American Dryer Corp. 20/31の取扱説明書

12ページ 0.48 mb
ダウンロード

ページに移動 of 12

Summary
  • American Dryer Corp. 20/31 - page 1

    Se rvice Procedures for the Model 20/31 D ryers Electric and Hot Surface Ignitor Gas ADC Part No. 450262 American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: (508) 678-9000 / Fax: (508) 678-9447 e-mail: techsupport@amdry.com www.amdry.com ...

  • American Dryer Corp. 20/31 - page 2

    T able of Contents Par t Locations and R emo val ........................................ 3 Lower Front Panel Removal ............................................................. 3 Upper Front Panel Removal ............................................................. 3 T op Cover Removal ........................................................... ...

  • American Dryer Corp. 20/31 - page 3

    450262-1 www .amdry .com 3 P ar t Loca tions and R emo val UPPER FRONT PANEL REMOV AL: Remove the four screws located just above the loading door . T ilt the bottom of the panel out and lift the panel up and away from the dryer . LOWER FRONT PANEL REMOV AL: Remove the lint drawer . Remove the four screws located just below the loading door . T ilt ...

  • American Dryer Corp. 20/31 - page 4

    4 American Dryer Corp. 450262-1 Remove screws and nuts at the rear of the lint box. Unplug wires from the capacitor . T o remove motorized impellor assembly , remove the five screws and four nuts, shown with arrows. Remove cover and pull the motorized impellor assembly out through the opening. Unplug three connections at the left of the lint box. T ...

  • American Dryer Corp. 20/31 - page 5

    450262-1 www .amdry .com 5 GAS V A L VE/IGNITION SYSTEM REMOV AL: Be sure to shut off the gas main and then proceed to remove electrical connections and screws indicated. Remove lower front panel. Disconnect union and screws noted with arrows. The gas valve and burner orifice can now be carefully pulled toward the front of the dryer . Be sure to pu ...

  • American Dryer Corp. 20/31 - page 6

    6 American Dryer Corp. 450262-1 TUMBLER SUPPORT WHEEL ASSEMBL Y REPLACEMENT : The front wheel assemblies can be replaced with the lower front panel removed. Remove the three bolts by reaching upward with a socket or box wrench. The illustration below is provided to show the location of these wheels as the wheels cannot easily be seen while standing ...

  • American Dryer Corp. 20/31 - page 7

    450262-1 www .amdry .com 7 TUMBLER ALIGNMENT : Proper alignment is achieved by making the gap between the tumbler and openings in the front and rear bulkheads equal on all sides. The front to bulkhead may be checked for accuracy by using a thickness gauge. The rear gap is not accessible. Marking the position of the rear wheel brackets before removi ...

  • American Dryer Corp. 20/31 - page 8

    8 American Dryer Corp. 450262-1 BEL T REPLACEMENT Shut off electrical power . Disconnect wiring leading to the tumbler support p anel. Remove the back guard, top, and the exhaust support bracket. Unbolt and remove the thrust washers from the rear of the tumbler shaft. While someone holds the tumbler through the loading door remove all six screws fr ...

  • American Dryer Corp. 20/31 - page 9

    450262-1 www .amdry .com 9 PLACING THE BEL T BACK ON THE MOT OR SHEA VE: REQUIRED ITEMS: 3 foot Section of 1-1/2” Electrical T ubing Replacement Belt T o stretch the belt back onto the sheave involves using a two foot length of 1-1/2” electrical tubing (Fig. 1). Preparing the end of the tubing as shown makes it easier to use. Position the belt ...

  • American Dryer Corp. 20/31 - page 10

    10 American Dryer Corp. 450262-1 Electrical Component Locations ELECTRICAL P ANEL: The electrical panel is located behind the front upper panel. DOOR SWITCH MICROPROCESSOR ROT A TION SENSOR ...

  • American Dryer Corp. 20/31 - page 11

    450262-1 www .amdry .com 11 ELECTRIC OVEN EXHAUST PROBE, EXHAUST HI-LIMIT , AND LINT DRA WER SWITCH: T emperature probe and exhaust hi-limit are accessible once the lint box is removed. The lint drawer switch can be removed after the cover has been removed. FIRE SUPPRESSION SYSTEM ITEMS, TERMINAL BLOCK, AND AXIAL TEMPERA TURE PROBE Located behind b ...

  • American Dryer Corp. 20/31 - page 12

    ADC Part No. 450262 1 - 02/25/05 ...

メーカー American Dryer Corp. カテゴリー Clothes Dryer

American Dryer Corp. 20/31のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 20/31の取扱説明書
- American Dryer Corp.の製品カード
- パンフレット
- またはAmerican Dryer Corp. 20/31の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、American Dryer Corp. 20/31の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、American Dryer Corp. 20/31の取り付け説明書、サービスマニュアル、簡易説明書、またはAmerican Dryer Corp. 20/31のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、American Dryer Corp. 20/31の製品を使用するにあたって最も人気のある説明書を閲覧できます。

American Dryer Corp. 20/31デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAmerican Dryer Corp. 20/31を使用するのを助ける技術的文書のことです。説明書は通常、全てのAmerican Dryer Corp. 20/31ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

American Dryer Corp.の取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. American Dryer Corp. 20/31の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAmerican Dryer Corp. 20/31の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。American Dryer Corp. 20/31に関してこのドキュメントで見つけることができる全てのヒントの目次
3. American Dryer Corp. 20/31デバイスの基本機能を使うにあたってのヒント。 American Dryer Corp. 20/31のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。American Dryer Corp. 20/31に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAmerican Dryer Corp. 20/31のメーカー/サービスへの連絡先に関する情報。

American Dryer Corp. 20/31についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAmerican Dryer Corp. 20/31の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAmerican Dryer Corp. 20/31で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)