RedMax G2500TSの取扱説明書

36ページ 0.39 mb
ダウンロード

ページに移動 of 36

Summary
  • RedMax G2500TS - page 1

    OWNER / OPERA T OR MANUAL CHAINSA WS T2040-93110(010)  The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING APPLICABLE SERIAL NUMB ...

  • RedMax G2500TS - page 2

    ...

  • RedMax G2500TS - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • RedMax G2500TS - page 4

    2. Specifications ■ G2500TS Power unit : Dis placement ····················································································· 1.6(25.4) cu-in(cm 3 ) Fuel ··············································· ...

  • RedMax G2500TS - page 5

    3. Symbols on the machine ❲ 5 ❳ Made in Japan RedMax IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS T O US EP A PH1 FOR SMALL OFF-RO AD ENGINES. ENGINE F AMIL Y : YKZXS.0254DE:EM ENGINE DISPLACEMENT : 25.4cc REFER TO O WNER'S MANUMAL FOR MAINTE- NANCE SPECIFICA TIONS AND ADJUSTMENTS. MANUF ACTURED : INFORMA TION IMPORT ANTE CONCERNANT ...

  • RedMax G2500TS - page 6

    ❲ 6 ❳ 4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel. ...

  • RedMax G2500TS - page 7

    ❲ 7 ❳ 4. For safe operation 1 6 . Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 1 7 . Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the gui ...

  • RedMax G2500TS - page 8

    A standard saw unit package contains the items as shown below. (SE1) (1) Power unit (2) Guide bar (3) Saw chain (4) Plug wrench Open the box and install the guide bar and the saw chain on the power unit as follows. The saw chain has very sharp edges. Use protective gloves for safety. 1. Pull the guard towards the front handle to check that the chai ...

  • RedMax G2500TS - page 9

    5. Installing guide bar and saw chain ❲ 9 ❳ SE5 SE6 6 . While holding up the tip of the bar,adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. (SE5) (1) Chain tension adjusting screw (a) Loosen (b) Tighten 7. Tighten the mounting nut securely with the bar tip held up (TORQUE: ...

  • RedMax G2500TS - page 10

    ❲ 10 ❳ 6. Fuel and chain oil ■ FUEL The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti- oxidant added quality oil expressly labeled for air- cooled 2-cycle engine use. RECOMMENDED MIXING RATIO GASOLINE 32 : OIL 1 Exhaust emission are controlled ...

  • RedMax G2500TS - page 11

    6. Fuel and Chain oil ■ CHAIN OIL Use motor oil SAE 10W-30 all year round, or SAE 30-40 in summer and SAE 20 in winter. Do not use waste or regenerated oil that can cause damage to the oil pump. NOTE ❲ 11 ❳ ...

  • RedMax G2500TS - page 12

    ❲ 12 ❳ ■ STARTING ENGINE 1 . Feed fuel and chain oil into their respective tanks and tighten the caps securely. (OP1) (1) Fuel (2) Chain oil 2 . Continuously push the priming bulb until fuel comes in the bulb. (OP2) 3. Put the switch to the "I" position. (OP3) (1) Switch 4 . Pull out the choke knob to the second-stage position. The ...

  • RedMax G2500TS - page 13

    OP8 7. Operation Once the choke knob has been pulled out, it will not return to the operating position even if you press down on it with your finger. When you wish to return the choke knob to the operating position, pull out the throttle lever instead. 5 . While holding the saw unit securely on the ground, pull the starter rope vigorousl y. (OP6) 6 ...

  • RedMax G2500TS - page 14

    ❲ 14 ❳ ■ ADJUSTING CARBURETOR (OP9) The carburetor on your unit has been factory adjusted, but may require fine tuning due to change in operating conditions. Before adjusting the carburetor, make sure that provided are clean air/fuel filters and fresh, properly mixed fuel. When adjusting, take the following steps: Be sure to adjust the carbur ...

  • RedMax G2500TS - page 15

    ❲ 15 ❳ 7. Operation OP10 OP11 • When the brake operates, release the throttle lever to slow down the engine speed. Continuous operation with the brake engaged will generate heat from the clutch and may cause trouble. • At machine inspection prior to each job, check the operating condition of the brake following the steps below. 1. Start the ...

  • RedMax G2500TS - page 16

    ❲ 16 ❳ 8. Sawing SA1 • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • Always follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vib ...

  • RedMax G2500TS - page 17

    SA3 ■ FELLING A TREE (SA2) When you fell a tree, be sure to warn your neighboring workers of the danger. 1. Decide the felling direction considering the wind, Iean of the tree, location of heavy branches, ease of job after felling, and other factors . 2. While clearing the area around the tree, arrange a good foothold and retreat path. 3. Make a ...

  • RedMax G2500TS - page 18

    ❲ 18 ❳ ● Cutting a pillowed log In the area A in the picture right above, saw up from the bottom one-third and finish by sawing down from the top. In the area B, saw down from the top one-third and finish by sawing up from the bottom. (SA4) ● Limbing a felled tree Be alert to the spring back of a cut limb. First check which way the limb is ...

  • RedMax G2500TS - page 19

    9. Maintenance Make sure the engine is stopped . ■ DAILY CHECK POINTS 1. Air filter Loosen the knob and remove the air cleaner cover. Take off the filter elements and tap off attached sawdust. When they are extremely dirty, shakewash with gasoline. Dry them completely before reinstalling. (MA1) 2. Oiling port Dismount the guide bar and check the ...

  • RedMax G2500TS - page 20

    ❲ 20 ❳ 9. Maintenance This saw is equipped with one of the following low kickback bar/chain combinations: RedMax Part Number Bar Size Guide Bar Saw Chain 12inch (30cm) G2512 91VG45X For replacement, use only above bar and chain, or the following; OREGON BAR 12 inch S/N DOUBLE GUARD BAR, Mount code #A041. (120 SDEA 041) GB BAR 12 inch MINI LAMIN ...

  • RedMax G2500TS - page 21

    When returning the filter, use a pinch not to be folded the suction pipe. 4. Spark plug Clean the electrodes with a wire brush and adjust the gap to 0.6mm. (MA8) Replacement plug: Champion RCJ-7Y After spark plug maintenance, reinstall the plug and plug cap firmly. (TORQUE: 14.7~17.6 N.m./150~180 kg-cm) Or it may cause the fire accident. (MA9) (1) ...

  • RedMax G2500TS - page 22

    ❲ 22 ❳ 9. Maintenance 7. Saw Chain It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. • The cut way does not go straight. • Vibration increases. • Fuel consumption increases. Cutter setting standar ...

  • RedMax G2500TS - page 23

    9. Maintenance Make sure every cutter has the same length and edge angles as illustrated. (MA14) (4) Cutter length (5) Filing angle (6) Side plate angle (7) Top plate cutting angle 8. Way of the cooling air • The engine metal parts can burn your skin. Never touch the cylinder, muffler or ignition plug etc. during operation or right after stopping ...

  • RedMax G2500TS - page 24

    ❲ 24 ❳ 9. Maintenance 9. Muffler (MA16) If you do not attach the muffler correctly, after engine starts, the muffler will be loosen and the hightemperature exhaust gas spout. After cleaning the muffler, pay attention to fit up the muffler according to the explanation as follows. 1 . Muffler body, muffler cover and baffle will be combined correc ...

  • RedMax G2500TS - page 25

    ❲ 25 ❳ 10. Storage 1. Empty the fuel tank and run the engine out of fuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of the reach of children. ...

  • RedMax G2500TS - page 26

    ❲ 26 ❳ 1 1. T roubleshooting Guide Case 1. Starting failure: Make sure the icing prevention system is not working. Case 2. Lack of power/Poor acceleration/Rough idling Case 3. Oil does not come out Check fuel for water or substandard mixture. Check for engine flooding. Check the spark. Check fuel for water or substandard mixture. Check air filt ...

  • RedMax G2500TS - page 27

    ❲ 27 ❳ 12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model ...

  • RedMax G2500TS - page 28

    ❲ 28 ❳ 12. Parts list Fig.1 POWER UNIT G2500TS (S/N 010101 and up) G2500TS ...

  • RedMax G2500TS - page 29

    ❲ 29 ❳ Fig.1 POWER UNIT (S/N 010101 and up) G2500TS 1 2841-12101 CYLINDER COMP 1 2 2841-12120 • ELBOW 1 3 2841-12210 PIPE 1 4 3310-82230 CLIP 1 5 3350-34320 ELBOW 1 6 2841-21110 CRANKCASE 1 7 01252-30520 BOLT, hexagon hole 4 M5x20 8 2841-41112 PISTON 1 9 2841-41210 RING, piston 1 10 1600-41310 PIN 1 11 1260-41320 RING, snap 2 12 1140-41330 BE ...

  • RedMax G2500TS - page 30

    ❲ 30 ❳ 12. Parts list Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 010101 and up) G2500TS ...

  • RedMax G2500TS - page 31

    ❲ 31 ❳ Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 010101 and up) G2500TS Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 T2040-81000 CARBURETOR ASS'Y 2 2630-81120 • PUMP COVER 1 3 3310-81130 • SCREW 1 4 3310-81280 • COVER 1 5 1480-81420 • PLUG 1 6 3350-81380 • SPRING 1 7 2630-81330 • SCREW 1 8 2880-81470 • SCREW ...

  • RedMax G2500TS - page 32

    THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS. KOMATSU ZENOAH Co ...

  • RedMax G2500TS - page 33

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL G2500TS UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED ...

  • RedMax G2500TS - page 34

    © Printed in Japan Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de ...

  • RedMax G2500TS - page 35

    ...

  • RedMax G2500TS - page 36

    KOMA TSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093  © Printed in Japan ...

メーカー RedMax カテゴリー Chainsaw

RedMax G2500TSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G2500TSの取扱説明書
- RedMaxの製品カード
- パンフレット
- またはRedMax G2500TSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、RedMax G2500TSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、RedMax G2500TSの取り付け説明書、サービスマニュアル、簡易説明書、またはRedMax G2500TSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、RedMax G2500TSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

RedMax G2500TSデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRedMax G2500TSを使用するのを助ける技術的文書のことです。説明書は通常、全てのRedMax G2500TSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

RedMaxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. RedMax G2500TSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRedMax G2500TSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。RedMax G2500TSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. RedMax G2500TSデバイスの基本機能を使うにあたってのヒント。 RedMax G2500TSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。RedMax G2500TSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRedMax G2500TSのメーカー/サービスへの連絡先に関する情報。

RedMax G2500TSについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRedMax G2500TSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRedMax G2500TSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)