Weider WESY92190の取扱説明書

28ページ 1.15 mb
ダウンロード

ページに移動 of 28

Summary
  • Weider WESY92190 - page 1

    USERÕS MANUAL Model No. WESY92190 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference. QUESTIONS? As a manufacturer , we are com- mitted to providing complet ...

  • Weider WESY92190 - page 2

    Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . ...

  • Weider WESY92190 - page 3

    3 W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. Import ...

  • Weider WESY92190 - page 4

    4 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 38 in. Length: 61 in. Low Pulley Station W arning Decal 2 Foot Plate Row Bar Console High Pulley Station Ab Pulley Station Leg Lever Butterfly Arm Press Arm Shroud W arning Decal 2 W arning Decal 2 (on both sides of the weight mechanism inside of the shroud) W arning Decal 1 Seat Backrest Thank you for ...

  • Weider WESY92190 - page 5

    5 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual. Place the chart on the floor and use it to quickly identify dif- ferent parts as you open the packages for each ...

  • Weider WESY92190 - page 6

    6 1. Before beginning assembly , make sure you have read and understood the information on page 5. Open the parts bag labeled ÒFRAME ASSEMBL Y .Ó Press a 2Ó Square Outer Cap (51) onto each end of the Stabilizer (5). Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up through the Stabilizer (5) and place it flat on the floor . 1 2. Press a 2Ó Squ ...

  • Weider WESY92190 - page 7

    7 4. Press a 2Ó Square Inner Cap (21) into each end of the crossbar on the T op Frame (1). Slide two 5/16Ó Flat W ashers (56) onto two 5/16Ó x 2 3/4Ó Bolts (67). Place the T op Frame (1) on top of the Front Upright (42) and align the indicated holes with the holes in the bracket on the Front Upright. Insert the 5/16Ó x 2 3/4Ó Bolts (67) throu ...

  • Weider WESY92190 - page 8

    8 10. Press a 1 1/2Ó Square Inner Cap (33) into the end of the Seat Frame (36). Insert two 5/16Ó x 2 3/4Ó Bolts (67) through the Support Plate (27) and the indicated holes in the Front Upright (42). Place the mounting bracket on the Seat Frame (36) over the two Bolts. T ighten a 5/16Ó Nylon Locknut (53) onto each Bolt. Make sure the Support Pla ...

  • Weider WESY92190 - page 9

    9 13 Lubricate 1 Bracket 47 21 4 3 45 Axle 4 3 45 13. Identify the Right Butterfly Arm (48) and the Left Butterfly Arm (47). Note the position of the welded bracket on each Arm. Arm identification is very important for this step. Lubricate both axles on the T op Frame (1). Slide the Right Butterfly Arm (48) onto the right axle. Note: Be careful not ...

  • Weider WESY92190 - page 10

    Cable Assembly 15. Open the parts bag labeled ÒCABLE ASSEMBL Y AND PULLEYS.Ó For Cable identification and rout- ing during steps 15Ð30, refer to the Cable Diagram and Cable ID Chart on page 19. Identify the High Cable (2). It is approximately 163 1/2Ó long. It is the shortest cable and it has a ball on each end. Wrap the end with the small ball ...

  • Weider WESY92190 - page 11

    11 19. Remove the 1/2Ó Nylon Locknut (68) from the welded hook on the T op Frame (1). Slide the Pulley Bracket (20) onto the hook and secure it with the Nylon Locknut. T ighten the Nylon Locknut, but make sure the Pulley Bracket can pivot freely . Remove the Pulley (35) from the Pulley Bracket (20). Wrap the High Cable (2) around the Pulley in the ...

  • Weider WESY92190 - page 12

    12 22. Remove the 3 1/2Ó Pulley (35) from the pre-assem- bled Adjustment Bracket (84). Wrap the High Cable (2) around the Pulley in the direction shown. Attach the Pulley to the Bracket with a 3/8Ó x 1 1/2Ó Bolt (60) and a 3/8Ó Nylon Jamnut (63). 22 35 63 2 84 60 23. Wrap the High Cable (2) around a 3 1/2Ó Pulley (35) Pulley in the direction s ...

  • Weider WESY92190 - page 13

    13 26. Move to the other side of the unit. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Front Upright (42) with a 3/8Ó x 3 3/4Ó Bolt (19), a Cable T rap (66), a 3/8Ó Flat W asher (55) and a 3/8Ó Nylon Jamnut (63). Make sure the Cable T rap (66) is positioned as shown and that the Pulley (3 ...

  • Weider WESY92190 - page 14

    31. Open the parts bag labeled ÒSEA T ASSEMBL Y .Ó Attach the Backrest (41) to the Front Upright (42) with two 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó Flat W ashers (90). Seat Assembly 41 43 43 90 42 30. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Front Upright (42) with a 3/8Ó x 3 3/4Ó ...

  • Weider WESY92190 - page 15

    15 34. Attach the Curl Pad (24) to the Curl Post (10) with two 1/4Ó x 3/4Ó Screws (17). Slide the Curl Post (10) onto the Seat Frame (36) so each of the welded brackets is between the Seat Frame and the bracket on the Leg lever (29). Secure the Curl Post with the 5/16Ó x 2Ó Knob (72). Make sure the Leg Lever (29) can be turned freely after the ...

  • Weider WESY92190 - page 16

    38a. The following instructions are critical to the cor- rect operation of your weight system. If the adjustment is incorrect, it can damage the motor . Make sure that you read and understand these instructions before attempting to adjust the Weight Mechanism (26). See page 20 for instructions on how to operate the console. Set the console to the m ...

  • Weider WESY92190 - page 17

    38e.See the inset drawing. Loosen the 3/8Ó Plain Nuts (85), and the 3/8Ó x 3Ó Bolt (88) so that the 3/8Ó x 4Ó T ap Screw (86) can rotate freely . Note: The T ap Screw must pivot freely . 38f. Check the brass piece that is pictured in drawing 38f. It should barely be touching the shaded area on the Weight Mechanism (26) and should move slightly ...

  • Weider WESY92190 - page 18

    18 41. Make sure that all parts have been properly tight- ened. The use of the remaining parts will be explained in HOW T O USE THE WEIGHT SYSTEM, beginning on page 20 of this manual. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly , f ...

  • Weider WESY92190 - page 19

    19 Cable Diagram The Cable Diagram below shows the proper routing of the High Cable (2) and the Low Cable (9). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly , that the Pulleys move smoothly , and that the Cable T raps do not touch or bind the Cables. Incorrect cable routing can damage the weight s ...

  • Weider WESY92190 - page 20

    20 How to Use the W eight System PLUGGING IN THE POWER CORD Plug in the power cord to a 120-volt outlet. Keep the power cord away from walkways and heated surfaces. T urn on the power when using the weight system, or the weight system could be damaged. When you are finished using the weight system, always unplug the power cord. IMPORT ANT : T o pre ...

  • Weider WESY92190 - page 21

    21 A TT ACHING THE LA T BAR, ROW BAR, AB STRAP OR HANDLE TO THE LOW , HIGH OR AB PULLEY ST A TION Attach the Lat Bar (76) to the Low Cable (9) with a Cable Clip (73). For some exercises, the Chain (74) should be attached between the Lat Bar and the Low Cable with two Cable Clips. Adjust the length of the Chain between the Lat Bar and the Cable so t ...

  • Weider WESY92190 - page 22

    22 31 63 66 35 Additional slack can be removed by using the Pulley Plates (31). The Pulley Plates have several sets of adjust- ment holes. By moving one or both pulleys to a different set of holes, the cables will be tightened. T o move a Pulley , remove the 3/8Ó Nylon Jamnut (63) and the 3/8Ó x 1 1/2Ó Bolt (60). Remove the Cable T rap (66) and ...

  • Weider WESY92190 - page 23

    1" Round Inner Cap (49) 1" Round Cover Cap (3) 3/4" Round Inner Cap (34) 3/8" x 2 1/4" Eyebolt (44) 1 1/2" Square Inner Cap (33) 2" Square Inner Cap (21) 2" Square Outer Cap (51) 1" x 2Ó Inner Cap (1 1) ...

  • Weider WESY92190 - page 24

    5/16" Nylon Jamnut (91) 3/8" Flat W asher (55) 5/16" Flat W asher (56) 3/8" Nylon Locknut (57) 3/8" Nylon Jamnut (63) 3/8" Plain Nut (85) 1/4" x 2" Bolt (71) 1/4" x 2 1/2" Screw (43) 1/4" x 2" Carriage Bolt (38) 5/16" x 1 3/4" Bolt (58) 5/16" x 2 3/4" Bolt (67) 5/16&quo ...

  • Weider WESY92190 - page 25

    1" Retainer (4) 1/4" Flat W asher (90) 3/8" x 3Ó Bolt (88) 3/8" x 2 1/4" Bolt (65) 3/8" x 1 3/4" Bolt (60) 3/8" x 3 3/4" Bolt (19) 3/8" x 4 1/2" Bolt (93) #8 x 3/4" T ap Screw (7) 3/8" x 4" T ap Screw (86) 1/4" x 5/8" Screw (95) 3/8" x 2 1/2" Bolt (96) 3/8&qu ...

  • Weider WESY92190 - page 26

    Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part ListÑModel No. WESY92190 R1299A Key No. Qty . Description Key No. Qty . Description 1 1 T op Frame 2 1 High Cable 3 2 1Ó Round Cover Cap 4 4 1Ó Retainer 5 1 Stabilizer 6 4 ÒVÓ-Pulley 7 2 Plastic Bushing 8 1 Base 9 1 Low Cable 10 1 Curl Post ...

  • Weider WESY92190 - page 27

    34 34 30 30 44 33 28 30 34 28 30 34 22 71 38 17 37 13 91 33 29 36 74 73 75 45 45 21 21 3 4 4 3 15 6 57 15 48 47 9 11 58 56 53 53 18 5 51 51 14 52 8 53 1 21 21 67 56 65 50 6 63 35 55 54 2 90 43 41 42 24 10 17 72 67 27 66 35 55 66 66 35 35 55 53 69 50 6 55 21 40 53 21 21 49 77 77 49 46 46 68 43 93 55 55 63 19 19 63 63 57 63 60 63 57 60 60 96 57 67 81 ...

  • Weider WESY92190 - page 28

    Ordering Replacement Parts T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY92190) 2. The NAME o ...

メーカー Weider カテゴリー Home Gym

Weider WESY92190のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WESY92190の取扱説明書
- Weiderの製品カード
- パンフレット
- またはWeider WESY92190の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Weider WESY92190の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Weider WESY92190の取り付け説明書、サービスマニュアル、簡易説明書、またはWeider WESY92190のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Weider WESY92190の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Weider WESY92190デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWeider WESY92190を使用するのを助ける技術的文書のことです。説明書は通常、全てのWeider WESY92190ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Weiderの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Weider WESY92190の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWeider WESY92190の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Weider WESY92190に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Weider WESY92190デバイスの基本機能を使うにあたってのヒント。 Weider WESY92190のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Weider WESY92190に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWeider WESY92190のメーカー/サービスへの連絡先に関する情報。

Weider WESY92190についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWeider WESY92190の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWeider WESY92190で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)