3M 78-0013-4441-1-Dの取扱説明書

12ページ 3.73 mb
ダウンロード

ページに移動 of 12

Summary
  • 3M 78-0013-4441-1-D - page 1

    3M ™ One Pass Mini FiberPathw ay Installation Instructions December 2012 78-0013-4441-1-D 3 The Network of Networks. ...

  • 3M 78-0013-4441-1-D - page 2

    2 78-0013-4441-1-D 3M ™ One Pass Mini F iber Pathway Contents 1.0 System Overvie w ............................................................................................................................ 3 2.0 Components and Accessories ......................................................................................................... 3 ...

  • 3M 78-0013-4441-1-D - page 3

    78-0013-4441-1-D 3 3M ™ One Pass Mini F iber Pathway 1.0 System Over view The One Pass Mini Fiber P athway is designed for use in FTTP (Fiber-to-the-Premise) netw orks within brownfield or greenfield Multi Dwelling Units (MDUs). The One Pass Mini Fiber Pathway is a surf ace-mount, adhesive-back ed drop cable and pathway solution designed for indo ...

  • 3M 78-0013-4441-1-D - page 4

    4 78-0013-4441-1-D 3M ™ One Pass Mini F iber Pathway 3.2 ILU installation tools are wear items, and should be replaced on a bi-annual basis, or approximately ev ery 500 installed units. Sooner as required. 3.3 Additional Recommended T ools (Not Included) A B D E F C G H a) Drill b) Stapler c) Splicer’ s Knife d) Fiber Snips e) ScotchBlue ™ Pa ...

  • 3M 78-0013-4441-1-D - page 5

    78-0013-4441-1-D 5 3M ™ One Pass Mini F iber Pathway 4.3 Hang weight from strip. Release tab T ab hole 4.4 Remov e successful test strips by pulling on release tab T est W eight Hang Time Result > 60 seconds P ASS – Install < 60 second F AIL – Do not install The path the duct will follow MUST be clean and dry . • Clean all surfaces al ...

  • 3M 78-0013-4441-1-D - page 6

    6 78-0013-4441-1-D 3M ™ One Pass Mini F iber Pathway • Do not remov e duct from box. Route end through handle as shown and pay of f duct. 6.0 Exposing Fiber For T ermination Expose 2-4' (610-1220 mm) of fiber fr om the end of the duct before terminating using the following method: 6.1 Snip the flange on either side of the duct, being caref ...

  • 3M 78-0013-4441-1-D - page 7

    78-0013-4441-1-D 7 3M ™ One Pass Mini F iber Pathway 7.3 After exposing appropriate length of f iber for termination, attach duct by aligning the end of the duct with the recessed area in the base. Remov e the liner and press firmly into place. DO NOT ROUTE the 900 µm fiber into the outlet box until installation of the duct and termination of th ...

  • 3M 78-0013-4441-1-D - page 8

    8 78-0013-4441-1-D 3M ™ One Pass Mini F iber Pathway 10.0 Planar Cor ner Installation 10.1 Peel adhesi ve liners and attach support in duct path. Marking grooves Mark flange at groove Leave 12" (300 mm) of liner intact 10.2 T rim the duct flange using the 3M ™ One Pass Mini Duct Flange Remov al T ool. Example direction of travel Align mar ...

  • 3M 78-0013-4441-1-D - page 9

    78-0013-4441-1-D 9 3M ™ One Pass Mini F iber Pathway 11.0 Mechanical Anchor Installation 11.1 Remov e liner, align groo ve with duct and press firmly into place. The anchor may be secured with a T -25 staple if desired. T -25 Staple here (optional) • Use the adhesi ve-backed anchor where ver additional adhesion is required, such as: high stress ...

  • 3M 78-0013-4441-1-D - page 10

    10 78-0013-4441-1-D 3M ™ One Pass Mini F iber Pathway 14.0 Connector T ermination and Final Steps 14.1 T erminate the f iber using a 3M ™ No Polish Connector or 3M ™ Crimplok+ Connector . Anchor furcation tubing Feed through from living unit 3M ™ One Pass Point-of-Entry Box (Hallway Side) 14.2 In buildings where the One P ass Fiber Pathway ...

  • 3M 78-0013-4441-1-D - page 11

    78-0013-4441-1-D 11 3M ™ One Pass Mini F iber Pathway 15.0 Fiber Repair 15.1 Ensure that the root cause for service interruption is damaged 900 µm. 15.2 W orking away from the W all Outlet, mak e small window cuts using the W indow Cut T ool at e very other corner or turn. Note: Additional window cuts at other corners may be made if needed. Wind ...

  • 3M 78-0013-4441-1-D - page 12

    3M and ScotchBlue are trademarks of 3M Company . Important Notice All statements, technical information, and recommendations related to 3M’ s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intend ...

メーカー 3M カテゴリー Doll

3M 78-0013-4441-1-Dのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 78-0013-4441-1-Dの取扱説明書
- 3Mの製品カード
- パンフレット
- または3M 78-0013-4441-1-Dの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、3M 78-0013-4441-1-Dの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、3M 78-0013-4441-1-Dの取り付け説明書、サービスマニュアル、簡易説明書、または3M 78-0013-4441-1-Dのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、3M 78-0013-4441-1-Dの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

3M 78-0013-4441-1-Dデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーが3M 78-0013-4441-1-Dを使用するのを助ける技術的文書のことです。説明書は通常、全ての3M 78-0013-4441-1-Dユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

3Mの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. 3M 78-0013-4441-1-Dの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにはは3M 78-0013-4441-1-Dの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。3M 78-0013-4441-1-Dに関してこのドキュメントで見つけることができる全てのヒントの目次
3. 3M 78-0013-4441-1-Dデバイスの基本機能を使うにあたってのヒント。 3M 78-0013-4441-1-Dのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。3M 78-0013-4441-1-Dに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国における3M 78-0013-4441-1-Dのメーカー/サービスへの連絡先に関する情報。

3M 78-0013-4441-1-Dについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでも3M 78-0013-4441-1-Dの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかが3M 78-0013-4441-1-Dで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)