-
SmartPool Inc PE13 - page 1
T able of contents Impor tant - Please read first Rectangular or ov al pools Round pools Installation P ool Side Alarm T ransmitter Assemb ly Batter y Installation Low Batter y Indication T urn The Unit ON T urn The Unit OFF Reset The Unit Sensor Calibration T est The Unit RF (Radio F requency) Signal Link T esting T ransmitter channel A/B Select R ...
-
SmartPool Inc PE13 - page 2
IMPOR T ANT - Please read fir st THIS PR ODUCT DOES NO T REPLA CE THE NEED FOR ADUL T SUPER VISION OF ALL PERSONS IN THE POOL AREA. IT I S NO T A LIFE SA VING DEVICE. I T I S AN AID TO A MUL TI LEVEL PROGRAM OF POOL SAFETY INCLUDING ADUL T SUPER VISION, KNO WLEDGE OF CPR AND SWIMMING INSTRUCTION FOR ALL PERSONS USING THE POOL. IT IS INTENDED FOR US ...
-
SmartPool Inc PE13 - page 3
ALARM If the water returning from the filter is positioned at 6 oícloc k and the flow is countercloc k- wise, the best location to put the alarm is between 8 oícloc k to 9 oícloc k position. On the other hand, if the flow is clockwise , the alar m should be placed between 3 oícloc k to 4 oícloc k position. ALARM RETURN from filter Round pools ...
-
SmartPool Inc PE13 - page 4
Installation 1. T ak e to p seat cap of pool off and remov e t h e screws holding one end of the top seat 2. Lift up one en d of the top s e at of pool 3. Hang the sensor tube onto the guide rail. Ba c k of the sensor unit should rest against the inside of pool wall. 4. For wider guide r ail, mov e th e stain- less brac k et f orward by r e moving ...
-
SmartPool Inc PE13 - page 5
Sensitivity Adjust Loosen the two scre ws on the bottom of the sensor . Mov e t h e plastic piece with the pointer pointed to ìHî i f you want higher sensitivity or to ìL î if you want low er sensitivity . The unit is preset at factory to ìHî. If you ha v e to pl ace the unit near the return, snap the cap onto the sensor cage facing the direc ...
-
SmartPool Inc PE13 - page 6
Using t h e base as a template, drill 3 holes of 1/8" diameter on the top seat. Mount the unit onto the top seat as shown (right). Battery Installation The pool side alarm is designed to be powered by a standard 9V alkaline batter y . After installing batter y , pr ess the TEST b utton located at the front on the control unit. The alarm will s ...
-
SmartPool Inc PE13 - page 7
T urn the unit ON Press the green ON button and the unit will sound one shor t beep to indicate it is on. The alar m siren will sound when the sensor picks up any water wave motion. Therefore you should wait a few minutes for the water wave to settle down before turning on the unit. If the alarm goes off immediately after you hit this green ON butt ...
-
SmartPool Inc PE13 - page 8
Alarm unit function test Fill a 5 Gal pail 1/3 full with water and drop the pail from a height of a fe w inches from the surface of w ater . The wa ve created should activ ate the alar m. I f t h is test is unsucessful, adjust the sensitivity (ref er to Sensitivity Adjust section). Between each weight dr op test, y ou should turn the unit OFF . The ...
-
SmartPool Inc PE13 - page 9
RF (radio frequency) signal link testing This unit provides a con venient RF link test, to ensure good RF transmission without setting off the alar m. Hit the T E ST button and hold f or a couple of seconds. The unit will sound one beep or fiv e consecutive beeps . This will depend on whether the unit is set to ON or OFF . C o ntinue to hold this T ...
-
SmartPool Inc PE13 - page 10
T ransmitter Channel A/B select The pool side alar m RF (radio frequency) signal can be transmitted from the transmitter to the receiv er inside the house by t w o diff erent channels (A or B). Al l units are preset at channel A in the factory . Howe v er , i f your alar m system interf eres your neighborí s alar m system, you ma y hav e to ch ang ...
-
SmartPool Inc PE13 - page 11
Remote receiver Place the remote receiv er inside your house b ut close to the pool side alarm unit and a t a s traight line of sight. D O N O T place the unit near large metal objects or large motors , such as a r efr iger ator , or w ashing machine . This will adv ersely aff ect the RF reception Plug in the A/C adapter and the green LED will sta ...
-
SmartPool Inc PE13 - page 12
Back up po wer The receiver unit is designed to use a regular alkaline 9V batter y as bac k up power source. T o in stall this back up batter y , r e move t h e 4 screws and open the ba ttery door . 9V alkaline battery Back up po wer Ho w to connect to y our home security system The remote receiv er has a three ju nction te r minal b loc k, so that ...
-
SmartPool Inc PE13 - page 13
- A B GN PW O/P A/C adapter power jac k Channel A/B select switc h Commmon Normal Close Normal Open + K-1 Relay Ext. Connection Receiver Circuit Board The ter minal b lock signal s witching is controlled by m i croprocessor . For current switching, it is recommended to connect a K-1 type rela y (not included) to the ter minal b lock as sho wn. ...
-
SmartPool Inc PE13 - page 14
T rouble Shooting Q . The alarm unit gives frequent false alarms Check the sensitivity setting. The sensitivity may be set too high. The sensor can detect any water disturbance including the flow from the filter pump . Pl ace the alar m unit aw a y fr om the retur n, or put a deflector cap on the sensor cage . . ve signal Q A l arm unit cannot dete ...
-
SmartPool Inc PE13 - page 15
Q . The receiver cannot receive RF alarm signal. When the blue RESET b utton on the front is pressed, the unit is disab led for 10 seconds . Du ring this 10 seconds, it will not receiv e any RF signal. This allows y ou enough time to go to the poolside to turn off or reset the poolside alar m. Chec k the channel A or B select. Ma ke sure e v er y u ...
SmartPool Inc PE13についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもSmartPool Inc PE13の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSmartPool Inc PE13で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。