Krell Industries MD10の取扱説明書

20ページ 1.04 mb
ダウンロード

ページに移動 of 20

Summary
  • Krell Industries MD10 - page 1

    MD-10 OWNER’S REFERENCE ...

  • Krell Industries MD10 - page 2

    A. INTRODUCTION TCrOngratulations on your purchase of the MD-10 CD anscription turntable and welcome to the KRELL family oF audio components. You ha.vejoined a select group of listeners who enjoy only tlae tlnest in music reproduction. We are dedicated to the~ development of technologically advanced components tor the reproduction o.f digat~ly reco ...

  • Krell Industries MD10 - page 3

    B. TABLE OF CONTENTS 3 4 6 9 11 12 15 16 18 19 UNPACKING AND ASSEMBLY DUST COVER INSTALLATION BASIC INSTALLATION AND CONNECTIONS OPERATION OF THE CD TRANSPORT REMOTE CONTROL TRACK AND FTS PROGRAMMING MAINTENANCE QUESTIONS AND ANSWERS SPECIFICATIONS WARRANTY AND SERVICE INFORMATION C. UNPACKING AND ASSEMBLY 1. Open the box and remove the top layer o ...

  • Krell Industries MD10 - page 4

    D. DUST COVER INSTALLATION 1. Looking at the front of the MD-10, locate the two black hinge block assemblies on the rear left and right corners. (Refer to location diagram) 2. Locate the hinge pin on the back of each hinge block assembly and pull them out gently until they are fully extended. t3 h. Open the flap only on the protective sleeve and lo ...

  • Krell Industries MD10 - page 5

    1 Dust cover 2 Hinge block 3 Adjustable suspension tower 4 Transport 5 Hinge pin 6 Cover pin 7 Bubble level MD-10 LOCATION DIAGRAM 5 ...

  • Krell Industries MD10 - page 6

    E. BASIC INSTALLATION AND CONNECTIONS 1. Place the unit on a clean, level surface away from excessive heat, moist.ure or light. Ideally, the MD-10 should be placed on tlae top of an audio component cat)i- net or other "open air" rigid platform. 2. The MD-10 may. be. placed in a cabinet. It will require. 17.0 inches of vertical clearance b ...

  • Krell Industries MD10 - page 7

    8. Connect the Digital Output from the MD-10 to a Krell Digital Processor or other compatible digital-to-analog audio processor. The MD-10 is compatible with industry standard Fibre ~O_[?tic, Coaxial RCA, AT&T wide bandwidth Fibre Optic ~1 type and AES/EBU XLR output connectors. NOTE: Care should be taken in selecting the type of cable used to ...

  • Krell Industries MD10 - page 8

    3. Connect your digital interlink between the transport , and digital-to-analog converter, if not already connectecl. 4. Select a digital source and press the TimeSync button on the front of your digital-to- analo~ converter. The corresponding led will-illuminate indicating the TimeS-ync is locked. Should the TimeSync-LED flash, tlais means the Tim ...

  • Krell Industries MD10 - page 9

    F. OPERATION OF THE CD TRANSPORT 1. Turn the CD transport ON by pressing the Power b.utton., The display will illuminate. Select a disc an.d place it on the spindl~e, label side up. Put the disc st.alfi- fizer on the center ot the CD so it fits securely on tide drive spindle. CAUTIONS: Never operate the CD transport without the disc stabilizer. Thi ...

  • Krell Industries MD10 - page 10

    3. Select a track on the CD to play with the remote con- trol or via the front panel and press the Play button. The music will now began. 10 ...

  • Krell Industries MD10 - page 11

    G. REMOTE CONTROL 1. The operating functions of the Remote Control are describei] below: POWER STOP PLAY PAUSE TRACK I< TRACK >1 INDEX I< INDEX >l SEARCH I< SEARCH >l FTS PROGRAM RPT Turns unit ON or OFF Stops the disc from playing Starts the disc playing at. track 1; will also restart pray of the current track Tem.porarily stops ...

  • Krell Industries MD10 - page 12

    H. TRACK PROGRAMMING The remote control or the front panel of the MD-10 can be used to program specific tracks on a disc to be played in the order you choose. The MD-10 can store up to 20 selections per program. 1. Select the track number which will start the sequence into the keypad, then push the PROGRAM or PROGR button. A ’~" will appear ...

  • Krell Industries MD10 - page 13

    FTS PROGRAMMING To program tracks in the FTS memory: NOTE: Before you begin,place disc to be progra.mmed on the unit and press PLAY. Once the unit reacls the table of contents and displays the disc’s playing_ time,press STOE You can now begin programming the FTS memory. 1. Program the selections in the standard form described above. ~ . After you ...

  • Krell Industries MD10 - page 14

    TO ERASE FTS PROGRAM MEMORY NOTE: FTS memory can only be erased via the front panel controls. The remote control cannot erase FTS memory. NOTE: The disc does not have to be on the MD-10 to ~ rase FTS memory. Erasure can be completed with no isc on the drive spindle. ~ . Press the FTS button on the front panel. Hold the . u.tton in while pressingthe ...

  • Krell Industries MD10 - page 15

    I. MAINTENANCE .B.e.cause of its superb build quality the MD-10 requires little maintenance. Should tlie unit become excesslvly dirty, clean the lens assembly with a camera lens brush made of a soft material like camel hair. The acrylic top p!ate and dust cover should be cleaned with the poli~stiing .kit provided. Read the directions on the contain ...

  • Krell Industries MD10 - page 16

    J. OUESTIONS AND ANSWERS Q. My Digital to Analog ~processor will accommodate either fibre optic or coaxial digital inputs. Which output should I use on the MD-10? A. While a high quality coaxial willperform quite well, we re.commend glass fibre optic cabre due to its ab.ility to completely isolate the grounding planes between the. transport and pro ...

  • Krell Industries MD10 - page 17

    t~. Due to the exposed nature of the laser assembly is ere a possibility of damage through laser radiation? A. No. There is. an optical sensor under the CD when it is positione~l on tlae transport hub. This allows the MD-10 to p.rohibit the laser from turning on wlaen it is not cov- erecl with a CD. a~I own many CDs that have CD Rings on them. Am I ...

  • Krell Industries MD10 - page 18

    K. SPECIFICATIONS TRANSPORT Modified Philips CDM-4 PRO with Hall effect motor, swing-arm design LASER Single Beam with glass lens OUTPUT Digital only in industry standard SP_DIF format. 1 FIBRE OPTIC via standard intertace 1 COAXIAL via RCA connector 1 AT&T via ST connector 1 AES/EBU via XLR connector 1 SPECIAL Optional TimeSync via ST connecto ...

  • Krell Industries MD10 - page 19

    L. WARRANTY AND SERVICE INFORMATION There are no user-serviceable parts inside the MD-10. The MD-10 has a limited warranty of three years parts and labor on transport-related parts; five years parts an.d labor on electronic parts, lleturn freight is included in the warranty. The warranty period b.egins on thee date of p_u_rchase and is activated wi ...

  • Krell Industries MD10 - page 20

    0 0 I 0 I 0 ’ DIGITAL INC. KRELL DIGITAL INC. 35 HIGGINS DRIVE MILFORD CT 06460 SALES 203-874-3139 FAX 203-878-8373 COPYRIGHT 1992 KRELL DIGITAL INC. (MD109209) ...

メーカー Krell Industries カテゴリー Turntable

Krell Industries MD10のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MD10の取扱説明書
- Krell Industriesの製品カード
- パンフレット
- またはKrell Industries MD10の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Krell Industries MD10の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Krell Industries MD10の取り付け説明書、サービスマニュアル、簡易説明書、またはKrell Industries MD10のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Krell Industries MD10の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Krell Industries MD10デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKrell Industries MD10を使用するのを助ける技術的文書のことです。説明書は通常、全てのKrell Industries MD10ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Krell Industriesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Krell Industries MD10の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKrell Industries MD10の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Krell Industries MD10に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Krell Industries MD10デバイスの基本機能を使うにあたってのヒント。 Krell Industries MD10のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Krell Industries MD10に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKrell Industries MD10のメーカー/サービスへの連絡先に関する情報。

Krell Industries MD10についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKrell Industries MD10の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKrell Industries MD10で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)