-
Metabo Invert 130/40 - page 1
115 162 4029 / 0803 - 3.2 Bedienungsanleitung Operating Instructions Instructions de service Gebruiksaanwijzing Instrucciones de uso Invert 130/40 Invert 130/60 Achtung! Lesen Sie diese Anleitung vor der Installation und Inbetriebnahme aufmerksam durch. Attention! Carefully read through these instructions prior to installation and commissioning. At ...
-
Metabo Invert 130/40 - page 2
ENG Table of Contents 1 Technical Specifications 2 Scope of Application 2.1 Information 3 Commissioning 4 Description 5 Operation 6 TIG-Welding (optional) 6.1 Tips for TIG-Welding 7 Overloads 8 Trouble Shooting 9 Safety Information 9.1 Protection against Electrical Accidents 10 Wiring Diagram Invert 130/40 Invert 130/60 Mains voltage: 1 ~ 230/240 V ...
-
Metabo Invert 130/40 - page 3
2.1 Information - Shown On Type Plate The following explanations refer to the numbered boxes shown in Figure 2.3 according to ISO/IEC 60974-1. a) Identification Box l Name and address of the manufacturer or distributor or importer and, optionally, a trade mark and the country of origin, if required Box 2 Type (identification) as given by the manufa ...
-
Metabo Invert 130/40 - page 4
b) Welding Output Box 6 Welding process Symbol e.g.: Manual metal arc welding with covered electrodes Tungsten inert-gas welding Metal inert and active gas welding including the use of flux cored wire Selfshielded flux cored arc welding Submerged arc welding Symbol for plasma cutting Symbol for plasma gouging Box 7 Symbol for welding power sources ...
-
Metabo Invert 130/40 - page 5
Column a) need not be used if the duty cycle (duty factor) for the rated maximum welding current is 60 % or 100 %. Column b) need not be used if the duty cycle (duty factor) at the rated maximum welding current is 100 %. c) Energy input Box 14 Energy input symbol e.g.: Input supply, number of phases (e.g. l or 3), symbol for alternating current and ...
-
Metabo Invert 130/40 - page 6
5 Operation The welding machines Invert 130/40 and 130/60 are primary clocked inverters, suitable for manual arc welding with coated stick electrodes and for direct current TIG welding (optional). The electrode diameter and the required welding current are selected according to the material to be welded. 3 Commissioning Caution: This product is ass ...
-
Metabo Invert 130/40 - page 7
Dust, dirt and metal chips will harm any welding machine. It is of particular importance that the air ventilation for cooling is not disabled. Prior to welding the joints must be cleaned and dirt, rust, grease and paint removed. Also slag from previous welds must be completely removed. Attach earth clamp firmly to work piece, assuring good metal to ...
-
Metabo Invert 130/40 - page 8
The correct arc length is important for a good weld, because with too short or too long an arc both welding current and working voltage change. A low working voltage causes insufficient penetration. Too high or too low welding current gives a poor welding seam. Too long an arc does not sufficiently melt the parent material, resulting in high spatte ...
-
Metabo Invert 130/40 - page 9
6 TIG Welding (optional) Due to the same welding characteristics as with manual arc welding, TIG welding is possible with models Invert 130/40 and 130/60. For TIG welding a TIG torch model SR 17 V (see section 11) is used, which is always connected to the negative (-) pole. The arc is started by scratching with the tungsten electrode on the workpie ...
-
Metabo Invert 130/40 - page 10
9 Safety Precautions/Accident Prevention - This Welding Machine should only be used for its intended application (TIG and manual arc welding). - Operate machine only on power supply circuits having a fully operational protective bonding circuit (earth/ground lead). - Know and adhere to all applicable local safety standards and codes. 9.1 Protection ...
-
Metabo Invert 130/40 - page 11
10 Wiring Diagram Invert 130/40 and 130/60 (2) (5) (6) (1) (7) (3) (1) Power cable (2) Switch/plug (3) Control PCB (4) Transformer (5) Diodes (6) Choke (7) Fan (4) 11 Exploded View Drawing and Spare Parts List TIG-Torch SR 17 V 1 2 3 4 6 7 9 12 15 14 16 5 8 10 11 13 (5) Ø 8,0 (6) Ø 9,5 Ø 1,0 Ø 1,6 Ø 1,0 Ø 1,6 1 132 712 7230 2 132 712 7248 3 1 ...
-
Metabo Invert 130/40 - page 12
D DEUTSCH ENG ENGLISH KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY Wir erklären in alleiniger Verantwortlichkeit, dass dieses Produkt mit den folgenden Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien**. We herewith declare in our sole responsibility that this product complies with the following standards* in accordance with th ...
-
Metabo Invert 130/40 - page 13
Country; Company; Address 1; Address 2; City; Phone; Fax; E-mail Albania; Extra Industrial Goods; Rl. Fadil Rada 88; ; Tirana; (+35 5) 42 - 3 30 62; (+355) 42 - 3 30 62; abeqiri@t-onli ne.de Algerie; Haddad Equipement Pro fessionel; 98 A, Site du Lycée ; ; 16012 Rouiba; (+213) 21 - 85 49 05; (+213) 21 - 85 57 72; heprouiba@hotmail.c om Argentina; ...
Metabo Invert 130/40についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもMetabo Invert 130/40の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMetabo Invert 130/40で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。