-
Kenmore 625.3847 - page 1
OWNER'S MANUAL MODEL NO. 625.384700 Caution: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product. If you have questions when installing, operating or maintaining your reverse osmosis system, call this toll-free number... 1-800-426-9345 SAVE THIS MANUAL PRINTED IN U.S.A. Reverse Osmosis Drinking Water Sy ...
-
Kenmore 625.3847 - page 2
- WARRANTY- 1 li I I /liJ I Ill li I I _ I Ill I / I lill_ I FULL WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM = = (except filter cartridges and R. O. membrane) = I For one year from the date of purchase, when the Reverse Osmosis Drinking Water System is installed I and maintained in accordance with our instructions, Sears will repair, free of ...
-
Kenmore 625.3847 - page 3
- TABLE OF CONTENTS - Where To Install the RO System ........ 4 Tools and Materials Needed ........... 4 Installation Steps .................... 5- 9 Cold Water Supply .................. 5 Drain Adapter ..................... 6 Faucet ............................ 6- 7 RO Assembly ...................... 7 Storage Tank, Tubing Connections .... 8 Insta ...
-
Kenmore 625.3847 - page 4
- WHERE TO INSTALL THE RO SYSTEM - The RO assembly and storage tank is designed for installation under the sink, usually in the kitchen or bathroom. The RO assembly mounts on a wall sur- face, or can lay on the cabinet floor next to the storage tank. Hanger washers and wood screws are included for cabinet wall mounting. The RO product water faucet ...
-
Kenmore 625.3847 - page 5
- STEP 1: INSTALL COLD WATER SUPPLY FITTING - Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak- tight connection to the RO 1/4" tubing (see FIG. 8, page 8). A typical connection using the included water supply fitting is shown in FIG.3 - A below. An optiona ...
-
Kenmore 625.3847 - page 6
- STEP 2: INSTALL DRAIN ADAPTER - • Note: Running the drain tubing directly to a floor drain, sump, standpipe, laundry tub, etc., as shown on page 18, is preferred. However, if that is not pos- sible or practical, the included drain adapter installs in the sink drain pipe, always above or ahead of the p-trap (FIG. 4). Be sure to comply with your ...
-
Kenmore 625.3847 - page 7
- STEP 3: INSTALL FAUCET (cont.)- B. ASSEMBLE FAUCET 1. If not already assembled, install the rubber washer, spacer, flat (or lock) washer and hex nut onto the threaded faucet stud. 2. Apply Teflon tape to the end of the faucet stud. Turn the tubing adapter with a blue collet onto the stud and hand tighten, then wrench 1/4 turn only. BE CAREFUL NOT ...
-
Kenmore 625.3847 - page 8
- STEP 5: INSTALL STORAGE TANK, MAKE REMAINING TUBING CONNECTIONS - 1. CONNECT DRAIN TUBING, FAUCET TO DRAIN ADAPTER: Referring to FIG. 8, run the loose section (connected to faucet barb fitting) of black 3 / 8" tubing from the faucet to the drain adapter, with a black collet, installed on page 6. Cut this tubing as needed to route in as strai ...
-
Kenmore 625.3847 - page 9
- STEP 6: SANITIZING, PRESSURE TESTING & PURGING - SANITIZING Sanitizing is recommended upon installation of the RO system, and after servicing inner parts. It is im- portant for the service person to have clean hands while handling inner parts of the system. CAUTION: Be sure to remove the RO membrane and both filter cartridges as follows, befo ...
-
Kenmore 625.3847 - page 10
- HOW YOUR REVERSE OSMOSIS SYSTEM WORKS - PREFILTER Water from the cold supply pipe enters the RO as- sembly prefilter first (FIG. 8 and schematic below). The prefilter has a replaceable sediment cartridge with activated carbon in its composition. The car- tridge (10 micron) removes sand, silt, dirt, other sedi- ments, and up to the ppm of chlorine ...
-
Kenmore 625.3847 - page 11
- CARE OF YOUR REVERSE OSMOSIS SYSTEM - To keep your reverse osmosis system operating and producing high quality water, you must make sure supply water is always within the limits shown in the specifications. Good supply water helps to assure longer life from the RO membrane cartridge, prefilter and postfilter cartridges. However, each of these wil ...
-
Kenmore 625.3847 - page 12
- CARE OF YOUR REVERSE OSMOSIS SYSTEM - 2. Press inward while turning the RO cap to the left (_) to remove from the bracket/membrane housing. 3. Use a pliers, or heavy wire made into a hook, to pull the RO cartridge from the housing. Note: Sanitizing is recommended after servicing in- ner parts of the system (see page 9). 4. Install the new cartrid ...
-
Kenmore 625.3847 - page 13
- CARE OF YOUR REVERSE OSMOSIS SYSTEM - TUBING CONNECTION (continued) If tubing other than tubing supplied with the system is used, be sure it is of high quality, exact size and roundness with a smooth surface. AUTOMATIC SHUTOFF SERVICE If the shutoff assembly requires service, be sure to reassemble parts exactly as shown in FIG. 12, and to reconne ...
-
Kenmore 625.3847 - page 14
- CARE OF YOUR REVERSE OSMOSIS SYSTEM - REVERSE OSMOSIS SYSTEM CARE GUIDE MODEL NO. 625.384700 1. AT LEAST every 6 months, replace the prefilter and postfilter cartridges. Clean or replace the flow control and screen. 2. Replace the RO membrane cartridge when the percent rejection of total dissolved solids (TDS) is less than shown in the specificat ...
-
Kenmore 625.3847 - page 15
- DIMENSIONS and SPECIFICATIONS - 15" Supply water pressure limits ........................ 40 - 125 psi Supply water temperature limits ..................... 40 - 100 °F Maximum total dissolved solids (TDS) ............... 2000 ppm Maximum water hardness @ 6.9 pH ................. 10 gpg Maximum iron, manganese, hydrogen sulfide ......... 0 ...
-
Kenmore 625.3847 - page 16
- REPAIR PARTS - Kenmore Reverse Osmosis Drinking Water System, Model No, 625.384700 33 !DRA , t ADAPTER 34 ! Bracket!Membrane Housing PUSH - IN FITrlNGS ] CO et 24 I 26 1/4" Tubing _ U 35 _10_ _ o-ring seals j3 I" I I 21 20 19 1 I I I I I .I 5 -9 13 12 10 23 16 ...
-
Kenmore 625.3847 - page 17
Key NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 - REPAIR PARTS - Kenmore Reverse Osmosis Drinking Water System, Part Number 7205350 7207920 7185788 42-34702 7177175 7174965 7207881 7156535 7170246 42-34370 7156577 7171674 7171682 7112442 7112434 7014979 7099296 7112426 7030721 7133838 7208502 7207899 42-34373 7 ...
-
Kenmore 625.3847 - page 18
- REMOTE LOCATION FOR REVERSE OSMOSIS SYSTEM - REMOTE RO INSTALLATION (storage tank not shown) Possible remote locations for the RO nearby the kitchen or bathroom sink include; (1) a basement area underneath the sink, and (2) an adjacent room or closet. Longer lengths of tubing may be needed (see parts list on page 17). You can run the drain tubing ...
-
Kenmore 625.3847 - page 19
19 ...
-
Kenmore 625.3847 - page 20
OWNER'S MANUAL MODEL NO. 625,384700 The model number of your reverse osmosis system is found on the rating decal. This decal is on the top of the bracket. When requesting service or ordering parts, always provide the following in- formation: • Product Type • Model Number Part Number Part Description Reverse Osmosis Drinking Water System Fo ...
Kenmore 625.3847についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもKenmore 625.3847の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKenmore 625.3847で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。