Pelco DX8000の取扱説明書

20ページ 5.35 mb
ダウンロード

ページに移動 of 20

Summary
  • Pelco DX8000 - page 1

    DX8000-256RAM Installation Manual C1602M (6/04) Digital Video Recorder DX8000 ...

  • Pelco DX8000 - page 2

    Protecting people and property in a million locations worldwide. ...

  • Pelco DX8000 - page 3

    C1602M (6/04) 1 Introduction The following instructions serve as a guide for the installation of the DX8000-256RAM memory expansion module. PARTS LIST Qty Description 1 256 MB double data rate (DDR) dual inline memory module (DIMM) 1 Adhesive-backed upgrade part label Figure 1. 256 MB DIMM Module TOOLS NEEDED 1 Phillips-head screwdriver #1 (nonmagn ...

  • Pelco DX8000 - page 4

    2 C1602M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and T ools Needed sections. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shutti ...

  • Pelco DX8000 - page 5

    C1602M (6/04) 3 Figure 3. Removing Power Cord from Unit ...

  • Pelco DX8000 - page 6

    4 C1602M (6/04) Figure 4. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective m ...

  • Pelco DX8000 - page 7

    C1602M (6/04) 5 Prepare Unit for RAM Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the uni ...

  • Pelco DX8000 - page 8

    6 C1602M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section. a. Remove the two top-most screws on the left and right side panels of the DX8000. Ref ...

  • Pelco DX8000 - page 9

    C1602M (6/04) 7 COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity . Figure 6. DX8000 Interior POWER SUPPLY DIMM SOCKETS (RAM) CPU VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE FRONT CROSS-BRA ...

  • Pelco DX8000 - page 10

    8 C1602M (6/04) Install the DX8000-256RAM Memory Module 1. Carefully remove the DX8000-256RAM DIMM module from its static-safe packaging. Handle the DIMM by its edges and avoid contact with the module’ s chips or conductive leads. 2. Locate the first empty DIMM socket. This socket is directly adjacent to the socket containing the existing DIMM mo ...

  • Pelco DX8000 - page 11

    C1602M (6/04) 9 3. Align the DIMM module with the socket so that the notch in the module lines up properly with the break in the DIMM socket. Refer to Figure 8. 4. Make sure that the white retaining clips are not in the locked position by pressing outward and down on each clip. Refer to Figure 8. Figure 8. DIMM Module and DIMM Socket Alignment 3 4 ...

  • Pelco DX8000 - page 12

    10 C1602M (6/04) 5. Carefully , but firmly , push the DIMM module into the empty socket until it is properly seated. The module is properly seated when the retaining clips snap back into place as in Figure 9. NOTE: When inserting the DIMM module into the socket, use enough pressure to ensure that the retaining clips snap back into place. Be careful ...

  • Pelco DX8000 - page 13

    C1602M (6/04) 11 Reassemble the Unit 1. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 10. Figure 10. Replacing Chassis Cover ...

  • Pelco DX8000 - page 14

    12 C1602M (6/04) 2. Attach the silver part label that came in your upgrade kit to the inside of your DVR’ s front door . a. Remove the paper backing from the part label. b. Carefully place the label, adhesive-side down, on a free section of the inside of the door . c. Press down firmly to ensure that the label properly adheres to the inside of th ...

  • Pelco DX8000 - page 15

    C1602M (6/04) 13 3. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 4. Plug the power cord back into the power supply and then into the wall. 5. T urn on the power switch and allow the unit to start up and find the new memory . This may take several minutes. Figure 1 ...

  • Pelco DX8000 - page 16

    14 C1602M (6/04) V erify Installation of New RAM 1. After the DX8000 application starts, log in as an administrator level user and exit to the Windows ® operating system. Refer to the Installation or Operations and Programming manuals that came with your unit for instructions. 2. Go to Start > Settings > Control Panel. The Control Panel wind ...

  • Pelco DX8000 - page 17

    C1602M (6/04) 15 4 4. V erify that the amount of RAM is now 512 MB. Refer to Figure 15. Figure 15. System Properties Dialog Box 5. Click OK to exit the System Properties dialog box. 6. Go to Start > Programs > DX8000 to start the DX8000 application and return the unit to service. ...

  • Pelco DX8000 - page 18

    16 C1602M (6/04) Notes ...

  • Pelco DX8000 - page 19

    PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models ...

  • Pelco DX8000 - page 20

    C1602M (6/04) ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | ...

メーカー Pelco カテゴリー DVR

Pelco DX8000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DX8000の取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco DX8000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco DX8000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco DX8000の取り付け説明書、サービスマニュアル、簡易説明書、またはPelco DX8000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco DX8000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco DX8000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco DX8000を使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco DX8000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco DX8000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco DX8000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco DX8000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco DX8000デバイスの基本機能を使うにあたってのヒント。 Pelco DX8000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco DX8000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco DX8000のメーカー/サービスへの連絡先に関する情報。

Pelco DX8000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco DX8000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco DX8000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)