-
PYLE Audio PTA3000 - page 1
PROFESSIONAL POWER AMPLIFIER OPERA TING GUIDE PT A3000 ...
-
PYLE Audio PTA3000 - page 2
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’ s enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. ...
-
PYLE Audio PTA3000 - page 3
2 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacture, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over . 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. R efer all servicing to qual ...
-
PYLE Audio PTA3000 - page 4
Thanks for choose our series amplifier . The amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology gained through years ...
-
PYLE Audio PTA3000 - page 5
(1) INPUT GAIN (dB) These controls are used to adjust the input gain of each channel. They determine how loud each channel of the power amplifier will sound for a given input signal level. Maximum input gain is achieved at the fully clockwise setting, and this setting yields maximum mixer/system headroom. A setting of less than fully clockwise will ...
-
PYLE Audio PTA3000 - page 6
( 7) IEC MAINS CONNECT OR This is a standard IEC power connector . An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. U.S. DOMESTIC AC MAINS CORD The mains cord supplied with the unit is a heavy-duty , 3-conductor type with a conventional 120 V AC plug with ground pin. It should ...
-
PYLE Audio PTA3000 - page 7
6 (9) SPEAKON OUTPUTS The amplifiers utilize three 4-conductor Speakon connectors, one for each channel and one for BRIDGE mode. Please refer to the BRIDGE MODE section of this manual before attempting to use this mode. For each channel Speakon, the same impedance rules apply as with the binding posts. Internally , all the Speakons are wired in wha ...
-
PYLE Audio PTA3000 - page 8
(14) LOW CUT SWITCH This switch is used to activate the LOW CUT filter for the corresponding channel. It is again a push-push type switch, requiring a small "tool" to activate. The IN position routes the input signals through the 40 Hz LOW CUT filter , while the OUT position bypasses the filter . This filter will cut extremely low frequen ...
-
PYLE Audio PTA3000 - page 9
levels occur Then, as temperatures in the amplifier heat sinks increase, the automatic thermal-sensing circuitry will cause high-speed operation to occur . Depending upon signal conditions and amp loading, high-speed fan operation may continue or the fan may cycle continuously between high and low . This situation is quite normal. If cooling is ina ...
-
PYLE Audio PTA3000 - page 10
AMPLIFIER CONFIGURA TIONS ...
-
PYLE Audio PTA3000 - page 11
10 ...
-
PYLE Audio PTA3000 - page 12
100dB, unweighted 100dB, unweighted 100dB, unweighted 100dB, unweighted 100dB, unweighted 100dB, unweighted 100dB, unweighted 100dB, unweighted 10K Ohms per leg 10K Ohms per leg 10K Ohms per leg 10K Ohms per leg 10K Ohms per leg 10K Ohms per leg 10K Ohms per leg 10K Ohms per leg 300W RMS/chan 400W RMS/chan 500W RMS/chan 600W RMS/chan 700W RMS/chan ...
-
PYLE Audio PTA3000 - page 13
PyleAudio.com 718.535.1800 718.236.2400 (fax) 1600 63rd Street, Brooklyn NY 11204 ...
PYLE Audio PTA3000についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもPYLE Audio PTA3000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPYLE Audio PTA3000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。