Scotsman SCN60の取扱説明書

37ページ 1.01 mb
ダウンロード

ページに移動 of 37

Summary
  • Scotsman SCN60 - page 1

    Introduction This manual includes information for the installation, operation and maintenance of the SCN60 residential ice machine. The SCN60 was developed to offer fans of Scotsman’s Nugget Ice form the ability to have that ice in their homes. Previously Nugget Ice was only available in commercial establishments, where it developed a strong foll ...

  • Scotsman SCN60 - page 2

    Product Description: This ice machine is designed to be used indoors, in a controlled environment or outdoors within certain limits. The SCN60 is made up of two major systems: the ice making system and the ice storage system. The ice making system is a continuous flow type ice machine, it makes ice when the ice level becomes low and stops when it i ...

  • Scotsman SCN60 - page 3

    Cabinet Dimensions May 2011 Page 3 SCN60 Installation and Use Scotsman Ice Systems are designed and manufactured with the highest regard for safety and performance. They meet or exceed the standards of agencies like ETL. Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that have been altered in any w ...

  • Scotsman SCN60 - page 4

    Location Recommendations: The machine can be built into a cabinet. It is an air cooled refrigeration system and so air flows in and out of it through the grill at the bottom front. The grill must not be blocked by any covering door or other obstruction. There are two models, one is a gravity drain type and it must have a building drain connection b ...

  • Scotsman SCN60 - page 5

    Familiarization The control panel is visible when the door is opened. It has three indicator lights and two switches. The model and serial number plate is located on the bottom of the control panel box. The Bin Light and Ice Level Sensor are also visible from that angle, as is the Ice Chute. The Scoop Holder is located on the right side of the ice ...

  • Scotsman SCN60 - page 6

    Decorating Features: The machine ships unfinished, allowing the attachment of a decorator door panel or a metal panel from Scotsman. Door Panel The ice machine is supplied without a conventional door covering so it can be decorated to the user ’s preference. Scotsman offers several coverings including white, black and stainless steel. In addition ...

  • Scotsman SCN60 - page 7

    Door Panel Attachment May 2011 Page 7 SCN60 Installation and Use Gasket Scotsman Door Panel Cover Machine Screw Use Upper Hole at the Top Use Lower Hole at the Bottom Hole Plug ...

  • Scotsman SCN60 - page 8

    Door Swing The door swing is reversible. The door can be attached to open with hinges on the left or right using new hinge brackets shipped loose in the ice bin. Retain all screws for re-use. To change: 1. Remove hinge cover and innermost screw holding each hinge to cabinet, loosen the other. 2. Slide hinges to the side and remove door from cabinet ...

  • Scotsman SCN60 - page 9

    Plumbing - Pump Model Drains There are two types of ice machine models, one that drains by gravity and one that has an internal drain pump. Drain Pump Model drain installation 1. Locate the coil of 3/8” ID plastic drain tubing secured to the back of the unit. 2. Route the plastic drain tube from the back of the unit to the drain connection point. ...

  • Scotsman SCN60 - page 10

    Plumbing: Gravity Drain Model Caution: Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing must be vented, have no kinks and slope to the building drain. Air gaps are typically required by local code. 1. Place the ice machine in front of the installation opening ...

  • Scotsman SCN60 - page 11

    Electrical and Start Up The ice machine is supplied with a power cord. Do not remove the grounding pin from the cord ’s plug. Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. 1. If the electrical outlet for the ice maker is behind the unit, plug in the unit. 2. Position the unit in the install ...

  • Scotsman SCN60 - page 12

    Use No special instructions are needed for use. Just take as much ice as you need, the machine will replace it. A scoop is provided, and it can be stored in the machine using the loop of tubing on the right side as a holder. The machine can be shut off anytime by just pushing and releasing the On/Off button. What shouldn’t be done? Never keep any ...

  • Scotsman SCN60 - page 13

    Maintenance Scotsman strongly recommends regular maintenance of this ice machine. During normal operation mineral scale that is in the water supply will gradually build up on the ice making surfaces. That build up can cause excessive loading of the ice making system, which can cause premature failure. Regular removal of the mineral scale will lengt ...

  • Scotsman SCN60 - page 14

    How to remove scale from the ice making system. Cleaning this machine involves adding a solution of scale remover and water to the ice machine and continuing to add it as it makes ice. The scale remover must be diluted to the correct ratio. A squirt bottle will make adding the scale remover much easier when the unit is built in. If not built in, re ...

  • Scotsman SCN60 - page 15

    6. Locate blue float valve on/off lever. Move lever up about half way to shut water off. 7. Locate drain plug and pull the drain plug out to drain the reservoir and evaporator. When draining is complete, return the plug to its original position. 8. Obtain pre-mixed Scotsman Clear 1 Scale remover solution (with squirt bottle) or mix a solution of Cl ...

  • Scotsman SCN60 - page 16

    11. Press and HOLD both the Clean-Reset and On/Off buttons for 5 seconds. The Time to Clean light will blink on and off. 12. The auger motor alone will be operating for 10 minutes, after that the compressor will start and in about 5-8 minutes the machine will start to make ice. The Time to Clean light will now glow steady until the clean cycle is c ...

  • Scotsman SCN60 - page 17

    SCN60 service This section contains information for the service and repair of the SCN60 ice machine. May 2011 Page 1 SCN60 Service Service Table of Contents SCN60 service .............................................. Page 1 Components: ............................................... Page 2 Evaporator and Auger ..................................... ...

  • Scotsman SCN60 - page 18

    Components: • Refrigeration system, including air cooled condenser, compressor, capillary tube and evaporator. • Control system, including ice level sensor, water sensor, auger motor sensor, controller, control pad and transformer. • Auger drive system, including auger motor, gear reducer and auger. • Auger support system, including top bea ...

  • Scotsman SCN60 - page 19

    Evaporator and Auger May 2011 Page 3 SCN60 Service Cut Away View Stationary Half of Water Seal Rotating Half of Water Seal Heat Exchange Tube Coil Auger Ice Outlet Bearing Foam Insulation Water Inlet ...

  • Scotsman SCN60 - page 20

    Control System The control system operates the machine. The controller operates on 12 volts AC, supplied by the transformer. It uses an ultrasonic ice sensor to measure ice level. The ultrasonic system transmits sound waves into the ice storage bin and measures the return time, when the return time is longer than the preset time for bin full, the c ...

  • Scotsman SCN60 - page 21

    Water System The auger is driven at about 11 RPM by the gear reducer. The gear reducer is a sealed component and does not require lubrication, as it contains a charge of grease. The auger motor drives a set of gears that all together reduce the motor speed to the 11 RPM output speed and correspondingly increasing the torque. The output shaft of the ...

  • Scotsman SCN60 - page 22

    Storage The ice storage system is made up of a plastic lined ice storage bin, covered by an insulated top panel and an insulated swing open door with gasket. The ice storage bin is foamed in place, so the side panels are not removable. May 2011 Page 6 SCN60 Service Ice Making Check Wat e r Time to Clean Clean Reset ...

  • Scotsman SCN60 - page 23

    Performance and Technical Specs Overall: • Refrigerant: 4.5 oz R-134a • Compressor: Hermetic, 700 BTUH • Condenser: Forced draft • Fan blade: 3 blade, 6 inch • Evaporator: Stainless steel tube, copper coil jacketed • Metering device: Cap tube • Auger drive: output speed 11 RPM • Water valve: Float in reservoir • Drain pump: Magnet ...

  • Scotsman SCN60 - page 24

    Electrical Sequence Upon power being supplied, all the lights will blink once and the control system will immediately check for water in the reservoir. If there is water no further action will occur until the On/Off button is pushed. Pushing the On/Off button starts the machine. The Ice Making light will switch on. The auger motor, compressor and f ...

  • Scotsman SCN60 - page 25

    Service Diagnosis May 2011 Page 9 SCN60 Service Problem Likely Cause Probable Solution No ice No power Plug unit into power supply Unit switched off Push and release on/off button No water, water diagnostic light is on Restore water supply, check sensor. If RO water is too pure, unit cannot operate. Check float valve for restriction Check float val ...

  • Scotsman SCN60 - page 26

    Service Diagnosis August 2011 Page 10 SCN60 Service Problem Likely Cause Probable Solution No ice, continued Ice level sensor failure With power on and Ice Making light on, check connector, if secure jump the two middle pins at J2 (bin stat) on the controller together. Unit should start. If it does, replace the sensor, if not, replace the controlle ...

  • Scotsman SCN60 - page 27

    Component Diagnostics Membrane Switch Unplug and check connector pins (left side is pin 1), read about 10 ohms when activating the button, and OL when not pressing the button: Pin 2-3 On/Off Switch; 4-3 Clean Reset Switch Compressor Check temperature of compressor, if very hot, add access valves to refrigeration system and check system pressures. I ...

  • Scotsman SCN60 - page 28

    Ice Capacity The rate of ice making is relatively fixed, it depends upon the heat load and the ambient temperature the machine is operating in. As either increase the amount of ice made will decrease. The machine will work to keep the ice bin full. A full bin of ice is when the ice level is even with the top of the front of the bin. When the ice le ...

  • Scotsman SCN60 - page 29

    Removal and Replacement Component Access The machine is designed to be cleaned while built in. See the Maintenance section for more information. Most components require the machine to be removed from a built-in situation: • Fan motor – side service panel • Controller – top panel • Auger motor – top panel, back panel • Ice sensor – t ...

  • Scotsman SCN60 - page 30

    May 2011 Page 14 SCN60 Service SCN60 Gearbox Access & Removal 1. Shut off water supply 2. Remove drain plug inside bin compartment 3. Disconnect power supply or unplug unit 4. Uninstall unit and pull out as needed for top and back access. 5. Remove top panel 6. Remove back panel 7. Remove ice chute/bin wall by unscrewing 2 thumb screws and lift ...

  • Scotsman SCN60 - page 31

    15. Remove breaker & set aside 16. Pull auger from freezer by lifting straight up (be careful as auger has sharp edges!) Note: If auger does not lift freely, see Auger Removal Procedure. 17. Inspect auger flights for signs of wear 18. Inspect evaporator barrel for signs of radial scoring 19. Remove 4 screws securing gearbox bracket to compartme ...

  • Scotsman SCN60 - page 32

    Water Seal Replacement 1 Go through the prior steps to remove the gear reducer. 2 Remove rotating half of water seal from bottom of auger. 3 Clean auger of any sealant at water seal mounting position. 4 Add a small bead of food grade silicone sealant to the shoulder of the auger where the water seal will go. Note: Do NOT touch the mating surfaces o ...

  • Scotsman SCN60 - page 33

    13 Slide breaker onto auger shaft. Secure with the original four allen head bolts. 14 Reverse the balance of the steps to complete putting the machine back together. Gear Reducer Replacement 1 The gear reducer contains no internal serviceable parts. Replace as a unit. 2 Follow all steps to remove gear reducer from evaporator. 3 Remove bolts holding ...

  • Scotsman SCN60 - page 34

    Evaporator Replacement 1 Go through all steps to remove the gear reducer. 2 Add temporary refrigeration system access valves to the discharge and suction sides of the refrigeration system . 3 Recover the refrigerant. 4 Un-sweat the suction line and cap tube connections from the evaporator. 5 Remove original dryer. 6 Attach permanent access valves t ...

  • Scotsman SCN60 - page 35

    Drain Pump (if equipped) 1 Shut off water supply 2 Remove all ice and/or any standing water. 3 Disconnect power or unplug unit 4 Uninstall and pull unit out to get access to left side service panel. 5 Remove five screws and the service panel. 6 Disconnect electrical plug to pump motor 7 Disconnect drain hose from pump inlet 8 Disconnect discharge h ...

  • Scotsman SCN60 - page 36

    Compressor replacement. 1 Shut off water supply 2 Disconnect power supply or unplug unit 3 Uninstall unit and pull out as needed for side and back access. 4 Remove back panel including drain and power supply panels. 5 Remove side service panel. 6 Go through all steps to remove drain pump and/or fan motor. 7 Remove drain hose from unit. 8 Add tempor ...

  • Scotsman SCN60 - page 37

    Bin and Cabinet The bin and cabinet can be separated from the base. Either the ice making evaporator system must be lifted out and securely suspended or the refrigeration system opened and the connections to the evaporator unbrazed . 1 Remove the unit from its installed position. 2 Disconnect water supply. 3 Disconnect / unplug unit from power supp ...

メーカー Scotsman カテゴリー Ice Maker

Scotsman SCN60のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SCN60の取扱説明書
- Scotsmanの製品カード
- パンフレット
- またはScotsman SCN60の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Scotsman SCN60の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Scotsman SCN60の取り付け説明書、サービスマニュアル、簡易説明書、またはScotsman SCN60のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Scotsman SCN60の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Scotsman SCN60デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがScotsman SCN60を使用するのを助ける技術的文書のことです。説明書は通常、全てのScotsman SCN60ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Scotsmanの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Scotsman SCN60の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははScotsman SCN60の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Scotsman SCN60に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Scotsman SCN60デバイスの基本機能を使うにあたってのヒント。 Scotsman SCN60のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Scotsman SCN60に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるScotsman SCN60のメーカー/サービスへの連絡先に関する情報。

Scotsman SCN60についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもScotsman SCN60の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがScotsman SCN60で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)