Extron electronic MPS 409の取扱説明書

43ページ 4.17 mb
ダウンロード

ページに移動 of 43

Summary
  • Extron electronic MPS 409 - page 1

    Media Presentation Switcher MPS 409 User Guide Switchers 68-1833-01 Rev. A 07 10 ...

  • Extron electronic MPS 409 - page 2

    This symbol is intended to alert the user of important operating and mainte- nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution Read Instructions ? ...

  • Extron electronic MPS 409 - page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference r eceived, including interfer ence that may cau ...

  • Extron electronic MPS 409 - page 4

    ...

  • Extron electronic MPS 409 - page 5

    v MPS 409 Switcher • Contents Introduction ........................................... 1 About This Manual .......................................... 1 About the MPS 409 ......................................... 1 Features ........................................................... 1 Installation ............................................. 4 Mo ...

  • Extron electronic MPS 409 - page 6

    MPS 409 Switcher • Contents vi ...

  • Extron electronic MPS 409 - page 7

    Intr oduction • About this User Guide • About the MPS 409 • Features About this User Guide This guide contains information to install, configure, and operate the Extr on Electr onics MPS 409, Media Presentation Switcher . In this guide, the MPS 409 may be referr ed to as “MPS”, “MPS 409” or “switcher”. About the MPS 409 The Extro ...

  • Extron electronic MPS 409 - page 8

    • Program audio switcher — A four input, one output ster eo audio switcher allows the audio input of any video group to be selected for the pr ogram audio output, with volume and mute control. The MPS 409 featur es balanced/unbalanced pr ogram audio output on a 5-pole captive screw connector . • Microphone/line input — One 3.5 mm captive sc ...

  • Extron electronic MPS 409 - page 9

    OUTPUT HDMI 3 1 2 OUTPUT 1 2 3 100-240V ~ 0.2A 50/60 Hz 2 1 OUTPUT OUTPUT VGA/YUV DVI-D 1 2 OUTPUT 1 2 OUTPUT 2 1 LEVEL MIC +48V LINE ON OFF MIC/LINE 1 2 ON + - + - - + R L PROGRAM AUDIO OUT MIC/LINE IN RS-232 Rx Tx OUTPUT 1 2 1 2 OUTPUT VIDEO L R R L R L XPA 1002 1 2 LIMITER/PROTECT SIGNAL OVER TEMP DISPLAY Ex t r on XP A 1 00 2 Pow er Ampl ier ...

  • Extron electronic MPS 409 - page 10

    Installation This section describes the installation and the operation of the MPS 409, including: • Mounting the Switcher • Rear Panel Connections • Cabling the MPS 409 Switcher Mounting the Switcher The MPS 409 is housed in 1U, full rack width metal enclosure rack- or desk-mountable. The MBD 149 1U through-desk and rack mounting kit (# 70-07 ...

  • Extron electronic MPS 409 - page 11

    3. Mechanical loading — Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven mechanical loading. 4. Circuit overloading — Connect the equipment to the supply cir cuit and consider the effect that cir cuit overloading might have on over current pr otection and supply wiring. Appropriate consideration of equ ...

  • Extron electronic MPS 409 - page 12

    Rear Panel Connections 50/60 Hz L R Tx MIC/LINE IN ON OFF MIC LINE LEVEL +48V ON 1 2 HDMI VIDEO VGA/YUV DVI-D OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT 1 2 L 1 2 1 2 1 2 1 2 1 2 1 2 3 3 1 2 L L R R R MIC/LINE PROGRAM AUDIO OUT Rx RS-232 OUTPUT 100-240V 0.4A MAX j k s t u a b c d f g h i e l n o p q r m Figure 3. MPS 409 Rear Panel a AC power ...

  • Extron electronic MPS 409 - page 13

    j Mic/Line input — One 3-pole captive screw connector switchable between mic and line level inputs. A two position DIP switch (u) selects mic or line input level. Connecting the 3-pole captive screw micr ophone connector 1. Use a pre-made 3-pole captive scr ew micr ophone cable, or cut bulk microphone cable, and attach the 3-pole captive scr ew c ...

  • Extron electronic MPS 409 - page 14

    q HDMI audio output — 3.5 mm stereo connector with audio output fr om the selected HDMI input. See figure 4 for wiring. r Composite video output — One BNC connector with selected composite video output for a composite video display device. s Composite audio output — One stereo pair of RCA connectors with audio output from the selected compos ...

  • Extron electronic MPS 409 - page 15

    Cabling the MPS 409 Switcher The MPS switcher can be connected to as many as 9 input devices simultaneously . It can output to as many as four devices (three in combine mode) simultaneously . Outputs can be configured for simultaneous outputs fr om each of the four input gr oups, VGA/YUV , DVI-D, HDMI, composite or one at a time from a selection o ...

  • Extron electronic MPS 409 - page 16

    Operation This section discusses how to connect, configure, and operate the MPS 409. T opics that are covered include: • Front Panel Featur es • Front Panel Operation • Program Audio • EDID Minder • HDCP Fr ont Panel Features 1 MODE 2 SINGLE 1 SEP ARA TE 2 COMBINE DVI/HDMI 1 2 1 2 3 MUTE MPS 409 DIGIT AL MEDIA PRESENT A TION SWITCHER VID ...

  • Extron electronic MPS 409 - page 17

    Microphone and Pr ogram Audio Controls h Mic Mute — T oggles the microphone mixer on and of f to provide micr ophone talk-over for the program audio. The LED (when lit) indicates the micr ophone input is muted. i Mic V olume — This adjustment knob controls the volume of the micr ophone. Rotating the Mic V olume control unmutes the microphone. j ...

  • Extron electronic MPS 409 - page 18

    Fr ont Panel Operation The MPS switcher can be connected to as many as nine input devices and four output displays plus an audio amplifier . It operates in one of four switching modes: single (the default), separate, single-combine, or separate-combine. The functions of the front panel contr ols ar e described in the following sections. Each input ...

  • Extron electronic MPS 409 - page 19

    Input Selection — Single Switcher Mode In single switcher mode (default) the switcher emulates a single nine input switcher (9x1). In this mode, when an input is selected from any gr oup, the gr een LED indicator to the right of the button lights, and the selected input (video and audio) is routed to the output for that group. The selected audio ...

  • Extron electronic MPS 409 - page 20

    Combine Mode Combine mode switches a selected HDMI/DVI input to the HDMI output, deactivating the DVI audio and video outputs. This enables the MPS 409 to function as one 5x1 HDMI/DVI and audio switcher , adding VGA/YUV and Video inputs. Combine mode can be used whether the switcher is in separate or single switch mode. All other inputs and outputs ...

  • Extron electronic MPS 409 - page 21

    Pr ogram Audio The selected audio input is routed to the pr ogram audio output accor ding to the switcher mode. The input LED selected for program audio output blinks. Program Audio Selection Single switcher mode In single switcher mode, audio from the selected input is r outed to the pr ogram audio output. If combine mode is active, when a DVI inp ...

  • Extron electronic MPS 409 - page 22

    Audio Gain and Attenuation Adjustments Individual audio inputs can be adjusted over a range of -18 dB to +24 dB using the program audio mute button and program audio volume contr ol knob. These adjustments can be used to normalize the input audio levels so that output volume is consistent for all inputs. The front panel input LEDs pr ovide a status ...

  • Extron electronic MPS 409 - page 23

    Microphone Contr ols Mic on/off Mic volume and mute are contr olled fr om the front panel. The Mic mute button toggles the Mic input on or off. The corr esponding r ed LED illuminates when Mic volume has been shut off (muted). When the Mic input is enabled it is mixed with the program audio output. Mic volume is a stepped encoder , adjusted at a ra ...

  • Extron electronic MPS 409 - page 24

    EDID Minder The DVI and VGA/YUV groups featur e EDID Minder , ensuring that each input source reads the EDID of the output display even when not selected. The result is the video sour ce powers up properly and r eliably outputs content when selected. The EDID r emains in the selected mode (automatic or user assigned) even after loss of power . The ...

  • Extron electronic MPS 409 - page 25

    User assigned EDID Mode — Using SIS commands, an EDID file can be selected from a table of 19 EDID files. One additional EDID file location is reserved for user -loaded EDID files for the VGA and DVI groups. Once a user assigned EDID is chosen, the switcher stor es it at the inputs and no longer polls for the EDID of a connected display . The ...

  • Extron electronic MPS 409 - page 26

    SIS Pr ogramming and Contr ol This section discusses SIS programming and contr ol of the MPS 409 including: • Connection Options • Host-to-MPS Communications • Command/Response T able • Updating Firmware Connection Options The MPS 409 can be remotely connected via a host computer or other device (such as a control system) attached to the r ...

  • Extron electronic MPS 409 - page 27

    USB Configuration Port Drivers for the MPS 409 USB configuration port are loaded automatically when Dataviewer or Firmware Loader , included on the software disc or available at www .extron.com , ar e loaded. Host-to-MPS Communications The MPS switcher accepts Simple Instruction Set (SIS ™ ) commands through the RS-232 or USB configuration por ...

  • Extron electronic MPS 409 - page 28

    Command/Response T able Using the Command/Response T able The command/response table is shown on the following pages. Lower case characters ar e acceptable in the command field only where indicated. Symbols ar e used thr oughout the table to repr esent variables in the command/r esponse fields. Symbol definitions and an ASCII-to-hexadecimal (HEX ...

  • Extron electronic MPS 409 - page 29

    Command/response table for SIS commands Command ASCII Command (host to switcher) Response (switcher to host) Description Switcher- initiated messages Input selection (in separate switcher mode only) Select video and audio input X! * X@ ! Chn X! * X@ ] Group X! and input X@ are selected. X! = Group 1 thr ough 4 (1 = VGA, 2 = DVI, 3 = HDMI, 4 = Compo ...

  • Extron electronic MPS 409 - page 30

    Command ASCII Command (host to switcher) Response (switcher to host) Description Switcher- initiated messages Program audio ducking level in talk over mode Adjust audio ducking level X1@ * 58# Adl X1@ ] Adjusts how much ( X1@ = 0 to 30 dB) the program audio ducks (automatically decreases) in talk over mode. 0 = ducking off. Increment audio ducking ...

  • Extron electronic MPS 409 - page 31

    Command ASCII Command (host to switcher) Response (switcher to host) Description Switcher- initiated messages Status command of Mic DIP switches Read status of DIP switch positions 41S X1* • X1(] X1* = 48V phantom power (0=off, 1=on) X1( = Mic/Line input (0=Mic, 1=Line) Front panel security lockout (executive mode) Lock front panel access 2X/x Ex ...

  • Extron electronic MPS 409 - page 32

    EDID NOTES: EDID Minder is only supported on the VGA and DVI video groups. Attempting to assign an EDID file to the HDMI or composite video group ( X! = 3 or 4) will give an err or (E13). In DVI/HDMI input combine mode, the DVI inputs are r outed to the HDMI output. The EDID of the HDMI output is used for the DVI group inputs when DVI/HDMI combine ...

  • Extron electronic MPS 409 - page 33

    EDID Format Cross-r eference T able X1^ Native Resolution Refresh Pixel Clock 0 Automatic Mode 1 800 x 600 60 Hz 40 MHz 2 1024 x 768 60 Hz 65 MHz 3 1280 x 768 60 Hz 79.5 MHz 4 1280 x 800 60 Hz 83.5 MHz 5 1280 x 1024 60 Hz 108 MHz 6 1360 x 768 60 Hz 85.5 MHz 7 1440 x 900 60 Hz 106.5 MHz 8 1400 x 1050 60 Hz 121.75 MHz 9 1680 x 1050 60 Hz 119 MHz 10 1 ...

  • Extron electronic MPS 409 - page 34

    3. From the toolbar , select File > Open . 4. Locate the downloaded firmware file and click to select it. 5. Click Begin on the main screen. The total pr ogr ess bar tracks the loading progr ess. 6. When the T ransfer Complete! message appears, the upload is finished. Exit the program by selecting File > Exit . Updating Firmwar e The Firmw ...

  • Extron electronic MPS 409 - page 35

    Refer ence Information This section discusses the specifications, part numbers, and accessories for the MPS 409. T opics that are cover ed, include: • Specifications • Part Numbers and Accessories • Cables and Connectors Specifications Video — VGA Gain ............................................... Unity Bandwidth ...................... ...

  • Extron electronic MPS 409 - page 36

    Connectors VGA inputs .............................. 2 female 15-pin HD DVI inputs ................................ 2 female DVI-I HDMI inputs ............................ 3 female HDMI type A Composite video inputs ........... 2 female BNC Nominal level VGA inputs .............................. 1.0 Vp-p for Y of component video 0.7 Vp-p for RGB an ...

  • Extron electronic MPS 409 - page 37

    Input impedance ............................ 510 ohms Output impedance ......................... 75 ohms Max. input voltage ......................... 5.0 Vp-p Max. propagation delay .................. 30 ns Max. rise/fall time ........................... 4.2 ns Polarity ........................................... Positive or negative (follows input ...

  • Extron electronic MPS 409 - page 38

    Audio output — program audio Number/signal type ........................ 1 stereo, balanced/unbalanced Connector ...................................... (1) 3.5 mm captive screw connector , 5-pole Impedance ..................................... 50 ohms unbalanced, 100 ohms balanced Gain error ...................................... ±0.1 dB channel ...

  • Extron electronic MPS 409 - page 39

    Regulatory compliance Safety ...................................... CE, c-UL, UL EMI/EMC ................................. CE, C-tick, ICES, FCC Class A, VCCI MTBF ............................................. 30,000 hours W arranty ........................................ 3 years parts and labor NOTE: All nominal levels are at ±10%. NOTE: Speci? ...

  • Extron electronic MPS 409 - page 40

    Part Numbers and Accessories Included Parts These items are included in each or der: Included parts Replacement part number MPS 409 60-1012-01 MBU 149 1U Full Rack Under -Desk Mount Kit 70-077-03 T weeker (small screwdriver) 3.5 mm, 3-pole captive screw connector (2) 3.5 mm, 5-pole captive screw connector IEC power cord MPS 409 Setup Guide Rubber f ...

  • Extron electronic MPS 409 - page 41

    Cables and Connectors When using signals with a scanning frequency of 15–125 kHz and running distances of 100 feet or more, use high r esolution BNC cables to achieve maximum performance. Pre-cut Cables VGA-A M-M MD with audio cable Part number Lengths from 3' to 50' 26-490- xx VGA M to BNC M MHR cable, SYM BNCM Series Part number Lengt ...

  • Extron electronic MPS 409 - page 42

    Assorted Connectors Crimp connectors (qty . = 50) Part number Mini HR, BNC Male 100-250-01 Gold Plated Male Center Pins for MHR BNC Connectors 100-256-01 Solder connectors (qty . = 10) Part number RCA-3502, RCA Male 100-333-01 RCA-HQ, RCA Male 100-334-01 1/4" Stereo Phone-HQ 100-332-01 3.5 mm Mini Stereo-HQ, Male Ster eo Audio 100-331-01 BNC c ...

  • Extron electronic MPS 409 - page 43

    Extr on ® W arranty Extron Electr onics warrants this pr oduct against defects in materials and workmanship for a period of three years from the date of pur chase. In the event of malfunction during the warranty period attributable dir ectly to faulty workmanship and/or materials, Extron Electr onics will, at its option, r epair or replace said pr ...

メーカー Extron electronic カテゴリー Switch

Extron electronic MPS 409のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MPS 409の取扱説明書
- Extron electronicの製品カード
- パンフレット
- またはExtron electronic MPS 409の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Extron electronic MPS 409の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Extron electronic MPS 409の取り付け説明書、サービスマニュアル、簡易説明書、またはExtron electronic MPS 409のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Extron electronic MPS 409の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Extron electronic MPS 409デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがExtron electronic MPS 409を使用するのを助ける技術的文書のことです。説明書は通常、全てのExtron electronic MPS 409ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Extron electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Extron electronic MPS 409の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははExtron electronic MPS 409の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Extron electronic MPS 409に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Extron electronic MPS 409デバイスの基本機能を使うにあたってのヒント。 Extron electronic MPS 409のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Extron electronic MPS 409に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるExtron electronic MPS 409のメーカー/サービスへの連絡先に関する情報。

Extron electronic MPS 409についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもExtron electronic MPS 409の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがExtron electronic MPS 409で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)