Graco 235628の取扱説明書

22ページ 0.26 mb
ダウンロード

ページに移動 of 22

Summary
  • Graco 235628 - page 1

    Instructions – Parts List W A TERBASE COMP A TIBLE Ultra–lite t Pistol Grip Flo–Gun Model 235627, Series B 4000 psi (280 bar) Maximum Working Pressure T apered V alve Needle Model 235628, Series D 6000 psi (415 bar) Maximum Working Pressure Ball End V alve Needle, Abrasive Material Compatible Model 243775, Series B 6000 psi (415 bar) Maximum ...

  • Graco 235628 - page 2

    2 308253 Symbols W arning Symbol W ARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. W ARNING SKIN INJECTION HAZARD Spray from the gun, hose ...

  • Graco 235628 - page 3

    308253 3 W ARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and result in a fire or explosion and serious injury .  Ground the equipment and the object being sprayed. See Ground the System on page 5.  Provide fresh air ventilation to avoid the buildup of flammabl ...

  • Graco 235628 - page 4

    4 308253 T echnical Data Maximum Working Pressure Models 235627, 237607, and 237649 4000 psi (280 bar) . . . . . . . . . . . . . Models 235628 and 243775 6000 psi (415 bar) . . . Outlet Port Size All Models 1/4 npt(f) with nut for metal . . . . . . . . . . flanged nozzle Inlet Port Size Models 235627 and 237607 1/4 npt(f) . . . . . . . . . . . Mode ...

  • Graco 235628 - page 5

    308253 5 Installation Ground the System W ARNING FIRE AND EXPLOSION HAZARD T o reduce the risk of a fire, explosion, and serious injury , proper electrical grounding of every part of your system is essential. Read the warning section, FIRE AND EXPLOSION HAZARD , on page 3 and follow the grounding instructions below . The following grounding instruc ...

  • Graco 235628 - page 6

    6 308253 Operation Pressure Relief Procedure W ARNING SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally . Fluid under high pressure can be injected through the skin and cause a serious injury . T o reduce the risk of an injury from injection, splashing fluid, or mov- ing ...

  • Graco 235628 - page 7

    308253 7 Operation Dispensing 1. Start the fluid supply pump. 2. The fluid flow rate is controlled at the pump. Adjust the pump pressure to obtain the desired flow rate. It is recommended that you use the lowest pres- sure necessary to dispense the fluid. The pressure adjustment will depend on the hose length, the viscosity of the fluid, and the gu ...

  • Graco 235628 - page 8

    8 308253 Service W ARNING SKIN INJECTION HAZARD T o reduce the risk of a serious injury , including fluid injection,  Follow the Pressure Relief Procedure on page 6 when you stop dispensing, before servicing the gun, and whenever you are instructed to relieve the pressure.  After adjusting or servicing the gun, make sure the fluid will not tr ...

  • Graco 235628 - page 9

    308253 9 Service Adjusting the V alve The trigger travel and corresponding valve opening are factory set to 1 inch (25.4 mm). T o adjust this setting, follow the procedure below . W ARNING SKIN INJECTION HAZARD T o reduce the risk of a serious injury , including fluid injection, follow the Pres- sure Relief Procedure on page 6 whenever you are inst ...

  • Graco 235628 - page 10

    10 308253 Service V alve Stem and Seal Service If fluid leaks past the v-block seal (3), the v-block seal or valve stem (24) may be worn or damaged. T o replace the seal or valve stem, follow the procedure below . W ARNING SKIN INJECTION HAZARD T o reduce the risk of a serious injury , including fluid injection, follow the Pres- sure Relief Procedu ...

  • Graco 235628 - page 11

    308253 1 1 Service NOTES: T orque to 6–10 in-lbs (0.68–1.13 N  m) Models 235627, 237607, & 237649: T orque to 70–80 in-lbs (7.9–9.0 N  m) Models 235628 and 243775: T orque to 100–125 in-lbs (1 1.3–14.1 N  m) Apply lithium base grease to threads Apply lithium base grease Models 235627, 237607, & 237649: T orque to 50–6 ...

  • Graco 235628 - page 12

    12 308253 Service Complete Disassembly and Assembly of the Gun (continued) Assembly 1. Follow steps 9 to 1 1 on page 10. 2. Lubricate the o-rings (5 and 6) and install them into the gun body . 3. Follow steps 12 to 14 on page 10. 4. Lubricate the trigger pivot holes (a) bracket guide (b), and rod (13). 5. Install the trigger (29) with the rod (13) ...

  • Graco 235628 - page 13

    308253 13 Service NOTES: T orque to 6–10 in-lbs (0.68–1.13 N  m) Models 235627, 237607, & 237649: T orque to 70–80 in-lbs (7.9–9.0 N  m) Models 235628 and 243775: T orque to 100–125 in-lbs (1 1.3–14.1 N  m) Apply lithium base grease to threads Apply lithium base grease When removing fluid hose, use wrench on end of fluid tu ...

  • Graco 235628 - page 14

    14 308253 Parts Models 235627 and 237607 Pistol Grip Flow Gun 22 *  26 *  5 *  24 21 4 28 27 *  3 *  1 20 7 2 17 8 29 15 9 14 6 19 *  8 *  13 35 34 05446 ...

  • Graco 235628 - page 15

    308253 15 Parts Model 235627 Pistol Grip Flow Gun Ref. No. Part No. Description Qty . 1* 100975 NUT , hex; No. 5–40 1 2 102233 BALL 1 3* 102921 SEAL, v-block; polyurethane 1 4 102924 SPRING, compression 1 5* 103338 O-RING; fluoroelastomer 1 6 1 12085 O-RING; fluoroelastomer 1 7 1 1 1902 SPRING, compression 1 8* 1 12410 RING, retaining 2 9 1 1 190 ...

  • Graco 235628 - page 16

    16 308253 Parts Models 237649 Pistol Grip Flow Gun 04807 22  26  5  24 21 4 28 27  3  1 20 7 2 17 8 29 15 9 14 6 18 19  8  13 35 34 ...

  • Graco 235628 - page 17

    308253 17 Parts Model 237649 Pistol Grip Flow Gun Ref. No. Part No. Description Qty . 1  100975 NUT , hex; No. 5–40 1 2 102233 BALL 1 3  102921 SEAL, v-block; polyurethane 1 4 102924 SPRING, compression 1 5  103338 O-RING; fluoroelastomer 1 6 1 12085 O-RING; fluoroelastomer 1 7 1 1 1902 SPRING, compression 1 8  1 12410 RING, retaining ...

  • Graco 235628 - page 18

    18 308253 Parts Model 235628 Pistol Grip Flow Gun 05447A 22 *26 *24 *5 21 4 28 27 *3 *1 20 7 2 17 8 29 15 9 14 6 19 *8 *13 35 34 42 ...

  • Graco 235628 - page 19

    308253 19 Parts Model 235628 Pistol Grip Flow Gun Ref. No. Part No. Description Qty . 1* 100975 NUT , hex; No. 5–40 1 2 102233 BALL; stainless steel 1 3* 102921 SEAL, v-block; polyurethane 1 4 102924 SPRING, compression 1 5* 102982 O-RING; PTFE 1 6 1 1 1316 O-RING; CV75 1 7 1 1 1902 SPRING, compression 1 8* 1 12410 RING, retaining 2 9 1 1 1904 SC ...

  • Graco 235628 - page 20

    20 308253 Parts Model 243775 Pistol Grip Flow Gun 05447A 22 *26 *24 *5 21 4 28 27 *3 *1 20 7 2 17 8 29 15 9 14 6 19 *8 *13 35 34 42 ...

  • Graco 235628 - page 21

    308253 21 Parts Model 243775 Pistol Grip Flow Gun Ref. No. Part No. Description Qty . 1* 100975 NUT , hex; No. 5–40 1 2 102233 BALL; stainless steel 1 3* 102921 SEAL, v-block; polyurethane 1 4 102924 SPRING, compression 1 5* 102982 O-RING; PTFE 1 6 1 1 1457 O-RING; PTFE 1 7 1 1 1902 SPRING, compression 1 8* 1 12410 RING, retaining 2 9 1 1 1904 SC ...

  • Graco 235628 - page 22

    22 308253 Graco Standard W arranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by a n authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for ...

メーカー Graco カテゴリー Welder

Graco 235628のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 235628の取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco 235628の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco 235628の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco 235628の取り付け説明書、サービスマニュアル、簡易説明書、またはGraco 235628のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco 235628の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco 235628デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco 235628を使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco 235628ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco 235628の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco 235628の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco 235628に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco 235628デバイスの基本機能を使うにあたってのヒント。 Graco 235628のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco 235628に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco 235628のメーカー/サービスへの連絡先に関する情報。

Graco 235628についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco 235628の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco 235628で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)