-
Delta 31-750 - page 1
INSTRUCTION MANUAL Bench Random Orbit a l Sander (Model 31-750) REVISED 3-29-99 P A R T NO. 1348132 'Delt a International Machinery Corp. 1999 ...
-
Delta 31-750 - page 2
2 T ABLE O F CONTENTS SAFETY RULES F O R AL L T OOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ADDITIONAL SAFETY RULES FOR A L L T OOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 U N P ACKING A N D CLEANING . . . . . . . . . . . . ...
-
Delta 31-750 - page 3
3 SAFETY RULES W oodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery , there are cert a in hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the pos si - bility of personal injury . However , i f normal safety precautions ar ...
-
Delta 31-750 - page 4
4 ADDITIONAL SAFETY RULES FOR RANDOM ORBIT A L SANDERS 1 . W ARNING: D O N O T operate your random orbit a l sander until it is completely assembled and inst alled according to the instructions . 2 .I F Y O U A R E N O T thoroughly familiar with the oper - ation of the random orbit a l sander , o b t ain advice from your supervisor , instructor or ...
-
Delta 31-750 - page 5
5 Fig. 2 Fig. 3 A Four Legs - 27-1/2 long B T wo Upper Front and Rear Braces - 1 1-1/2 long C T wo Upper Side Braces - 21-5/16 long D T wo Lower Front and Rear Braces - 17-1/8 long E T wo Lower Side Braces - 26-5/8 long F M 8 Hex Nut s - (36) G 3 / 8 Flat W ashers - (40) H M8 x 16mm Carriage Bolt s - (32) J M8 x 45mm Hex Head Screws (4) K Plastic F ...
-
Delta 31-750 - page 6
6 Fig. 4 Fig. 5 Fig. 7 Fig. 6 HOOK AND LOOP If you are using the hook and loop backed abrasive disc, simply position hook and loop abrasive disc (A) Fig. 4, directly onto disc plate p ad (B). ASSEMBLING ABRASIVE DISCS T O DISC PLA T E IMPORT A N T : MAKE CERT A I N THE MACHINE I S D I S - CONNECTED FROM T H E POWER SOURCE. There are two types of 9 ...
-
Delta 31-750 - page 7
7 Fig. 8 Fig. 9 2 . If an adjustment is necessary , loosen four lock nut s located underneath the t able, three of which are shown at (F) Fig. 8. 3 . W ith allen wrench supplied, tighten or loosen adjust - ment screws (D) and (E) Fig. 9, as necessary . Recheck t h e t able height and repeat the adjustment if needed, u n t i l t h e t able surface i ...
-
Delta 31-750 - page 8
8 Fig. 13 Fig. 12 ASSEMBLING DUST B A G 1 . A 1-1/2 I.D. dust chute (A) Fig. 12, is supplied with the spindle sander to accept the dust bag. 2 . T o assemble the dust bag (B) Fig. 13, over the dust chute (A), simply squeeze the spring clamp on the dust bag and assemble it over the dust chute as shown. Fig. 14 ASSEMBLING ACCESSOR Y 50-780 ST A N D 1 ...
-
Delta 31-750 - page 9
9 CONNECTING SANDER T O POWER SOURCE POWER CONNECTIONS A s e p arate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be protected with a 20 Amp fuse. Have a certified electrician replace or rep air a worn cord immediately . Before connecting the motor to a power line, make sure the switch i ...
-
Delta 31-750 - page 10
10 Fig. 19 Fig. 18 GROUNDED OUTLET B O X CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST O F THE 3 BLADES GROUNDED OUTLET B O X GROUNDING MEANS ADAPTER In the event of a malfunction or breakdown, grounding provides a p ath of least resist ance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord ...
-
Delta 31-750 - page 11
11 OPERA TING CONTROLS AND ADJUSTMENTS Fig. 21 Fig. 22 S T ARTING A N D S T OPPING SANDER The on/of f switch (A) Fig. 21, is located on the sander base. T o turn the sander ON move the switch to the up p o s i t i o n . T o turn the sander OFF move the switch to the down position. LOCKING SWITCH IN THE OFF POSITION W e suggest that when the sander ...
-
Delta 31-750 - page 12
12 OPERA TIONS PLEASE READ THE SAFETY RULES BEFORE OPERA TING THE SANDER. The random orbit al sander can be used with or without the fence depending on the application; however, w e recommend that the fence be used whenever possible. Fig. 25 Fig. 27 Fig. 26 Fig. 25, illustrates a typical edge sanding operation using the fence as a backstop. Fig. 26 ...
Delta 31-750についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもDelta 31-750の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 31-750で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。