M-Systems Flash Disk Pioneers 45-SR-001-01-7Lの取扱説明書

22ページ 0.15 mb
ダウンロード

ページに移動 of 22

Summary
  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 1

    Section II- User Manual FFD 3.5" SCSI Flash Disk MARCH -2002 45-SR-001-01- 7L REV 4.0 ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 2

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 2 of 22 Table of Contents 1 Genera l.................................................................................................................................... 3 2 Kit Co ntents ............................................................................................... ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 3

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 3 of 22 1 General This manual provides y ou with the information y ou need to properly install your new FF D 3.5 " SCSI Flash drive. M-Sy stems recommends that only properly qualified and trained personnel install the drive. The following sections contain information about han ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 4

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 4 of 22 4 Handling Instructions You can prolong the life of y our FFD, increase its reliability and prevent unnecessary damage by following the instr uctions listed below. Fa ilure to follow any of these instructions may void your warranty . • Alway s take all proper ESD precauti ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 5

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 5 of 22 5 Installation 5.1 Sy stem Requirements I n order to install the FFD in y our system, ensure that y ou have the following items: • Sy stem mounting hardware • 4-pin power cable • 50-pin ribbon SCSI cable • SCSI host adapter • Appropriate device driver for y our op ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 6

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 6 of 22 Table 1: SCSI I D DI P Sw itch Sett ings SCSI ID Sw itch 3 Sw itch 2 Sw itch 1 0 1 OFF OFF OFF 1 OFF OFF ON 2 OFF ON OFF 3 OFF ON ON 4 ON OFF OFF 5 ON OFF ON 6 ON ON OFF 7 ON ON ON 1 Defa ult factory setting 5.2.2 Termination The SCSI bus must be terminated at the two phy s ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 7

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 7 of 22 5.2.3 Termination Pow er (TRM PWR) Termination power must be supplied by at least one device on the SCSI bus; it is normally supplied by the host adapter. However, if y ou are unsure whether TRMPWR is available in y our sy stem, y ou can configure the FF D to supply TRMPWR. ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 8

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 8 of 22 5.3 FFD 3.5 " SCSI Flash Disk Drive Installation The FFD can be installed in any mounting position in the sy stem. Unlike rotating disks that have an axis of rotation, the FFD is not susceptible to damage due to orientation. Note: It is not necessary to perform a low- ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 9

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 9 of 22 SCSI device 0 not terminated SCSI device 1 Terminated SCSI device 3 Terminated through SCSI device 0 not terminated SCSI device 2 not terminated SCSI device 5 Terminated Only internal devices: Only external devices: Internal and external devices: External Terminator > ^ ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 10

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 10 of 22 5.3.2 Using the FFD on a DOS-Based Platform After phy sically installing the F FD, it must be installed as a disk drive under DOS. Run the DOS commands listed below and follow the instructions display ed for each command. For more information regarding the DOS commands, re ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 11

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 11 of 22 I n order to proceed with the installation, y ou must have Supervisor privileges on y our UNIX sy stem. I f y ou do not have these privileges, contact y our system administrator. To install the FF D as a drive under UNIX: 1. Run the UNI X format utility a nd follow the dis ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 12

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 12 of 22 6 Driv e Parameters Most SCSI device drivers can automatically detect the total number of sectors on the FFD, using the READ CAPACITY command, and config ure them accordingly . However, some older device drivers must obtain the drive geometry parameters manually. The phy s ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 13

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 13 of 22 Unforma tted Disk 1 Capacity (MB) Formatted Disk Capacity (# of blocks) 2 Cylinders Heads Sector/ Cylinder Bytes/ Sector 2,048 3D68FFH F5AH 10H 40H 512 2,176 413FFFH 1050H 10H 40H 512 2,304 4516FFH 1145H 10H 40H 512 2,432 48EDFFH 123BH 10H 40H 512 2,560 4CC4FFH 1331H 10H 4 ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 14

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 14 of 22 7 LED Indicators and Configuration Sw itch Figure 4 illustrates the two L EDs located on the FFD fr ont panel. Table 6 Descr ibes the L ED color codes and status definitions. Figure 4: Front Panel LED I ndicators Table 6: LED Status Descr iption Status LED Color Indicat or ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 15

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 15 of 22 8 Troubleshooting 8.1 Built-In Self Test The FFD performs a self-test during power up. I f the test fails, the green LED flashes at a rate of 1 Hz. If y ou encounter this problem, please contact your dealer or technical support. 8.2 Common Problems The following sections d ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 16

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 16 of 22 6. Attach the SCSI cable to the host adapter and to the last device. Do not forg et the device’s power connector. 7. Power ON the PC and verify that the host adapter recog nizes the SCSI device. 8. If the SCSI device is recognized, power OFF the PC and install the next d ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 17

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 17 of 22 8.2.4 Solving Installation Problems The problems that arise in most installations are described below. Unstable Termination This occurs when there is a passive termination with Fast-SCSI devices on the bus. Incorrect Termination This occurs when there are too many devices ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 18

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 18 of 22 9 Getting Help For technical assistance with the installation and configuration of y our FFD, contact one of the sources listed below. Please have the following information available to aid the customer support representative in providing y ou with the best possible guidan ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 19

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 19 of 22 10 Frequently A sked Questions (FA Qs) A bout SCSI Q: What is SCSI? A: SCSI (Small Com puter System I nterface) is a general-purpose, parallel bus sy stem. It originated with Shugart’s 1979’ SASI (Shugart Associates Sy stem Interface), and Shug art and NCR presented it ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 20

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 20 of 22 Q: What is Plug-and-play (P&P ) SCSI? A: Plug-and-play SCSI is an extension of the generic plug-and-play specification. P&P is an approach for defining an auto-configuring environment for I SA boards. One of the key features of P&P- SCSI is SCAM. Q: What is SCS ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 21

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 21 of 22 Q: What types of SCSI connectors are available? A: There are many different connectors for SCSI . Some of them were defined with SCSI -1 and are now obsolete, such as the DB-50 connector. The most common connectors in use today are the 50-pin Centronics-ty pe SCSI -1 conne ...

  • M-Systems Flash Disk Pioneers 45-SR-001-01-7L - page 22

    FFD 3.5 " SCSI Flash Disk User Manual 45-SR-001-01- 7L REV 4.0 22 of 22 How to Contact Us Internet: http://www.m-sy s.com E-m ail: info@m-sy s.com USA Off ice: M-Sy stems I nc. 8371 Central Ave, Suite A Newark CA 94560 Phone: +1-510-494-2090 Fax: +1-510-494-5545 Taiwan Off ice: Room B, 13 F, No. 133 Sec. 3 Min Sheng East Road Taipei, Taiwan R. ...

メーカー M-Systems Flash Disk Pioneers カテゴリー Flash Memory

M-Systems Flash Disk Pioneers 45-SR-001-01-7Lのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 45-SR-001-01-7Lの取扱説明書
- M-Systems Flash Disk Pioneersの製品カード
- パンフレット
- またはM-Systems Flash Disk Pioneers 45-SR-001-01-7Lの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、M-Systems Flash Disk Pioneers 45-SR-001-01-7Lの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、M-Systems Flash Disk Pioneers 45-SR-001-01-7Lの取り付け説明書、サービスマニュアル、簡易説明書、またはM-Systems Flash Disk Pioneers 45-SR-001-01-7Lのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、M-Systems Flash Disk Pioneers 45-SR-001-01-7Lの製品を使用するにあたって最も人気のある説明書を閲覧できます。

M-Systems Flash Disk Pioneers 45-SR-001-01-7Lデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがM-Systems Flash Disk Pioneers 45-SR-001-01-7Lを使用するのを助ける技術的文書のことです。説明書は通常、全てのM-Systems Flash Disk Pioneers 45-SR-001-01-7Lユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

M-Systems Flash Disk Pioneersの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. M-Systems Flash Disk Pioneers 45-SR-001-01-7Lの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははM-Systems Flash Disk Pioneers 45-SR-001-01-7Lの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。M-Systems Flash Disk Pioneers 45-SR-001-01-7Lに関してこのドキュメントで見つけることができる全てのヒントの目次
3. M-Systems Flash Disk Pioneers 45-SR-001-01-7Lデバイスの基本機能を使うにあたってのヒント。 M-Systems Flash Disk Pioneers 45-SR-001-01-7Lのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。M-Systems Flash Disk Pioneers 45-SR-001-01-7Lに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるM-Systems Flash Disk Pioneers 45-SR-001-01-7Lのメーカー/サービスへの連絡先に関する情報。

M-Systems Flash Disk Pioneers 45-SR-001-01-7Lについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもM-Systems Flash Disk Pioneers 45-SR-001-01-7Lの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがM-Systems Flash Disk Pioneers 45-SR-001-01-7Lで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)