Heath Zenith SL-6107の取扱説明書

32ページ 0.39 mb
ダウンロード

ページに移動 of 32

Summary
  • Heath Zenith SL-6107 - page 1

    SL-6107 © 2006 DESA Specialty Products™ 595-4514-14 The Heath ® /Zenith Motion Sensing 3-W ay W all Switch automatically contr ols indoor lighting: • In A UT O mode, the control automatically tur ns the light on when you enter the room. The length of time the light stays on is adjustab le. The Heath ® /Zenith SL-6107 Motion Sensing 3-Wa y W ...

  • Heath Zenith SL-6107 - page 2

    595-4514-14 -2- Some local building codes may require installation b y a quali- fied electrician. INST ALLA TION ❐ For yo ur sa fety , turn off p owe r at the f use o r cir cui t bre aker . Note: A “3-wa y” circuit controls lights from two separate s witches. If you w ant to use this product in a single s witch circuit or if y ou want to ins ...

  • Heath Zenith SL-6107 - page 3

    -3- 595-4514-14 INST ALLA TION AUTO OFF ON AUTO OFF ON SL-6107 SWITCH 1 ST IN CIRCUIT WHITE FROM POWER SOURCE BLACK BLA CK WHITE RED (In Wall) BROWN BLACK EXISTING 3-WA Y SWITCH ADD JUMPER WIRE SL-6107 RED (From 6107) WHITE BLACK *COMMON ONE SL-6107 SWITCH IN CIRCUIT WHITE FROM POWER SOURCE BLACK WHITE BLACK WHITE BLACK *COMMON *COMMON SL-6107 SWIT ...

  • Heath Zenith SL-6107 - page 4

    595-4514-14 -4- COMMON The switch ma y indi cate t he co mmon OR Color of screw ma y be different f or the common INST ALLA TION 1. Add J umper At Remote 3-W ay Switch. A jumper wire between the common wire and one of the switched wires is used to supply power to the SL-6107 regardless of the posi- tion of the remote switch. ❐ Remove remote s wit ...

  • Heath Zenith SL-6107 - page 5

    -5- 595-4514-14 2. Replace Other Switch. ❐ T urn the power off at the cir cuit breaker . ❐ Remove and disconnect the old s witch. Note: If you can’t tell which wire is common, etc., connect the wires in the follo wing steps as best you can, then follow the test on the next page . ❐ Connect the black motion sensor wire to the common wire. ? ...

  • Heath Zenith SL-6107 - page 6

    595-4514-14 -6- INST ALLA TION T est For Correct Common Wire Connection: Re-install the switch. T urn the circuit breaker back on. Leaving the jumpered s witch in one position, flip the other 3-wa y switch on and off. Lights turn on and off. Lights turn on and off. Jumper is correct. Go to next page . Flip the switch with the jumper wire to the oth ...

  • Heath Zenith SL-6107 - page 7

    -7- 595-4514-14 ❐ Mount the SL-6107 into the junction box with the two junction box screws . ❐ T urn the circuit breaker back on. ❐ Preset the controls: Time to minutes, Photo Adjustment fully clockwise . Cov er the lens with masking tape. ❐ With the motion sensor in the “ON” position, tur n the remote switch on and off se veral times. ...

  • Heath Zenith SL-6107 - page 8

    595-4514-14 -8- F o r single switch installations, c o n - nect the wall switch as shown here. If you want to have mo- tion sensors at both 3-way switches, con- nect them as shown below . The minimum wattage ma y increase to 100 W f or fluores- cent and 50 W for in- candescent lighting. SPECIAL INST ALLA TIONS AUTO OFF O N SINGLE SWITCH INST ALLA ...

  • Heath Zenith SL-6107 - page 9

    -9- 595-4514-14 OF F N O AU TO ADJUSTMENT TIME LIGHT + Test 20 15 1 5 10 Dark Any Light Le vel 5 Seconds 20 Minutes Press in with screwdriver . Swing out cov er to remove . The sensor can be prevented from tur ning on lights when there is already enough light in the room. Use a small screwdriver to set the light lev el using this diagram as a guide ...

  • Heath Zenith SL-6107 - page 10

    595-4514-14 -10- TIME CONTROL There are 6 preset selections for the amount of time the lights stay on: T est (5 seconds), 1, 5, 10, 15, and 20 minutes. Use a small, phillips screw driver to adjust the TIME control (see Figure 4). T ur n the TIME control until it “snaps” into the desired time position. ADJUSTMENT Outlet Cover Plate N O AUTO OF F ...

  • Heath Zenith SL-6107 - page 11

    -11- 595-4514-14 USING THE LIGHT CONTROL One of three functions can be selected by using the three-position switch on the SL-6107: Off: When you want the light off all the time. The light will not be switched on by either switch. Put the control in this position when changing light bulbs. Auto: When y ou want the light to come on and turn off auto ...

  • Heath Zenith SL-6107 - page 12

    595-4514-14 -12- Light will not come on: • Circuit breaker is off . T urn breaker back on. • Bulb is burned out. Replace light bulb. • Photo Sensitivity is set to D ARK. Rotate the adjustment clockwise towards the LIGHT position. • Control is in the “Off” position. Set to Auto or On. • Control ma y be wired incorrectly . See T roubles ...

  • Heath Zenith SL-6107 - page 13

    -13- 595-4514-14 In the A uto mode, light does not sta y on: • Motion is needed to keep the light on. • Time control is adjusted for too little time. T ur n the Time control clockwise . Note: In the minimum time position, fluorescent lights may not ha ve enough time to turn on. In the A uto mode, light turns on in da ylight: • Photo adjustme ...

  • Heath Zenith SL-6107 - page 14

    595-4514-14 -14- This product is to be installed indoors only . Electrical Input ............................................................. 120V , 60 Hz. Fluorescent* Load ......................................... (2) 30 Watt minimum, Up to 400 Watts Maxim um Rapid Start Ballast Motor Load ................................................. Up to ...

  • Heath Zenith SL-6107 - page 15

    -15- 595-4514-14 FIVE YEAR LIMITED W ARRANTY Th is is a “L imi ted W ar ra nty ” wh ich gi ve s yo u sp ec ific le gal rig ht s. Y ou ma y als o ha v e o the r r igh ts whi ch v ary f rom s tat e t o s tat e o r p ro vin ce to pr ov inc e. For a period of five years from the date of purchase, any malfunction caused by factory defectiv e par t ...

  • Heath Zenith SL-6107 - page 16

    595-4514-14 -16- INTERRUPTOR TRIDIRECCIONAL DE PARED Y DECTECTOR DE MOVIMIENTO SL-6107 El Interr uptor T r idireccional de pared y Dectector de Movimiento controla automáticamente la ilumina- ción interna: • En la modalidad de A UT O, el control automática- mente prende la luz cuando usted entr a al cuar to . El período de tiempo que la luz s ...

  • Heath Zenith SL-6107 - page 17

    -17- 595-4514-14 Algunos códigos locales de construcción pueden requerir que la instalación sea hecha por un electricista calificado. INST ALACION ❐ Para su seguridad, apague la energía en el fusible o en el cortacircuitos. Nota: un circuito “tridireccional” es un circuito de luz controlado desde dos interr uptores separados. Si desea us ...

  • Heath Zenith SL-6107 - page 18

    595-4514-14 -18- INST ALACION AUTO OFF ON DISPOSICIÓN DEL INTERRUPT OR DE LA LÁMP ARA EXISTENTE BLANCO DE LA FUENTE DE ALIMENT ACIÓN NEGRO BLANCO ROJO (en la pared) NEGRO BLANCO NEGRO INTERRUPT OR SL-6107 1ro EN EL CIRCUITO BLANCO DE LA FUENTE DE ALIMENT ACIÓN NEGRO NEGRO BLANCO ROJO (en la pared) MARRÓN NEGRO INTERRUPTOR DE 3-VÍAS EXISTENTE ...

  • Heath Zenith SL-6107 - page 19

    -19- 595-4514-14 COMMON INST ALACION 1. Una el cable de conexión al interruptor tridireccional a control remoto. Se usa un cable de cone xión entre el alambre común y uno de los alambres con interruptor para suplir energía al SL-6107 cualquiera sea la posición del interruptor a control remoto. ❐ Quite el interr uptor a control remoto de la c ...

  • Heath Zenith SL-6107 - page 20

    595-4514-14 -20- Conecte el SL-6107 a la conexión existente INST ALACION 2. Instale el Detector de Movimiento en el otro inte- rruptor . ❐ Apague la energía en el cor tacircuitos. ❐ Quite y desconecte el interr uptor viejo . Nota: Si no sabe cuál es el alambre común, etc., en los pasos que siguen, conecte los alambres lo mejor que pueda y h ...

  • Heath Zenith SL-6107 - page 21

    -21- 595-4514-14 Prueba para la conexión correcta de un cable común Reinstale el interruptor. Prenda de nuev o el cortacircuitos. Dejando el cable con puente en una posición, prenda y apague el otro interruptor tridireccional. La luz se prende y se apaga. El puente está bien. V ay a a la página siguiente. Muev a el interruptor con el cable de ...

  • Heath Zenith SL-6107 - page 22

    595-4514-14 -22- INST ALACION * Apague la energia antes de reconectar! Pruebe de nue vo . V aya al 2 ó al 3. Si la luz no se prende: 1. Cambie* los alambres Rojos y Negros del Control. ➯ Si luz con el inte- rruptor a control re- moto en cualquier posición: 3. Fije el d etect or a la fa se de “AUT O”. Espe re ha sta q ue el apar ato s e cali ...

  • Heath Zenith SL-6107 - page 23

    -23- 595-4514-14 Se pueden insta- lar dos detectores de movimiento en ca da i nte rru pto r d e 3 dir ec cio ne s como se muestra abajo . El va t i a j e m í n i m o r e - querido puede subir a 100 vatios para luz fluorescente y a 50 vatios para la incan- descente. INST ALACIONES ESPECIALES Para instalaciones de un solo interrup- tor conecte el i ...

  • Heath Zenith SL-6107 - page 24

    595-4514-14 -24- SENSIBILID AD DE FO T O AJUSTE El dete ctor puede prev enir que se prenda la luz cuand o existe ya sufic iente luz en el cuarto . Use un pequeñ o desto rnill ador para fija r el nive l de luz usand o este diagra ma como g uía. Cuand o está comple - tame nte hacia la derec ha, el detecto r prende la luz aún en pleno día. Cuan ...

  • Heath Zenith SL-6107 - page 25

    -25- 595-4514-14 CONTROL DEL TIEMPO Hay 6 ajustes precalibrados para el lapso de tiempo que las luces permanecen encendidas: Prueba (5 segundos), 1, 5, 10, 15 y 20 mi- nutos . Use un destornillador Phillip s pequeño para regular el control de TIEMPO (V ea la Figura 4). Gire el control hasta que se “coloque a presión” en la posición de tiempo ...

  • Heath Zenith SL-6107 - page 26

    595-4514-14 -26- FUNCIONAMIENT O CÓMO USAR EL CONTROL DE LUZ Se pueden escoger tres posiciones cuando se usa el interruptor de tres posiciones del SL-6107: Off: Cuando quiere que la luz esté siempre apagada. La luz no se prenderá con ninguno de los dos interruptores. Coloque el control en esta posición cuando cambie bombillas. Auto: Cuando quie ...

  • Heath Zenith SL-6107 - page 27

    -27- 595-4514-14 La luz no se prende: • El cor tacircuitos está apagado . Préndalo de nue vo . • La bombilla está quemada. Cambie la bombilla. • La sensibilidad de f oto está fijada en D ARK (OBSCUR O). Gire el ajuste hacia la derecha hacia la posición de LIGHT (CLARO). • El control está en la posición de apagado (OFF). Préndalo (O ...

  • Heath Zenith SL-6107 - page 28

    595-4514-14 -28- INVESTIGA CION DE A VERIAS • Puede ser que se le hay a movido al interruptor a control remoto . La luz no se prende cuando está en automático: • Si hay demasiada luz en el cuar to, pueda ser que la luz no se prenda. Gire el control de Foto hacia la izquierda hacia la posición de LIGHT (claro). L a l uz no se q ue da p re nd ...

  • Heath Zenith SL-6107 - page 29

    -29- 595-4514-14 Este producto debe ser instalado sólo dentro de casa. Entrada eléctrica..........................................................120V , 60 Hz. Carga Fluorescente* ......................................... (2) 30 V atios Mín. y Hasta 400 V atios Máximo Estabilizador de arranque rápido Carga del motor ........................... ...

  • Heath Zenith SL-6107 - page 30

    595-4514-14 -30- GARANTÍA LIMIT AD A A 5 AÑOS Esta es una “Garantía Limitada” que le da a Ud. derechos legales específicos. Usted puede también tener otros derechos que varían de estado a estado o de provincia a provincia. P or un período de 5 años desde la fecha de compra, c ualqui er mal funcionamiento ocasionado por par tes defectuo ...

  • Heath Zenith SL-6107 - page 31

    -31- 595-4514-14 Notes / Notas _________________ _________________ _________________ _________________ _________________ _________________ _________________ _________________ _________________ ...

  • Heath Zenith SL-6107 - page 32

    595-4514-14 -32- Notes / Notas _________________ _________________ _________________ _________________ _________________ _________________ _________________ _________________ _________________ ...

メーカー Heath Zenith カテゴリー Indoor Furnishings

Heath Zenith SL-6107のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SL-6107の取扱説明書
- Heath Zenithの製品カード
- パンフレット
- またはHeath Zenith SL-6107の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Heath Zenith SL-6107の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Heath Zenith SL-6107の取り付け説明書、サービスマニュアル、簡易説明書、またはHeath Zenith SL-6107のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Heath Zenith SL-6107の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Heath Zenith SL-6107デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHeath Zenith SL-6107を使用するのを助ける技術的文書のことです。説明書は通常、全てのHeath Zenith SL-6107ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Heath Zenithの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Heath Zenith SL-6107の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHeath Zenith SL-6107の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Heath Zenith SL-6107に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Heath Zenith SL-6107デバイスの基本機能を使うにあたってのヒント。 Heath Zenith SL-6107のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Heath Zenith SL-6107に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHeath Zenith SL-6107のメーカー/サービスへの連絡先に関する情報。

Heath Zenith SL-6107についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHeath Zenith SL-6107の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHeath Zenith SL-6107で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)