Humminbird HDR200の取扱説明書

14ページ 1.74 mb
ダウンロード

ページに移動 of 14

Summary
  • Humminbird HDR200 - page 1

    ...

  • Humminbird HDR200 - page 2

    TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefull y consider the following before installing your transducer. TRANSDUCER MOUNTING OPTIONS A. Transom Mount - The Humminbird hig ...

  • Humminbird HDR200 - page 3

    by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it back in place. (See Figure A) B. Inside Hull Mount - The high speed transducer can be mounted inside the hull (without pivot assembly) using the proper two - part epox ...

  • Humminbird HDR200 - page 4

    Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the center of the Bracket sl ots. On some aluminum boats it may be necessary to use a wood back - up plate. It is important to use a silicone sealant betwe ...

  • Humminbird HDR200 - page 5

    NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water lev el. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied. Be sure to align the holes so that they are ...

  • Humminbird HDR200 - page 6

    Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the h eaded pin and insert it through the two parts. Assemble by screwing the ¼”x3/8” allen head screw into the end of the pin a ...

  • Humminbird HDR200 - page 7

    wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly faste ned to the pivot. (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the bottom of the transom. ( ...

  • Humminbird HDR200 - page 8

    7. Remove the water and transducer and clean the m arked area and the bottom of the transducer thoroughly. 8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted. The puddle should be larger than the bo ttom of the transducer. 9. Coat the bot ...

  • Humminbird HDR200 - page 9

    Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilte d to any desired position. ...

  • Humminbird HDR200 - page 10

    OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommended since the unit cannot be rotated. INSTALLING THE CABLES Your LCR comes equipped with Humminbird’s n ...

  • Humminbird HDR200 - page 11

    It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”. Note: An adapter (AD - 4) is available to allow use of an old waterproof (BNC) transducer with the LCR, but be sure that the transducer is a 16degree ...

  • Humminbird HDR200 - page 12

    Installing the HDR 200 Before mounting the HDR 200, gather the parts you need: HDR 200, mounting hardware kit, and transducer cable. If the transducer cable is no t long enough for your installation, see “Accessories” earlier in this manula for information on the EC - 6 10’ extension. • The mounting surface should be adequately supported to ...

  • Humminbird HDR200 - page 13

    begin transmitting, and automatically display the digital depth. (If the HDR 200 is wired to a switch other than the ignition switch, turn that switch on.) Increase your boat speed to ensure that you get a continuous bottom reading as the boat moves. Your HDR 200 and its transducer are designed to operate at up to 75 mph. However, use caution when ...

  • Humminbird HDR200 - page 14

    Do not attempt to repair HDR 200 yourself. Repairs should be performed only by authorized Humminbird technicians. ...

メーカー Humminbird カテゴリー SONAR

Humminbird HDR200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HDR200の取扱説明書
- Humminbirdの製品カード
- パンフレット
- またはHumminbird HDR200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Humminbird HDR200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Humminbird HDR200の取り付け説明書、サービスマニュアル、簡易説明書、またはHumminbird HDR200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Humminbird HDR200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Humminbird HDR200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHumminbird HDR200を使用するのを助ける技術的文書のことです。説明書は通常、全てのHumminbird HDR200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Humminbirdの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Humminbird HDR200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHumminbird HDR200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Humminbird HDR200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Humminbird HDR200デバイスの基本機能を使うにあたってのヒント。 Humminbird HDR200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Humminbird HDR200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHumminbird HDR200のメーカー/サービスへの連絡先に関する情報。

Humminbird HDR200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHumminbird HDR200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHumminbird HDR200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)