Snapper GM2515KAWの取扱説明書

24ページ 2.35 mb
ダウンロード

ページに移動 of 24

Summary
  • Snapper GM2515KAW - page 1

    OPERA T OR’S MANU AL SIMPLICITY Mfg. No. Description 1694240 13HP Honda Walk-Behind Brush Mower 1694204 13HP Briggs Walk-Behind Brush Mower 1694205 13HP Kawasaki Walk-Behind Brush Mower FERRIS Mfg. No. Description 1694249 13HP Briggs Walk-Behind Brush Mower (BC25BE) 1694251 13HP Honda Walk-Behind Brush Mower (BC25H) GIANT-VAC Mfg. No. Description ...

  • Snapper GM2515KAW - page 2

    1 T roub leshooting, Adjustment and Service .....14 Chart .....................................................................14 Travel Control Adjustment ....................................16 Blade Clutch Adjustment .......................................17 Blade Brake Adjustment .......................................18 Mower Belt Adjustment .. ...

  • Snapper GM2515KAW - page 3

    2 SAFE OPERA TION PRA CTICES FOR W ALK-BEHIND MO WERS This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the follow- ing safety instructions could result in serious injury or death. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual(s). Be thorough ...

  • Snapper GM2515KAW - page 4

    3 Safety Rules and Information SLOPE OPERA TION Slopes are a major factor related to slip and fall acci- dents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it. Do • Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. • Re ...

  • Snapper GM2515KAW - page 5

    4 Safety Rules & Information SER VICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refu- eling. Do not smoke. c) Never refuel the unit indoors. • I ...

  • Snapper GM2515KAW - page 6

    5 Safety and Instructional Decals Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All mowers Decal - Blade Control, Engine Key Switch (7028349) Models - All mowers Decal - Traction Drive / Freewheel Lever (1725229) Models - All mowers ...

  • Snapper GM2515KAW - page 7

    6 Features & Controls Engine On/Starter Rotate this key switch to the ON position before pulling on the starter rope. If the mower is equipped with the optional electric start- ing system, rotate the key past the ON position to engage the starter. When the engine starts, release the key. Throttle Contr ol The throttle controls engine speed. Mov ...

  • Snapper GM2515KAW - page 8

    7 Operating the Mower Engage Disengage Figure 4 - Traction Drive / Freewheel Control ST AR TING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions. In order to obtain optimum performance from your engine, refer to y ...

  • Snapper GM2515KAW - page 9

    8 Operating the Mower T o Pr opel Unit Forward: • Grasping both upper handle/safety bar (A, Figure 5) and lower portion of traction drive engagement bar (B) with both hands, slowly begin squeezing engage- ment bar up toward handle. The unit should begin moving forward. T o Pr opel Unit In Reverse: • Grasping both upper handle/safety bar (A, Fig ...

  • Snapper GM2515KAW - page 10

    9 Operating the Mower OFF RUN ST ART A Figure 7 - PTO Engaged A. Blade Engagement Lever in engaged position. OFF RUN ST ART A Figure 8 - PTO Disengaged A. Blade Engagement Lever in the disengaged posi- tion. ENGA GING/DISENGA GING THE CUTTING BLADE To Engage Cutting Blade: • Push Blade Engagement Lever forward and then to the right until lever lo ...

  • Snapper GM2515KAW - page 11

    10 Operating the Mower A D C C B Figure 9 - Adjusting Height A. Skid B. Capscrew C. Washer D. Nut T O ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for height adjustment: – Top holes - 3 1 / 4 " cutting depth – Center holes - 4" cutting depth – Bottom holes - 4 3 / 4 " cutting depth ? ...

  • Snapper GM2515KAW - page 12

    11 Regular Maintenance LUBRICA TION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surfaces clean before and after lubrication. Grease: ...

  • Snapper GM2515KAW - page 13

    12 Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). B A TTER Y SER VICE Cleaning the Battery and Cables - 9HP Models Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (C, Figure 13a). 2. Remove the battery hold-down (B), rubber protective sheet (D) and battery (A). 3. Clean the bat ...

  • Snapper GM2515KAW - page 14

    13 Regular Maintenance SER VICING THE MO WER BLADES Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. 2. Blades should be sharp and free of nicks and dents. If worn or damaged, replace the blades as described in following steps. 3. To remove the blade, use a wood ...

  • Snapper GM2515KAW - page 15

    14 T roubleshooting, Adjustment, & Service TR OUBLESHOO TING PROBLEM CAUSE REMEDY Engine will not turnover or start. 1. PTO lever in the engaged position. Place in disengaged position. 2. Out of fuel. If the engine is hot, allow it to cool, then refill the fuel tank. 3. Engine flooded. Disengage choke. 4. Battery terminals require cleaning. See ...

  • Snapper GM2515KAW - page 16

    15 T roubleshooting, Adjustment & Service T r oubleshooting Cont. Blade will not engage. 1. Blade clutch rod too loose. See Blade Clutch Adjustment Section. 2. Blade belt worn or broken. Turn off engine and inspect belt. Adjust or replace as required. 3. Over-stretched or broken spring Turn off engine and inspect spring. Replace on blade clutch ...

  • Snapper GM2515KAW - page 17

    16 T roubleshooting, Adjustment, & Service TRA VEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2. Loosen the wing nut locknut (D) and rotate control rod (C) until engagement bars are properly adju ...

  • Snapper GM2515KAW - page 18

    17 T roubleshooting, Adjustment, & Service A D C B E Figure 17 - Blade Clutch Adjustment A. Clutch Rod B. Clutch Rod Lever C. Clutch Rod Fitting D. Locknut E. Hairpin Clip BLADE CLUTCH ADJUSTMENT If the mower blade does not stop running when the blade clutch lever is in the DISENGAGED position, does not run at full speed, adjust the Blade Clutc ...

  • Snapper GM2515KAW - page 19

    18 T roubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT The mower blade should stop within 5 seconds after the Blade Engagement Lever is moved to the DISEN- GAGED position. This adjustment is checked by: 1. Remove blade clutch cover plate (A, Figure 19). 2. Start engine. 3. With mower blade engagement lever in the DISEN- GAGED positio ...

  • Snapper GM2515KAW - page 20

    19 T roubleshooting, Adjustment, & Service A D B 1/8” Max. C Figure 21 - Traction Drive Belt Adjustment A. Transmission Pulley B. Drive Belt C. Engine Pulley D. Idler Pulley Figure 22 - Traction Drive Belt Adjustment A. Adjustment Nut TRA CTION DRIVE BEL T ADJUSTMENT If the mower drive is not functioning properly, the drive belt may need to b ...

  • Snapper GM2515KAW - page 21

    20 T roubleshooting, Adjustment & Service E D G F B C A Figure 24 - Belt Alignment A. Blade Drive Pulley B. Mower Belt C. Mower Tension Idler D. Transmission Pulley E. Transmission Belt F. Engine Pulley G. Transmission Tension Idler MO WER BEL T REPLA CEMENT To replace the mower blade drive belt; NOTE - The traction drive belt will have to be r ...

  • Snapper GM2515KAW - page 22

    21 Specifications Parts & Accessories ENGINEl BRIGGS HONDA KAWASAKI BRIGGS Engine 13 HP B&S 13 HP Honda 15 HP V-twin 16 HP B&S Transmission Hydro/Variable Hydro/Variable Hydro/Variable Hydro/Variable Ground Speed (mph) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Weight (lbs) 287 298 299 N/A Overall Length ...

  • Snapper GM2515KAW - page 23

    22 Notes ...

  • Snapper GM2515KAW - page 24

    Products, Inc. 535 Macon Street/PO Box 777 McDonough, GA 30253 © Copyright 2003 Snapper Products, Inc. All Rights Reserved. Printed in USA. ...

メーカー Snapper カテゴリー Lawn Mower

Snapper GM2515KAWのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GM2515KAWの取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper GM2515KAWの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper GM2515KAWの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper GM2515KAWの取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper GM2515KAWのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper GM2515KAWの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper GM2515KAWデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper GM2515KAWを使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper GM2515KAWユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper GM2515KAWの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper GM2515KAWの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper GM2515KAWに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper GM2515KAWデバイスの基本機能を使うにあたってのヒント。 Snapper GM2515KAWのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper GM2515KAWに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper GM2515KAWのメーカー/サービスへの連絡先に関する情報。

Snapper GM2515KAWについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper GM2515KAWの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper GM2515KAWで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)