Makita 51778の取扱説明書

16ページ 0.9 mb
ダウンロード

ページに移動 of 16

Summary
  • Makita 51778 - page 1

    7-iw Hypoid Saw Blade diameter 185 mm 17-1/4"1 185 mm (7-1/4") MODEL 51 778 MODEL 5277B No load speed Overall Net Max. cutting capacities 50 O 450 (RPMI length weight 439 mm 6.8 kg 4,300 (17-1/4"1 (15.0 Ibs) 62 mm 40 mm 44 mm (2-3/8") (1-9/16") (1-23/32") INSTRUCTION MANUAL DOUBLE INSU LATlO N ...

  • Makita 51778 - page 2

    GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not ...

  • Makita 51778 - page 3

    11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. ...

  • Makita 51778 - page 4

    Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards. ...

  • Makita 51778 - page 5

    11. Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back towa ...

  • Makita 51778 - page 6

    Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Use extra caution when making a &qu ...

  • Makita 51778 - page 7

    15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down. DON'T TRY TO HOLD SHORT PIECE ...

  • Makita 51778 - page 8

    SYMBOLS Described below are symbols commonly listed on tools. v ................................. volts A ................................. amperes Hz ................................. herts kg ................................. kilograms h ................................. hours min ................................. minutes S ...................... ...

  • Makita 51778 - page 9

    OPERATION Removing or installing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt clock- wise. Then remove the hex bolt, outer flange and blade. Shaft lock 2 Fig. ...

  • Makita 51778 - page 10

    Adjusting depth of cut I Fig. 12 Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. Fig. 11 CAUTION: 0 Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts. 0 After adjusting the depth of cut, always tighten the lever securely. Bevel cutti ...

  • Makita 51778 - page 11

    Switch action 1 To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates pro- perly and returns to the "OFF" position when released. Cutting operation Grasp the rear handle with your right hand, the front grip with your left. Set th ...

  • Makita 51778 - page 12

    MA1 NT ENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be ...

  • Makita 51778 - page 13

    ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Guide rule Part No. 1651 53-3 A-90037 Wrench ...

  • Makita 51778 - page 14

    Sep.-07-'95 US 185 mm (7-1/4") HYPOID SAW Model 5177B/5277B Note: The switch and other part configurations may differ from country to country. 14 ...

  • Makita 51778 - page 15

    MODEL 51778152770 Sep.-07-'95 US 10 11 12 13 14 15 16 17 $& DESCRIPTION 11 21 31 41 51 61 71 81 91 3 1 1 1 1 1 1 1 ,&, DESCRIPTION 48 49 50 51 52 53 54 55 56 51 58 59 1 1 1 2 1 1 1 1 1 1 1 1 18 15 20 21 22 24 25 26 27 28 25 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 62 1 63 1 164 1 1 1 1 1 1 1 1 1 2 3 1 Hex Flange Head Bolt ...

  • Makita 51778 - page 16

    MAKITA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from workanshl and materials for the period of ONE YEAR from the date of original urchaae. Should any troubi develop during this one-year period, return the COMPLETE tool, fr&t prep ...

メーカー Makita カテゴリー Saw

Makita 51778のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 51778の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita 51778の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita 51778の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita 51778の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita 51778のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita 51778の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita 51778デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita 51778を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita 51778ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita 51778の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita 51778の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita 51778に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita 51778デバイスの基本機能を使うにあたってのヒント。 Makita 51778のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita 51778に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita 51778のメーカー/サービスへの連絡先に関する情報。

Makita 51778についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita 51778の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita 51778で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)