Bunn CWTF APS-DVの取扱説明書

31ページ 2.08 mb
ダウンロード

ページに移動 of 31

Summary
  • Bunn CWTF APS-DV - page 1

    CWT -DV , CWT APS-DV , CWTF-DV , CWTF APS-DV ...

  • Bunn CWTF APS-DV - page 2

    Page 2 INTRODUCTION This equipment will brew a half-gallon batch of coffee into an awaiting dispenser. It can be easily configured for 120V 15 amp, 120/208V 20 amp or 120/240V 20 amp. The brewer has a hot water faucet for allied beverage use. It is only for indoor use on a sturdy counter or shelf. BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Mat ...

  • Bunn CWTF APS-DV - page 3

    Page 3 #12364.0000 ...

  • Bunn CWTF APS-DV - page 4

    Page 4 #00656.0000 ...

  • Bunn CWTF APS-DV - page 5

    Page 5 36102 090203 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. Requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. 120V VERSION 120/208-240V VERSION Requires 3-wire, grounded service rated 120/240 volts ac, 20 amp, single phase, 60 Hz. ELE ...

  • Bunn CWTF APS-DV - page 6

    Page 6 1. Flush the water line and securely attach it to the inlet flare. 2. Turn on the water supply. 3. On faucet models, place an empty vessel beneath the faucet and lift the handle until water is dispensed. PLUMBING REQUIREMENTS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa ...

  • Bunn CWTF APS-DV - page 7

    Page 7 36102 090203 INITIAL SET -UP CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails. 2. Place an empty dispenser under the funnel. 3. Place the heater switch at the rear of the brewer in the "OFF" (lowe ...

  • Bunn CWTF APS-DV - page 8

    Page 8 36102 090203 2. Setting batch sizes. To set a batch volume, first check that the SET/LOCK switch is in the "SET" position on the circuit board. Press and hold the ST ART or BREW switch until three distinct clicks are heard, and then release the switch. (Failure to release the switch within two seconds after the third click causes t ...

  • Bunn CWTF APS-DV - page 9

    Page 9 36102 090203 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department. • Inspection, testing, and repair of electrical equipment should be perf ...

  • Bunn CWTF APS-DV - page 10

    Page 10 36102 090203 TROUBLESHOOTING (cont.) PROBLEM Brew cycle will not start (cont.) Water is not hot PROBABLE CAUSE REMEDY 5. Timer 6. Solenoid Valve 7. Water strainer/flow control (.222 GPM) 1. Tank Heater Switch 2. Limit Thermostat CAUTION - Do not eliminate or bypass limit thermostat. Use only replacement part #29329.1000 3. Control Thermosta ...

  • Bunn CWTF APS-DV - page 11

    Page 11 36102 090203 TROUBLESHOOTING (cont.) PROBLEM Inconsistent beverage level in dispenser Consistently low beverage level in the dispenser Spitting or excessive steaming PROBABLE CAUSE 1. Strainer/flow control (.222 GPM) 2. Syphon System 3. Lime Build-up CAUTION - Tank and tank compo- nents should be delimed regularly depending on local water c ...

  • Bunn CWTF APS-DV - page 12

    Page 12 36102 090203 TROUBLESHOOTING (cont.) PROBLEM Spitting or excessive steaming (cont.) Dripping from sprayhead Water flows into tank continuously (ON/OFF Switch "ON") Water flows into tank continuously (ON/OFF Switch "OFF") Beverage overflows dispenser PROBABLE CAUSE 2. Control Thermostat 1. Syphon System 2. Lime Build-up C ...

  • Bunn CWTF APS-DV - page 13

    Page 13 36102 090203 TROUBLESHOOTING (cont.) PROBLEM Weak beverage Dry coffee grounds remain in the funnel Brewer is making unusual noises PROBABLE CAUSE 1. Filter Type 2. Coffee Grind 3. Sprayhead 4. Funnel Loading 5. Water Temperature 1. Funnel Loading 1. Solenoid 2. Plumbing Lines 3. Water Supply REMEDY BUNN ® paper filters must be used for pro ...

  • Bunn CWTF APS-DV - page 14

    Page 14 36102 090203 TROUBLESHOOTING (cont.) PROBLEM Brewer is making unusual noises (cont.) Low beverage serving tempera- ture (CWTF Only) PROBABLE CAUSE 4. Tank Heater(s) 1. Warmer REMEDY Remove and clean lime off the tank heater(s). See page 20 Refer to Service - Warmer ele- ment for testing procedures. See page 29 ...

  • Bunn CWTF APS-DV - page 15

    Page 15 ...

  • Bunn CWTF APS-DV - page 16

    Page 16 SERVICE (cont.) CONTROL THERMOSTAT Location: The control thermostat is located inside the trunk on the upper left side of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Locate the blue wire on the control thermostat. 3. With a voltmeter, check the voltage across the blue wire on the control thermo ...

  • Bunn CWTF APS-DV - page 17

    Page 17 ...

  • Bunn CWTF APS-DV - page 18

    Page 18 ...

  • Bunn CWTF APS-DV - page 19

    Page 19 Location: The solenoid valve is located inside the trunk on the lower center part of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect both wires from the solenoid valve. Connect the brewer to the power source. With the lower warmer "ON/OFF" switch in the "ON" (upper) p ...

  • Bunn CWTF APS-DV - page 20

    Page 20 SERVICE (cont.) START SWITCH ...

  • Bunn CWTF APS-DV - page 21

    Page 21 TANK HEATERS Location: The tank heaters are located inside the tank and secured to the tank lid. Test Procedures: With Voltage selector switch set to 120V: 1. Disconnect the brewer from the power supply. 2. With a voltmeter, check the tank heater voltage across the white wire from the terminal block and black wire from the tank heater. Conn ...

  • Bunn CWTF APS-DV - page 22

    Page 22 SERVICE (cont.) 36102 090203 15. Reconnect the wires to the limit thermostat and tank heaters and control thermostat. See Limit Thermostat and Control Thermostat sections in this manual when reconnecting wires. 16. Install fill basin, secure with tank inlet fitting and gasket. Insert water supply line through grommet in fill basin. 17. Refe ...

  • Bunn CWTF APS-DV - page 23

    Page 23 SERVICE (cont.) TANK HEATER SWITCH ...

  • Bunn CWTF APS-DV - page 24

    Page 24 SERVICE (cont.) P1135 TANK HEATER SWITCH (cont.) 13. Remove the plastic facenut, hex facenut and the switch indicator/guard bracket that secures tank heater switch to the rear of the brewer. Remove switch and discard. 14. Insert new tank heater switch through the hole in the upper left rear of the trunk and secure with switch indicator/guar ...

  • Bunn CWTF APS-DV - page 25

    Page 25 36102 090203 FIG. 16 VOLTAGE SELECTOR SWITCH P2759.40 White/Violet to Tank Heater Blue to Tank Heater White to Terminal Block FIG. 17 VOLTAGE SELECTOR SWITCH TERMINALS SERVICE (cont.) VOLTAGE SELECTOR SWITCH - DV models only P2504 Location: The voltage selector switch is located on the component mounting bracket behind the front access pane ...

  • Bunn CWTF APS-DV - page 26

    Page 26 THERMAL FUSES ...

  • Bunn CWTF APS-DV - page 27

    Page 27 SERVICE (cont.) DIGITAL TIMER FIG. 20 DIGITAL TIMER ...

  • Bunn CWTF APS-DV - page 28

    Page 28 SERVICE (cont.) To increase a brew volume, place the ON/OFF switch in the “ON” position, press and hold the ST ART switch until three clicks are heard. Release the switch and press it again one or more times. (Failure to re- lease the switch within two seconds after the third click causes the volume setting to be aborted and pre- vious ...

  • Bunn CWTF APS-DV - page 29

    Page 29 SERVICE (cont.) WARMER ELEMENT(S) Location: The warmer elements are located under the warmer plates. Test Procedures: 1. Disconnect the brewer from the power source. 2. With a voltmeter, check voltage across the white wire from the terminal block and the wire from the "ON/OFF" switch to the warmer element with the "ON/OFF&quo ...

  • Bunn CWTF APS-DV - page 30

    Page 30 36102 090203 T1 T5 T3 T4 T2 BLK-14 BLK-14 120V AC 2 WIRE 120/208V AC 3 WIRE 120/240V AC 3 WIRE SINGLE PHASE WHI-14 WHI WHI WHI WHI/RED WHI/RED WHI/RED WHI WHI WHI WHI WHI WHI WHI WHI WHI/GRN WHI/BLU WHI/VIO-14 BLU-14 RED-14 TANK HEATER 1320 W 1800 W TANK HEATER SELECTOR SWITCH 10836.0009A 02/03 ©2003 BUNN-O-MATIC CORPORATION BLK BLK BLK BR ...

  • Bunn CWTF APS-DV - page 31

    Page 31 36102 090203 T1 T5 T3 T4 T2 BLK-14 BLK-14 120V AC 2 WIRE 120/208V AC 3 WIRE 120/240V AC 3 WIRE SINGLE PHASE WHI-14 WHI WHI WHI/RED WHI/RED WHI WHI/GRN WHI/BLU WHI/VIO-14 BLU-14 RED-14 TANK HEATER TANK HEATER SELECTOR SWITCH 10836.0010A 10/02 ©2001 BUNN-O-MATIC CORPORATION BLK BLK BLK BLK BLU BLU WHI/RED WHI HEATER SWITCH ON/OFF SWITCH L1 B ...

メーカー Bunn カテゴリー Coffeemaker

Bunn CWTF APS-DVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CWTF APS-DVの取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn CWTF APS-DVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn CWTF APS-DVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn CWTF APS-DVの取り付け説明書、サービスマニュアル、簡易説明書、またはBunn CWTF APS-DVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn CWTF APS-DVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn CWTF APS-DVデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn CWTF APS-DVを使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn CWTF APS-DVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn CWTF APS-DVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn CWTF APS-DVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn CWTF APS-DVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn CWTF APS-DVデバイスの基本機能を使うにあたってのヒント。 Bunn CWTF APS-DVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn CWTF APS-DVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn CWTF APS-DVのメーカー/サービスへの連絡先に関する情報。

Bunn CWTF APS-DVについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn CWTF APS-DVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn CWTF APS-DVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)