DeWalt DW705の取扱説明書

19ページ 1.01 mb
ダウンロード

ページに移動 of 19

Summary
  • DeWalt DW705 - page 1

    English ...

  • DeWalt DW705 - page 2

    D E WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 Printed in U.S.A. (FEB02-CD-1) Form No. 386782-01 DW705 Copyright 2001, 2002 ...

  • DeWalt DW705 - page 3

    DW705 (120 V olt)/DW705 (220 V olt) 12" Compound Miter Saw Scie à lnglets 300 mm (12 po) Sierra de àngulo compuesto 300 mm (12") INSTRUCTION MANUAL GUIDE D´UTILISA TION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. Before re ...

  • DeWalt DW705 - page 4

    English T able of Contents DOUBLE INSULATION/POLARIZED PLUG INSTRUCTIONS ....................................1 SAFETY INSTRUCTIONS FOR ALL TOOLS ......…………………………………………1 ADDITIONAL SAFETY RULES ........……………………………………………………….2 ELECTRICAL CONNECTION ........………………… ...

  • DeWalt DW705 - page 5

    English Important Safety Instructions WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS Double Insulation Double insulated tools are constructed throughout with two separate layers of electrical insulation ...

  • DeWalt DW705 - page 6

    English • DO NOT - Move either hand from saw or workpiece or raise arm until blade has stopped. • DO NOT - Use without Kerf Plate or when kerf slot is wider than 3/8". CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. WARNING: ...

  • DeWalt DW705 - page 7

    English 3 Electrical Connection Be sure your power supply agrees with the nameplate marking. 120 volts, AC/DC means that your saw will operate on alternating or direct current. A voltage decrease of 10 percent or more will cause a loss of power and overheating. All D E WALT tools are factory tested. If this tool does not operate, check the power su ...

  • DeWalt DW705 - page 8

    English FIG. 3 45 55 40 3 5 5 0 4 5 FIG. 4 LOCK DOWN PIN Accessories Recommended accessories for use with your tool are available at extra cost from your local service center. CAUTION: The use of any non-recommended accessory such as dado sets, molding cutters, or abrasive wheels may be hazardous. If you need assistance in locating any accessory, p ...

  • DeWalt DW705 - page 9

    5 English ALWA YSADJUST FENCE PROP ERLYBEFOR EUSE DW7050 DW7051 SELF-TAPPING STUD LOCKNUTS END PLATE CLAMPING BRACKET STOP WASHER AND SCREW KNOBS BOTTOM HOLE (USE IF ON RIGHT SIDE) BRACKET TOP HOLE (USE IF ON LEFT SIDE) As shown in Figure 6 the inner clamp washer is installed first, then the blade adapter. The blade adapter is designed ...

  • DeWalt DW705 - page 10

    6 English Stop as shown in Figure 12, and adjust the stop screw as necessary. Hold the stop screw in place and tighten the lock nut. BEVEL POINTER If the bevel pointer does not indicate zero, loosen the screw that holds it in place and move the pointer as necessary. SUGGESTION: The bevel pointer is quite thick and for accuracy’s sake set the top ...

  • DeWalt DW705 - page 11

    7 English 45 45 40 50 3 5 55 30 6 0 25 65 2 0 7 0 1 5 7 5 45 45 40 50 35 55 30 6 0 0 5 15 20 25 30 35 10 15 20 25 30 35 22.5 31.62 22.5 31.62 75 70 65 60 55 75 70 65 60 55 85 9 0 80 1 1 2 1 1 2 FIG. 9 MITER CLAMP KNOB FIG. 10 MITER SCALE POINTER FIG. 8 MITER SCALE ADJUSTMENT SCREW (three of these) MITER LATCH The front section of the guard is louve ...

  • DeWalt DW705 - page 12

    8 English FIG. 11B STOP SCREW LOCK NUT FIG. 12 BEVEL POINTER SCREW BEVEL STOP FIG. 11A BEVEL HOUSING one that best fits your needs. (Page 3) BODY AND HAND POSITION (SEE FIG. 16) Proper positioning of your body and hands when operating the miter saw will make cutting easier, more accurate and safer. Never place hands near cutting area. Place hands n ...

  • DeWalt DW705 - page 13

    9 English ALWAYSADJUSTFENCE PROPERLYBEFOREUSE D ANGE R K EE P A WA Y F R OM BL AD E FIG. 14 FIG. 15 TRIGGER SWITCH GUIDE GROOVE HOLE FOR PADLOCK LEFT SIDE FENCE CLAMPING KNOBS FIG. 13 LEFT SIDE BEVEL STOP SCREW with it. Example: To make a 4 sided box with 26° exterior angles (Angle A, Figure 19), use the upper right arc. Find 26° on t ...

  • DeWalt DW705 - page 14

    10 English ALWAYSA DJUSTFENCE PROPERLYBEFOREUS E D A N GER K EE P AW A Y F RO M BL ADE D A N G E R K E E P A W A Y F R O M B L A D E IMPROPER CUT IMPROPER CUT PROPER CUT 2. Save left side of cut Right side 1. Miter Right 45° 2. Save right side of cut OUTSIDE CORNER: Left side 1. Miter right at 45° 2. Save left side of cut Right side 1 ...

  • DeWalt DW705 - page 15

    11 English FIG. 17 FIG. 18 FIG. 19 A. B. ANGLE “A” 0 5 15 20 25 30 35 10 15 20 25 30 22.5 31.62 22.5 31.62 75 70 65 60 55 75 70 65 60 85 9 0 80 1 1 2 1 1 2 FIG. 20 MITER SCALE FIG. 21 V1 V2 MITER ARM CENTER MARK ON VERNIER SCALE ALIGNS WITH DESIRED WHOLE ANGLE ON MITER SCALE (24° RIGHT MITER) 1/4° VERNIER MARK ALIGNS WITH CLOSET WHOLE DEGREE ...

  • DeWalt DW705 - page 16

    12 English FIG. 23 FIG. 24 accurately set on your saw.) Since most rooms do not have angles of precisely 90 degrees, you will have to fine tune your settings anyway. PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT! INSTRUCTIONS FOR CUTTING CROWN MOLDING LAYING FLAT AND USING THE COMPOUND FEATURES 1. Molding laying with broad back surface down ...

  • DeWalt DW705 - page 17

    13 English This way, when corners other than 90 degrees are encountered, the saw can be quickly and easily adjusted for them. Use the crown molding fence accessory to maintain the angle at which the molding will be on the wall. INSTRUCTIONS FOR CUTTING CROWN MOLDING ANGLED BETWEEN THE FENCE AND BASE OF THE SAW FOR ALL CUTS: 1. Angle the molding so ...

  • DeWalt DW705 - page 18

    14 English Important To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. Full W arranty D E WALT heavy duty industrial tools are warranted for on ...

  • DeWalt DW705 - page 19

    15 English Tr ouble Shooting Guide BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS TROUBLE! SAW WILL NOT START WHAT’S WRONG? WHAT TO DO… 1. Saw not plugged in 1. Plug in saw. 2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker 3. Cord damaged 3. Have cord replaced by authorized service center 4. Brushes worn out 4 ...

メーカー DeWalt カテゴリー Cordless Saw

DeWalt DW705のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DW705の取扱説明書
- DeWaltの製品カード
- パンフレット
- またはDeWalt DW705の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、DeWalt DW705の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、DeWalt DW705の取り付け説明書、サービスマニュアル、簡易説明書、またはDeWalt DW705のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、DeWalt DW705の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

DeWalt DW705デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDeWalt DW705を使用するのを助ける技術的文書のことです。説明書は通常、全てのDeWalt DW705ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

DeWaltの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. DeWalt DW705の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDeWalt DW705の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。DeWalt DW705に関してこのドキュメントで見つけることができる全てのヒントの目次
3. DeWalt DW705デバイスの基本機能を使うにあたってのヒント。 DeWalt DW705のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。DeWalt DW705に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDeWalt DW705のメーカー/サービスへの連絡先に関する情報。

DeWalt DW705についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDeWalt DW705の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDeWalt DW705で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)