日本語 dropdown-ico

MTD 050 thru 062の取扱説明書

20ページ 1.5 mb
ダウンロード

ページに移動 of 20

Summary
  • MTD 050 thru 062 - page 1

    IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 20” and 22” RO T A R Y MO WERS Model Ser ies 050 thr u 062 PRINTED IN U .S.A. FORM NO .770-8550A Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest ...

  • MTD 050 thru 062 - page 2

    2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR LAWN MOWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY R ...

  • MTD 050 thru 062 - page 3

    3 • Do not engage the self-propelled mechanism on units so equipped while starting engine. • The blade control handle is a safety device. Never attempt to bypass its operation. Doing so makes the safety device inoperative and may result in personal injury through contact with the rotating blade. The blade control handle must operate easily in b ...

  • MTD 050 thru 062 - page 4

    4 • To reduce fire hazard, keep mower free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage. Allow mower to cool at least 5 minutes before storing. • Before cleaning, repairing, or inspecting, make certain the blade and all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the spark ...

  • MTD 050 thru 062 - page 5

    5 15 ° SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST FOLD ON DOTTED LINE, REPRESENTING A 15 ° SLOPE USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A ri ...

  • MTD 050 thru 062 - page 6

    6 SECTION 2: CONTENTS OF HARDWARE PACK Remove this sheet from your operator’s manual and lay the hardware on the illustration for identification purposes. After Assembly, keep the Slope Gauge which is on the reverse side of this sheet for future use. (Hardware pack may contain extra items which are not used on your unit. Part numbers are shown in ...

  • MTD 050 thru 062 - page 7

    7 SECTION 3: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new walk behind. It will help you assemble, prepare and maintain your walk behind. Please read and understand what it says. Before you start to prepare your walk behind for its first use, please locate the model plate and copy the information from it in thi ...

  • MTD 050 thru 062 - page 8

    8 SECTION 6: ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. NOTE: Reference to right or left hand side of the mower is observed from the operating position. This owner’s guide covers various model ...

  • MTD 050 thru 062 - page 9

    9 NOTE: If the control handle is disassembled from the upper handle for any reason, assemble the control handle by inserting the ends into the holes on each side of the upper handle. The hole in the control handle must be on the left side of the upper handle, and control handle must touch the upper handle when engaged (squeezed against the upper ha ...

  • MTD 050 thru 062 - page 10

    10 3. Place one smaller cupped washer on axle bolt, with the cupped side of washer toward the deck (away from wheel). NOTE: If the lowest cutting position (highest hole in the deck) is used, it is necessary to place the larger washer on the outside of the deck and the smaller washer on the inside. 4. Secure wheel to deck with one larger cupped wash ...

  • MTD 050 thru 062 - page 11

    11 SECTION 8: OPERATION Keep hands and feet away from the chute area on cutting deck. See Figure 1, Warning Label. The operation of any lawn mower can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields. We recommend wide vision safety mask for over spectacles or sta ...

  • MTD 050 thru 062 - page 12

    12 SECTION 9: ADJUSTMENTS WARNING: Do not at any time make any adjustment to lawn mower without first stopping engine and disconnecting spark plug wire. CUTTING HEIGHT ADJUSTMENT Adjustment may be made by removing and moving axle bolts to desired position. Cutting heights will be raised as axle bolts are moved to a lower hole and lowered as axle bo ...

  • MTD 050 thru 062 - page 13

    13 When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the mower and could break, causing personal injury. Th ...

  • MTD 050 thru 062 - page 14

    14 SECTION 13: TROUBLE SHOOTING GUIDE **Self-propelled models only Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Actions Engine f ails to star t Blade control handle disengaged. Spark plug wire disconnected. Dir ty aircleaner . Primer button not depressed. ...

  • MTD 050 thru 062 - page 15

    15 Model 050 thru 062 ...

  • MTD 050 thru 062 - page 16

    16 Model 050 thru 062 REF . NO . PA R T NO . DESCRIPTION 1 734-1779 Wheel Ass’y . Comp . (050 Series) 734-1780 Wheel Ass’y . Comp. (060 Ser ies) 2 742-0640 20 “ Blade 742-0642 22” Blade - Std. 742-0742 22” Mulching Blade 3 712-0324 He x L-Nut 1/4-20 Thd. 4 710-1044 He x Bolt 3/8-24 x 1.5” Lg. 5 753-0588 Blade Adapter Kit 6 738-0533 Axle ...

  • MTD 050 thru 062 - page 17

    17 NOTES ...

  • MTD 050 thru 062 - page 18

    18 NOTES ...

  • MTD 050 thru 062 - page 19

    19 ...

  • MTD 050 thru 062 - page 20

    20 MANUF A CTURER’S LIMITED W ARRANTY For ONE YEAR from the date of retail purchase within the United States of America, its possessions and territories, the manufacturer will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty covers unit ...

メーカー MTD カテゴリー Lawn Mower

MTD 050 thru 062のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 050 thru 062の取扱説明書
- MTDの製品カード
- パンフレット
- またはMTD 050 thru 062の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、MTD 050 thru 062の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、MTD 050 thru 062の取り付け説明書、サービスマニュアル、簡易説明書、またはMTD 050 thru 062のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、MTD 050 thru 062の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

MTD 050 thru 062デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMTD 050 thru 062を使用するのを助ける技術的文書のことです。説明書は通常、全てのMTD 050 thru 062ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

MTDの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. MTD 050 thru 062の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMTD 050 thru 062の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。MTD 050 thru 062に関してこのドキュメントで見つけることができる全てのヒントの目次
3. MTD 050 thru 062デバイスの基本機能を使うにあたってのヒント。 MTD 050 thru 062のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。MTD 050 thru 062に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMTD 050 thru 062のメーカー/サービスへの連絡先に関する情報。

MTD 050 thru 062についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもMTD 050 thru 062の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMTD 050 thru 062で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)