Exmark XPの取扱説明書

24ページ 1.59 mb
ダウンロード

ページに移動 of 24

Summary
  • Exmark XP - page 1

    UL TRA V AC ® LAZER Z ® , LAZER Z ® AS, LAZER Z ® XP AND LAZER Z ® XS MODELS For Ultra V ac Serial Nos. 850,000 & Higher (to t Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999) (to t Lazer Z XS Units 352,000 & Higher) Part No. 4500-610 Rev . A ...

  • Exmark XP - page 2

    Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y . Exmark, or its distributors and dealers, accept no responsibility f or v ariations which may be evident in the actual specications of its products and the state ...

  • Exmark XP - page 3

    Introduction CONGRATULATIONS on the purchase of your Exmark Ultra V ac. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance, adjustment, and safety instr uctions for y our Exmark Ultra V ac BEFORE OPERATING Y OUR ...

  • Exmark XP - page 4

    Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 5 Safety Alert Symbol . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . ...

  • Exmark XP - page 5

    Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1. Safety alert symbol The safety alert symbol appears abov e infor ...

  • Exmark XP - page 6

    Safety collection system or mulch kit in place and w orking properly . DANGER There are rotating blades in the blo wer and under the mow er deck. Blade contact can cause serious operator or bystander injur y or ev en death. • Do Not reach into blo wer unless rotation indicator has stopped. Disengage PT O , stop engine, remo ve k ey , wait for all ...

  • Exmark XP - page 7

    Safety Figure 3 1. Safe Zone-Use the mower here on slopes less than 15 degrees 2. Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water . 3. Water • Remo v e or mark obstacles such as roc ks , tree limbs , etc. from the mowing area. T all g rass can hide obstacles . • W atc h for dit ...

  • Exmark XP - page 8

    Safety Safety and Instructional Decals • Keep all safety signs legible. R emov e all grease, dirt and debris from safety signs and instr uctional labels . • Replace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components . • If an ...

  • Exmark XP - page 9

    Safety 103-3508 LZUV52 Only 109-5890 UV60 and UV6672 9 ...

  • Exmark XP - page 10

    Specications Specications Model Numbers Serial Nos: 850,000 and Higher LZUV52–Fits Lazer Z (LZ) and Lazer Z AS (LAS) Units 789,999 and Lo wer with 52 inch dec k. UV60–Fits Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999 and Lazer Z XS Units 352,000 and Higher with 60 inch deck. UV6672–Lazer Z (LZ), Lazer Z AS (LAS ...

  • Exmark XP - page 11

    Specications Overall Length: w/Ultra V ac 52 inch Deck-Air -Cooled 105.70 inches (268.5 cm) 52 inch Dec k- Liquid-Cooled 106.00 inches (269.1 cm) 60 inc h Dec k-SN 599,999 and Low er Air -Cooled 106.65 inches (270.9 cm) 60 inch Dec k-SN 600,000–789,999 Air-Cooled 110.04 inches (279.5 cm) 60 inc h Dec k-SN 599,999 and Low er Liquid-Cooled 106.9 ...

  • Exmark XP - page 12

    Operation Product Overview Figure 4 1. Hood 4. Tube 2. Weight 5. Bag 3. Blower Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start Make sure you understand the controls , their locations , their functions , and their safety requirements . Ensure the blow er , belt cov er , bags , tube an ...

  • Exmark XP - page 13

    Operation hav e stopped before clearing blow er assembly or mow er dec k 3. T o remo v e the bags , rst shut off dec k dri ve , stop the engine and wait for all moving parts to stop . Open the hood and remov e the bags b y lifting up on the rear of the bag, then unhooking the front clip . Empty the bags b y inv erting them. 4. R einstall bags , ...

  • Exmark XP - page 14

    Operation Figure 6 Viewed from the right side 1. Hairpin 3. Discharge Chute 2. Chute Pivot Pin Note: Install chute with the tabs to the rear of the deck tabs as sho wn. W ARNING An unco v ered discharge opening will allow objects to be thrown in operator’s or bystander’s direction. Also, contact with blade could occur . Thrown objects or blade ...

  • Exmark XP - page 15

    Operation 6. Pull the spring loaded idler bac k and slip the belt ov er the top spindle deck sheav e . 7. Install the plastic belt cov er . On 60 inc h and 66 inch units the outside end of the cov er is slotted and can slip betw een the tw o washers on the belt shield stud. The plastic knob does not need to be remov ed. On 72 inc h and 52 inch unit ...

  • Exmark XP - page 16

    Operation T ransporting T ransporting a Unit Use a hea vy-duty trailer or truck to transport the machine . Loc k brak e and block wheels . Securely fasten the machine to the trailer or tr uck with straps , chains , cable , or ropes . Be sure that the trailer or tr uc k has all necessar y lighting and marking as required by law . Secure a trailer wi ...

  • Exmark XP - page 17

    Operation minimize the ramp angle . The trailer or truck should be as lev el as possible . Important: Do Not attempt to tur n the unit while on the ramp , y ou may lose control and driv e off the side. A v oid sudden acceleration when driving up a ramp and sudden deceleration when backing do wn a ramp . Both maneuv ers can cause the unit to tip bac ...

  • Exmark XP - page 18

    Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders. Remo ve the k ey from the ignition s witch, engage parki ...

  • Exmark XP - page 19

    Maintenance Lubricate Grease Fittings Note: See char t for ser vice inter v als. 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engage parking brake . 2. Lubricate ttings with NGLI g rade #2 multi-purpose gun grease. R efer to the following chart for tting locations and lubrication sc hedule. Lubrication Char t Fittin ...

  • Exmark XP - page 20

    Maintenance Cleaning Clean Mufer and Rear Frame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop , and remov e key . Engag e parking brak e. W ARNING Operating engine parts, especiall y the mufer, become extremely hot. Sev ere bur ns can occur on contact and de bris, such as leav es, grass, br ush ...

  • Exmark XP - page 21

    T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , Do Not o verlook the simple causes . F or example: starting problems could be caused b y an empty fuel tank. The follo wing table lists some of the common causes ...

  • Exmark XP - page 22

    Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair , replace or adjust any part on these products and found by us (in the ex ercise of our reasonable discretion) to be defective in factory ...

  • Exmark XP - page 23

    G01 1841 Figure 10 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees . Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. ...

  • Exmark XP - page 24

    MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM RIDE SEA T SUSPENSION SYSTEM FULL SUSPENSION SEA T DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT 12 V PO WER POR T MICRO-MULCH SYSTEM OPERA T OR CONTROLLE ...

メーカー Exmark カテゴリー Utility Vehicle

Exmark XPのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- XPの取扱説明書
- Exmarkの製品カード
- パンフレット
- またはExmark XPの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Exmark XPの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Exmark XPの取り付け説明書、サービスマニュアル、簡易説明書、またはExmark XPのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Exmark XPの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Exmark XPデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがExmark XPを使用するのを助ける技術的文書のことです。説明書は通常、全てのExmark XPユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Exmarkの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Exmark XPの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははExmark XPの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Exmark XPに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Exmark XPデバイスの基本機能を使うにあたってのヒント。 Exmark XPのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Exmark XPに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるExmark XPのメーカー/サービスへの連絡先に関する情報。

Exmark XPについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもExmark XPの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがExmark XPで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)