Cisco Systems MC-413の取扱説明書

22ページ 0.29 mb
ダウンロード

ページに移動 of 22

Summary
  • Cisco Systems MC-413 - page 1

    MC-413 Cisco IOS Multiservice Applic ations Configu ration Gu ide Configuring Support for PBX Signalling Protocols This chapter de scribes ho w to conf igure su pport for PBX sig nalling for mats such a s Q.SIG and transparent common channel signalli ng (CCS). Conf iguring support f or these signalling protoco ls on your router enables th e router ...

  • Cisco Systems MC-413 - page 2

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-414 Cisco IOS Multiservice Applications Configuration Gu ide – ECMA 142: Specif ication, Functional Mod e l and Informatio n Flows for Contr ol Aspects of Cir cuit Mode Basic Services in Private T elecommunication Networks . – ECMA 141: Private T eleco ...

  • Cisco Systems MC-413 - page 3

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Q.SIG PRI Signalling Su pport MC-415 Cisco IOS Multiservice Applic ations Configur ation Guide • Q.SIG data calls are not support ed. All calls with bearer capability indicat ing a nonv oice type (such as video telephon y) are rejected. • The incoming PO TS dial peer must hav e DID ...

  • Cisco Systems MC-413 - page 4

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-416 Cisco IOS Multiservice Applications Configuration Gu ide Step 2 Router(config )# controller { T1 | E1 } controller number Enters controller conf iguration mode. Step 3 Router(config-controller)# pri-group [ timeslot range ] Confi gures the PRI group fo ...

  • Cisco Systems MC-413 - page 5

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Q.SIG PRI Signalling Su pport MC-417 Cisco IOS Multiservice Applic ations Configur ation Guide As sho wn in the preceding section, you ha ve a choice of conf iguring the isdn-switch-type command to support Q.SIG at ei ther the global conf iguration lev el or the interface co nfiguration ...

  • Cisco Systems MC-413 - page 6

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-418 Cisco IOS Multiservice Applications Configuration Gu ide Figur e 97 Q.SIG Signalling Co nfiguration with NEC PBX T o conf igure NEC Fusion signalling support on the Cisco AS5300, use the followi ng commands begin ning in global conf iguration mode: Ver ...

  • Cisco Systems MC-413 - page 7

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Q.SIG PRI Signalling Su pport MC-419 Cisco IOS Multiservice Applic ations Configur ation Guide Q.SIG for VoIP Configuration Example The follo wing configu ration example conf igures interf ace serial 1:23 for Q.SIG PRI and to act as the Q.SIG slav e: ! version 12.0 service timestamps de ...

  • Cisco Systems MC-413 - page 8

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-420 Cisco IOS Multiservice Applications Configuration Gu ide shutdown ! ip default-gateway 1.14.0.1 ip classless ! line con 0 transport input none line aux 0 line vty 0 4 login ! end ===================================================== ! version 12.0 serv ...

  • Cisco Systems MC-413 - page 9

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Q.SIG PRI Signalling Su pport MC-421 Cisco IOS Multiservice Applic ations Configur ation Guide no ip directed-broadcast isdn switch-type primary-qsig isdn protocol-emulate network isdn incoming-voice modem ! interface FastEthernet0 no ip address no ip directed-broadcast shutdown ! ip de ...

  • Cisco Systems MC-413 - page 10

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-422 Cisco IOS Multiservice Applications Configuration Gu ide Figure 98 Cisco MC381 0 Q.SIG Signalling Configur ation Q.SIG Prerequisite Tasks The follo wing configu ration tasks should be co mpleted before you conf igure Q.SIG on the Cisco MC3810: • Conf ...

  • Cisco Systems MC-413 - page 11

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Q.SIG PRI Signalling Su pport MC-423 Cisco IOS Multiservice Applic ations Configur ation Guide Step 3 Router(config-if)# isdn switch-type [ primary-qsig-slave | primary-qsig-master ] If you did not conf igure the global ISDN switch type for Q.SIG support in Step 1, conf igures the inter ...

  • Cisco Systems MC-413 - page 12

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-424 Cisco IOS Multiservice Applications Configuration Gu ide As sho wn in the procedure, you ha ve a choice of conf iguring the isdn-switch-type command to support Q.SIG at either the global configurat ion le vel or at t he interface config uration lev el. ...

  • Cisco Systems MC-413 - page 13

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Q.SIG PRI Signalling Su pport MC-425 Cisco IOS Multiservice Applic ations Configur ation Guide Q.SIG PRI Signalling on the Cis co MC3810 Configuration Example The follo wing configu ration example conf igures interf ace serial 1:15 for QSIG PRI, and to act as the QSIG master . The examp ...

  • Cisco Systems MC-413 - page 14

    Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Suppor t MC-426 Cisco IOS Multiservice Applications Configuration Gu ide no logging event link-status isdn switch-type primary-qsig-master isdn bchan-number-order ascending no cdp enable ! interface Switch0 no ip address no ip directed-broadcast encapsulation frame-re ...

  • Cisco Systems MC-413 - page 15

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-427 Cisco IOS Multiservice Applic ations Configur ation Guide dial-peer voice 10 vofr destination-pattern 4... session target Serial0 30 ! end Configuring Transparent CCS on the Cisco MC3810 The Cisco MC3810 pro vides support for transparent CCS, w ...

  • Cisco Systems MC-413 - page 16

    Configuring Support for PBX Signalling Protocols Configuring Transpar ent CCS on the Cisco MC3810 MC-428 Cisco IOS Multiservice Applications Configuration Gu ide Configuring CCS Cr oss-Connect for T1 When you configure CCS cross-connect for T1, you ne ed to cross-connect f rom the first T1 controller to the second T1 controller . T o config ure CCS ...

  • Cisco Systems MC-413 - page 17

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-429 Cisco IOS Multiservice Applic ations Configur ation Guide Configuring T1/E1 Tr unk Bearer Channels If you will us e CCS cross-connect for bearer channels of the T1/E1 trunk, you will n eed to perform some additional conf iguration. T o conf igu ...

  • Cisco Systems MC-413 - page 18

    Configuring Support for PBX Signalling Protocols Configuring Transpar ent CCS on the Cisco MC3810 MC-430 Cisco IOS Multiservice Applications Configuration Gu ide The voice channel type conf igured as the ext-sig-master is considered the master side of the permanent virtual circuit (PVC) connection and is responsibl e for establishing the PVC connec ...

  • Cisco Systems MC-413 - page 19

    Configuring Suppor t fo r PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-431 Cisco IOS Multiservice Applic ations Configur ation Guide Note When CCS frame-forwarding is configured, the speed (clock rate) of serial interface 1 on the Cisco MC3810 is limited to a maximum of 192 kbps. This r e striction assumes t hat the M ...

  • Cisco Systems MC-413 - page 20

    Configuring Support for PBX Signalling Protocols Configuring Transpar ent CCS on the Cisco MC3810 MC-432 Cisco IOS Multiservice Applications Configuration Gu ide Step 4 For Cisco MC3810 series analog v oice ports: router(config)# voice-port slot/port For Cisco MC3810 series digital voice p orts: router(config)# voice-port slot:ds0-group Enters v oi ...

  • Cisco Systems MC-413 - page 21

    Configuring Suppor t fo r PBX Signalling Protocols CCS Frame-Forwarding Configur ation Example MC-433 Cisco IOS Multiservice Applic ations Configur ation Guide CCS Frame-Forwarding Configuration Example The follo wing configu ration example conf igures CCS frame-forwarding on controller E1. Other commands necessary for the co nf iguration are inclu ...

  • Cisco Systems MC-413 - page 22

    Configuring Support for PBX Signalling Protocols CCS Frame-For warding Configu ration Exampl e MC-434 Cisco IOS Multiservice Applications Configuration Gu ide interface Serial1:15 no ip address no ip directed-broadcast ccs connect Serial0 30 ! interface Switch0 no ip address no ip directed-broadcast encapsulation frame-relay no fair-queue ! interfa ...

メーカー Cisco Systems カテゴリー Network Router

Cisco Systems MC-413のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MC-413の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems MC-413の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems MC-413の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems MC-413の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems MC-413のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems MC-413の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems MC-413デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems MC-413を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems MC-413ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems MC-413の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems MC-413の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems MC-413に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems MC-413デバイスの基本機能を使うにあたってのヒント。 Cisco Systems MC-413のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems MC-413に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems MC-413のメーカー/サービスへの連絡先に関する情報。

Cisco Systems MC-413についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems MC-413の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems MC-413で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)