-
Alpine SPX-177A - page 1
SPX-177A / SPX-137A Component 2-way Speaker System OWNER’S MANUAL Please read before using this equipment MANUEL DE L'UTILISA TEUR V euillez lire le présent manuel avant la mise en service du matériel. ALPINE ELECTRONICS, INC. T okyo office ; 1-1-8 Nishi Gotanda, Shinagawa-ku, T okyo 141-8501, Japan T el.: (03) 3494-1 101 ALPINE ELECTRONIC ...
-
Alpine SPX-177A - page 2
2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LES INST ALLER CORRECTEMENT . L’utilisation d’autres pièces non désignées risque de provoquer des dommages à l’intérieur de l’appareil ou son installa- tion risque de ne pas être faite correctement, et les pièces desserrées peuvent provoquer des dangers. NE P AS INST ALLER DANS DES E ...
-
Alpine SPX-177A - page 3
3 19. Fixed-flush mount cup / Embase fixe à niveau …………………… x2 20. Mounting clip / Attache de montage .....…………………………. x4 21. Swivel-spacer / Swivel-spacer .....………… ………………. x4 22. Screw st4.2x9.5mm / Vis st4.2x9.5mm....…………………….. x2 23. Screw st4.2x19mm / Vis st4.2x19mm…... ...
-
Alpine SPX-177A - page 4
4 T abel of Contents Installation W oofer (SPX-177A)..................................................................... 5 W oofer (SPX-137A)..................................................................... 7 T weeter ........................................................................................ 8 Crossover Network................... ...
-
Alpine SPX-177A - page 5
5 Installation (SPX-177A) W oofer: Surface mount W oofer: Factory/stealth Notes: l Attach gasket tape as shown. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm Notes: l Attach gasket tape as shown. st4.2x25mm Installation (SPX-177A) W oofer : Montage en surface W oofer : Usine / montage ...
-
Alpine SPX-177A - page 6
6 Installation (SPX-177A) W oofer: Factory/OEM custom fit Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs. Hardware: l Use st4.2x25mm for adapter to vehicle l Use M4x10mm for speaker to adapter (adapter only) l Use M4x18mm for speaker to adapter (adapter + spacer) l Use M4x20mm fo ...
-
Alpine SPX-177A - page 7
7 Installation (SPX-137A) W oofer: Surface mount Notes: l Attach gasket tape as shown, then lock speaker into grille ring. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm W oofer: Factory/stealth Notes: l Attach gasket tape as shown. st4.2x25mm W oofer: Factory/Size-up/OEM custom fit Not ...
-
Alpine SPX-177A - page 8
8 Installation T weeter: Swivel-surface mount st4.2x19mm Fig. 1 Fig. 2 Fig. 3 Notes: l Before mounting, insert swivel retention cup into housing. Then rotate until achieving a positive lock using an appropriate tool (screwdriver , etc.). l Mount complete swivel-surface cup and fix swivel spacer to base. (Fig. 1) l Lock swivel ring to tweeter housin ...
-
Alpine SPX-177A - page 9
9 Installation T weeter: Swivel-flush mount Fig. 1 Fig. 2 Fig. 3 Notes: l Before mounting, insert swivel retention cup into housing. Then rotate until achieving a positive lock using an appropriate tool (screwdriver , etc.). l Insert complete swivel-flush cup with mounting clips first through opening. (Fig. 1) l Press mounting clips at center and s ...
-
Alpine SPX-177A - page 10
10 Installation T weeter: Fixed-flush mount Fig. 1 Fig. 2 Fig. 3 Notes: l Insert fixed-flush cup with mounting clips first through opening. (Fig. 1) l Press mounting clips at center and secure with screw . (Fig. 2) l Make connections, then insert and lock tweeter into cup. (fig. 3) st4.2x9.5mm Caution: l If custom painting is desired, remove grille ...
-
Alpine SPX-177A - page 11
11 Installation T weeter: Surface-angle mount Notes: l Remove network cover , and mount as shown l Connect wires to terminal blocks accordingly . (see System Connection Diagrams section) l Make appropriate jumper settings using jumper puller tool (see Crossover Network Settings section) l Re-secure network cover . Crossover Network st4.2x19mm Notes ...
-
Alpine SPX-177A - page 12
12 System Connections Single Input Bi-wire Input Note: Signal link jumpers highlighted in black must be inserted for proper function of single input configuration. Wiring for connection of crossover network to amplifier is not included. Caution: These jumpers must be removed when using b-wire input. Connexions du système Entrée simple Entrée par ...
-
Alpine SPX-177A - page 13
13 Crossover Network Settings It is common knowledge that the automotive environment poses numerous acoustic challenges to achieving high-fidelity sound. Fortunately , many of these problems can be overcome with proper speaker placement, equalization, digital time correction, or other techniques. However, the transition between drivers in a speaker ...
-
Alpine SPX-177A - page 14
14 Crossover Network Settings System T ype 1 (default) Speaker Placement Description: In this system type, woofer and tweeter are mounted in close proximity to each other , and are mounted in essentially the same plane. Due to positioning limitations in some applications, additional tuning may be required using the axis jumpers for both the woofer ...
-
Alpine SPX-177A - page 15
15 Crossover Network Settings System T ype 1 Filter Description: In this setting, the woof er and tweeter are at appro ximately equal distance from the listener . Using the kic k-panel for placement is only one of man y locations av ailable to mount both drivers together . What is impor tant is that but b y put- ting these tw o dr i vers in close p ...
-
Alpine SPX-177A - page 16
16 Crossover Network Settings System T ype 2 Speaker Placement Description: In this system type, woofer and tweeter are mounted different locations and at dif ferent distances from the listener . Also of significance, is the fact that the tweeter is the nearest driver . All component locations listed below are commonly available in most vehicles, b ...
-
Alpine SPX-177A - page 17
17 Crossover Network Settings System T ype 2 Filter Description: In this system type, the woofer is in a dif ferent plane from the tweeter , making it necessary to use the phase correction sections of the network to compensate for the different relative positions. With this particular network set- ting, user adjustment of the woofer axis jumpers is ...
-
Alpine SPX-177A - page 18
18 ...
-
Alpine SPX-177A - page 19
19 Specifications Specifications System SPX-177A SPX-137A T ype Component 2-wa y speak er Component 2-w ay speak er P ower Handling (peak/RMS) 240/60 W 200/50 W Impedance 4 W 4 W F requency Response 35-35 kHz 35-35 kHz Net W eight 5 kg 4.5 kg Drivers General Speaker siz e 6.5” (SPX-177A) 5.25” (SPX-137A) 26 mm Speaker T ype Bass/Midrange Bass/M ...
-
Alpine SPX-177A - page 20
Designed by Alpine Electronics of America, Inc. Printed in Denmark by T eam L ynderup ...
Alpine SPX-177Aについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもAlpine SPX-177Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAlpine SPX-177Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。