Watlow Electric 2000の取扱説明書

40ページ 0.74 mb
ダウンロード

ページに移動 of 40

Summary
  • Watlow Electric 2000 - page 1

    M INI C HEF TM 2000 Applications 7, 8 & 9 Convection Oven Applications Guide W atlow Controls 1241 Bundy Blvd. P .O. Box 5580 Winona, Minnesota U.S.A. 55987-5580 (507) 454-5300, Fax (507) 452-4507 WMC2-XAGN-0002-Rev A May 1997 $5.00 Made in the U.S.A. Programming & Operating Steps 97 Registered Company Winona, Minnesota USA ISO 9001 TOTAL C ...

  • Watlow Electric 2000 - page 2

    T able of Contents Application 7 Automatic Convection Oven . . . . . . . . . . . . . . . . 1 Application 8 Automatic Convection Oven . . . . . . . . . . . . . . . 11 Application 9 Manual Convection Oven . . . . . . . . . . . . . . . . 21 Ordering Information . . . . . . . . . . . . . . . . . . . 33 © The W atlow M INI C HEF ™ 2000 Convection Ove ...

  • Watlow Electric 2000 - page 3

    Application 7 Automatic Convection Oven One Heat Channel, Six Menus Introduction to Application 7 . . . . . . . . . . . . . . . 1 Configuration Mode Quick Reference . . . . . . . . . 3 Program Mode Quick Reference . . . . . . . . . . . . 4 Step 7 Design a Faceplate Overlay . . . . . . . . . . . 5 Step 8 Operate the Controller . . . . . . . . . . . ...

  • Watlow Electric 2000 - page 4

    Key Functions in Configuration Mode Key Functions in Operation Mode Summar y of Input/Output Functions Note: For details, see wiring instructions in the Hardware & Software Setup Guide. → Output 1 Heat → Output 2 not used → Event Output 1 Fan Low → Event Output 2 Fan High → Output 5 Audible Alarm Heat Menu 1 Menu 4 Menu 3 Menu 6 1 Men ...

  • Watlow Electric 2000 - page 5

    Application 7 Watlow M INI C HEF 2000 ■ 3 Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. Y ou must select Application 7 to access them. For directions, see the Hardware & Software Setup Guide . The Appendix of that guide includes an explanation of all ...

  • Watlow Electric 2000 - page 6

    4 ■ Watlow M INI C HEF 2000 Application 7 Program Mode Quick Reference These are the functions, parameters and values included in the Program Mode for this application. Y ou must select Application 7 to access them. For menu programming direc- tions, see the Hardware & Software Setup Guide . The Appendix of that guide includes a detailed expl ...

  • Watlow Electric 2000 - page 7

    Application 7 Watlow M INI C HEF 2000 ■ 5 Step 7 Design a Faceplate Overlay T o complete the installation, you must apply a graphic membrane to the front panel of the controller . The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide . ...

  • Watlow Electric 2000 - page 8

    6 ■ Watlow M INI C HEF 2000 Application 7 Step 8 Operate the Controller Summar y of Key Functions in Operation Mode Key Function A Menu 1 B Menu 2 C Menu 3 D Menu 4 E Menu 5 F Menu 6 Start-up Apply power to the oven. [`idle] will appear on the display . If the Real T ime Clock Display option is installed and [setUp] / [time] is pro- grammed, the ...

  • Watlow Electric 2000 - page 9

    Application 7 Watlow M INI C HEF 2000 ■ 7 The heat output indicator light - G, just below the display- will light up whenever the controller is calling for heat. When the oven is at operating temperature (above the relative set point minus the ready band) [ready] will appear on the display and the menu key indicator light will flash rapidly . Y o ...

  • Watlow Electric 2000 - page 10

    8 ■ Watlow M INI C HEF 2000 Application 7 W ith Sound set to 0, the controller automatically switches to idle in which the con- troller does not maintain temperature and does not run time. [`idle] or time of day will appear on the display . The menu key indicator light will be off. W ith Sound set to 1, 2, or 3, [``end] will appear on the display ...

  • Watlow Electric 2000 - page 11

    Application 7 Watlow M INI C HEF 2000 ■ 9 4. Once the controller goes into idle, the menu key indicator light and the heat outputs will switch off. The controller will not regulate to any temperature. 5. T o repeat cooking, repeat steps 1 through 2 or 3. Pause a Menu While cooking, you can pause cooking time by pressing the active menu key once. ...

  • Watlow Electric 2000 - page 12

    10 ■ Watlow M INI C HEF 2000 Application 7 Errors The controller will alert you to errors if they occur . Errors are critical problems that shut down the unit. If an error occurs, an error message will appear on the display . Y ou should switch off the power and call for service. See the Appendix in the Hardware & Software Setup Guide for a T ...

  • Watlow Electric 2000 - page 13

    Application 8 Automatic Convection Oven One Heat Channel, 15 Menus Introduction to Application 8 . . . . . . . . . . . . . . 11 Configuration Mode Quick Reference . . . . . . . . 13 Program Mode Quick Reference . . . . . . . . . . . . 14 Step 7 Design a Faceplate Overlay . . . . . . . . . . 15 Step 8 Operate the Controller . . . . . . . . . . . . . ...

  • Watlow Electric 2000 - page 14

    12 ■ Watlow M INI C HEF 2000 Application 8 Key Functions in Configuration Mode Key Functions in Operation Mode Summar y of Input/Output Functions Note: For details, see wiring instructions in the Hardware & Software Setup Guide. Heat 1 2 4 5 Start / Stop 6 Down Your Company Logo 3 Up Input 1 Oven T emperature → Input 2 not used → Event In ...

  • Watlow Electric 2000 - page 15

    Application 8 Watlow M INI C HEF 2000 ■ 13 Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. Y ou must select Application 8 to access them. For directions, see the Hardware & Software Setup Guide . The Appendix of that guide includes an explanation of all ...

  • Watlow Electric 2000 - page 16

    14 ■ Watlow M INI C HEF 2000 Application 8 Program Mode Quick Reference These are the functions, parameters and values included in the Program Mode for this application. Y ou must select Application 8 to access them. For menu programming direc- tions, see the Hardware & Software Setup Guide . The Appendix of that guide includes a detailed exp ...

  • Watlow Electric 2000 - page 17

    Application 8 Watlow M INI C HEF 2000 ■ 15 Step 7 Design a Faceplate Overlay T o complete the installation, you must apply a graphic membrane to the front panel of the controller . The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide ...

  • Watlow Electric 2000 - page 18

    16 ■ Watlow M INI C HEF 2000 Application 8 Step 8 Operate the Controller Summar y of Key Functions in Operation Mode Key Function A Not Used B Not Used C Menu Increment D Menu Select E Start/Stop F Menu Decrement Start-up Apply power to the oven. [`idle] will appear on the display . If the Real T ime Clock Display option is installed and [setUp] ...

  • Watlow Electric 2000 - page 19

    Application 8 Watlow M INI C HEF 2000 ■ 17 • Activate the menu by pressing the Start/Stop key . • If the oven is not at operating temperature, it will preheat. Meanwhile: The word [pre-`] [`Heat] will appear on the display for a few moments. The Start/Stop key indicator light will flash slowly . The temperature of Channel 1 will be displayed ...

  • Watlow Electric 2000 - page 20

    18 ■ Watlow M INI C HEF 2000 Application 8 W ith Sound set to 0, the controller automatically switches to idle in which the con- troller does not maintain temperature and does not run time. [`idle] or current time will appear on the display . The Start/Stop key indicator light will be off. W ith Sound set to 1, 2, or 3, [``end] will appear on the ...

  • Watlow Electric 2000 - page 21

    Application 8 Watlow M INI C HEF 2000 ■ 19 W ith Sound set to 4 or 5, [``end] will appear on the display and the Start/Stop key indicator light will flash rapidly . Y ou must acknowledge the audible signal by pressing the Start/Stop key . Once acknowledged the audible signal is silenced and the controller goes into idle. The Start/Stop key indica ...

  • Watlow Electric 2000 - page 22

    20 ■ Watlow M INI C HEF 2000 Application 8 T emperature Alarms The controller will alert you to temperature alarm conditions if they occur . If an alarm occurs, take action as determined by your supervisor . See the Appendix in the Hardware & Software Setup Guide for a T roubleshooting Chart and a summary of temperature alarms. Errors The con ...

  • Watlow Electric 2000 - page 23

    Application 9 Watlow M INI C HEF 2000 ■ 21 Application 9 Manual Convection Oven One Heat Channel Introduction to Application 9 . . . . . . . . . . . . . . 21 Configuration Mode Quick Reference . . . . . . . . 23 Step 7 Design a Faceplate Overlay . . . . . . . . . . 25 Step 8 Operate the Controller . . . . . . . . . . . . . 26 Application 9 allows ...

  • Watlow Electric 2000 - page 24

    22 ■ Watlow M INI C HEF 2000 Application 9 Key Functions in Configuration Mode Key functions in Operation Mode Summar y of Input/Output Functions Note: For details, see wiring instructions in the Hardware & Software Setup Guide . Heat 1 Temp 2 Time 4 Fan 5 Start / Stop 6 Down Your Company Logo 3 Up Input 1 Oven T emperature → Input 2 not us ...

  • Watlow Electric 2000 - page 25

    Application 9 Watlow M INI C HEF 2000 ■ 23 Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. Y ou must select Application 9 to access them. For directions, see the Hardware & Software Setup Guide . The Appendix of that guide includes an explanation of all ...

  • Watlow Electric 2000 - page 26

    24 ■ Watlow M INI C HEF 2000 Application 9 Auto-tuning Note: Before auto-tuning Application 9, [teNp1] in the operations menu must first be set to a value that is typical of your application. (See Hardware & Software Setup Guide for information.) Then set [tHerl] / [tunE1] to [```on] . After you accept [```on] , by pressing “Enter ,” the ...

  • Watlow Electric 2000 - page 27

    Application 9 Watlow M INI C HEF 2000 ■ 25 Step 7 Design a Faceplate Overlay T o complete the installation, you must apply a graphic membrane to the front panel of the controller . The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide ...

  • Watlow Electric 2000 - page 28

    26 ■ Watlow M INI C HEF 2000 Application 9 Step 8 Operate the Controller Summar y of Key Functions in Operation Mode Key Function A Cook T emp(s) B Cook T ime(s) C Up (Increment) D Fan Settings E Start/Stop F Down (Decrement) Start-up Apply power to the oven. [`idle] will appear on the display . If the Real T ime Clock option is installed and [se ...

  • Watlow Electric 2000 - page 29

    Application 9 Watlow M INI C HEF 2000 ■ 27 Set the Fan 1. Press the Fan Settings key . [`FAn1] and then the fan setting value will appear on the display . 2. Press the Up or Down key until the value you want appears on the display . 3. Press the Fan Settings key again. The Fan value has been set. [`idle] will appear on the display . The menu you ...

  • Watlow Electric 2000 - page 30

    28 ■ Watlow M INI C HEF 2000 Application 9 Set the Fan 1. Press the Fan Settings key . [~FAn1] and then the first fan setting value will appear on the display . 2. Press the Up or Down key until the value you want appears on the display . 3. Press the Fan Settings key again. The first fan value has been set. [~FAn2] and then the second fan settin ...

  • Watlow Electric 2000 - page 31

    Application 9 Watlow M INI C HEF 2000 ■ 29 2. W ith [`idle] or time of day on the display , press the Start/Stop key . If the preheat condition has not been met, the oven will preheat until [ready] appears on the display . Note: Y ou can skip preheat and go directly to the cooking sequence by pressing the Start/Stop key a second time. If the oven ...

  • Watlow Electric 2000 - page 32

    30 ■ Watlow M INI C HEF 2000 Application 9 4. When the cooking sequence is finished, [``end] will appear on the display and an audible tone will sound for two seconds. The controller will then go into idle. 5. Once the controller goes into idle, the Start/Stop indicator light will switch off. 6. T o repeat cooking, repeat steps 1 through 4. View ...

  • Watlow Electric 2000 - page 33

    Application 9 Watlow M INI C HEF 2000 ■ 31 Event Outputs While running a menu when the Configuration Mode [EtYPE] / [FAn``] is set to [````2] : When Low fan speed is on, Event Output 1 is on. When High fan speed is on, Event Output 2 is on. While running a menu when the Configuration Mode [EtYPE] / [FAn``] is set to [````1] :When the fan is on, E ...

  • Watlow Electric 2000 - page 34

    32 ■ Watlow M INI C HEF 2000 Specifications Audible Output Options • Switched dc signal, 4.5V to 5.25V , 30mA maximum output, minimum load resistance > 1 50 Ω , non-isolated. • Internal audible alarm, 75dB at 10 cm. Connectors • Sensor Input T erminal Strip 4 : RIACON, 6-position, quick-connect. • Power Supply & Input / Output T ...

  • Watlow Electric 2000 - page 35

    Ordering Information Watlow M INI C HEF 2000 ■ 33 Ordering Information (1033) F 2 H A - _ _ _ 1 - _ _ A A M INI C HEF 2000™ Cooking controller with numerous food equipment application software sets, single and dual channel on/off or PID temperature regulation, timer and machine-function control, microprocessor- based, programmable, auto-tuning, ...

  • Watlow Electric 2000 - page 36

    34 ■ Watlow M INI C HEF 2000 Ordering Information M INI C HEF 2000 Accessories 0836-0442-0000 Sensor Input Mating Connector , (RIACON #31007106), 6-position, quick-connect terminal, screw connection for 28-14 AWG wires, tighten to 7 in/lb A001-0298-0000 Power Supply and I / O Mating Connector Kit. Includes: – 1 AMP #1-640523-0, 15-position, qui ...

  • Watlow Electric 2000 - page 37

    Warranty and Returns Watlow M INI C HEF 2000 ■ 35 W atlow Controls W atlow Controls is a division of W atlow Electric Mfg. Co., St. Louis, Missouri, a manu- facturer of industrial electric heating products since 1922. W atlow begins with a full set of specifications and completes an industrial product that is manufactured totally in- house, in th ...

  • Watlow Electric 2000 - page 38

    36 ■ Watlow M INI C HEF 2000 Application 8 Notes ...

  • Watlow Electric 2000 - page 39

    Application 8 Watlow M INI C HEF 2000 ■ 37 Notes ...

  • Watlow Electric 2000 - page 40

    W atlow M INI C HEF ™ 2000 Convection Oven Applications Guide W atlow Controls, 1241 Bundy Blvd., P .O. Box 5580, Winona, MN U.S.A. 55987-5580 Phone: (507) 454-5300, Fax: (507) 452-4507 ...

メーカー Watlow Electric カテゴリー Convection Oven

Watlow Electric 2000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2000の取扱説明書
- Watlow Electricの製品カード
- パンフレット
- またはWatlow Electric 2000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Watlow Electric 2000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Watlow Electric 2000の取り付け説明書、サービスマニュアル、簡易説明書、またはWatlow Electric 2000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Watlow Electric 2000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Watlow Electric 2000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWatlow Electric 2000を使用するのを助ける技術的文書のことです。説明書は通常、全てのWatlow Electric 2000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Watlow Electricの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Watlow Electric 2000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWatlow Electric 2000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Watlow Electric 2000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Watlow Electric 2000デバイスの基本機能を使うにあたってのヒント。 Watlow Electric 2000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Watlow Electric 2000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWatlow Electric 2000のメーカー/サービスへの連絡先に関する情報。

Watlow Electric 2000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWatlow Electric 2000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWatlow Electric 2000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)