks Three terminal conta cts are provided: V dc Positive ( + ) termin al V dc Negative ( - ) termin al Cha ssis ground * Working V dc for general a pplication: +6V ~ +60V DC * Working V dc for PoE a pplication : +43V ~ +54V DC (T yp. 48V) One 3P terminal plugs are provided together with the switch. The plug is shown below: P ...

  • Seagate KSD-541 - page 13

    -13- 3. M a king Connection s 3.1 Ma king UTP Conne ction s The copper ports support the following connection type s a nd dista nce s: Network Cables 10BASE-T : 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm 100BASE-TX: 2-pair / 4-pair UTP Cat. 5, EIA/TIA-568B 100-ohm Link dista nce: Up to 100 meters Auto MDI/MDI-X Function This function allows the p ...

  • Seagate KSD-541 - page 14

    -14- 3.3 Ma king PoE Connection s This section describes how to make a connection between a PSE port a nd a PoE PD device. For the PoE switch model, Port 2, Port 3, Port 4 a nd Port 5 are equi pped with PoE PSE function. The ports are ena bled to deliver power together with network signal to a connected powered device vi a Cat.5 ca ble. T o make a ...

  • Seagate KSD-541 - page 15

    -15- 3.4 LED Indication L ED Function State Interpretation POWER Power status O N The power is supplied to the switch. OFF The power is not supplied to the switch. LIN K/ACT Por t l ink status O N A port link is e sta blished. (No traf fic) BLIN K Port link is up a nd there is traffic. OFF Port link is down. 100M/10M Port speed status O N Speed 100 ...

  • Seagate KSD-541 - page 16

    -16- 4. Application s 4.1 Application s with Ba sic Switch Model The following figure illustrates a ba sic switch model connects five computers vi a Cat.5 ca ble s. The following figure illustrates a ba sic switch model connects four computers vi a Cat.5 ca bles a nd uplink to a fiber ba ckbone network. ...

  • Seagate KSD-541 - page 17

    -17- 4.2 Applications with PoE Switch Model The figure below illustrates a PoE switch connects f our PoE IP camera s via Cat.5 ca ble s a nd uplinks to a fiber ba ckbone: The figure below illustrates a PoE switch connects f our PoE WLAN a ccess points vi a Cat.5 ca bles a nd uplinks to a ba ckbone: ...

  • Seagate KSD-541 - page 18

    -18- The figure below illustrates a PoE switch powered by a 48V DC power a da pter connects four PoE medi a converters vi a Cat.5 ca bles a nd uplinks to a fiber ba ckbone: ...

メーカー Seagate カテゴリー Switch

Seagate KSD-541のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- KSD-541の取扱説明書
- Seagateの製品カード
- パンフレット
- またはSeagate KSD-541の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Seagate KSD-541の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Seagate KSD-541の取り付け説明書、サービスマニュアル、簡易説明書、またはSeagate KSD-541のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Seagate KSD-541の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Seagate KSD-541デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSeagate KSD-541を使用するのを助ける技術的文書のことです。説明書は通常、全てのSeagate KSD-541ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Seagateの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Seagate KSD-541の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSeagate KSD-541の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Seagate KSD-541に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Seagate KSD-541デバイスの基本機能を使うにあたってのヒント。 Seagate KSD-541のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Seagate KSD-541に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSeagate KSD-541のメーカー/サービスへの連絡先に関する情報。

Seagate KSD-541についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSeagate KSD-541の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSeagate KSD-541で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)