Onkyo HT-R8230の取扱説明書

40ページ 2.21 mb
ダウンロード

ページに移動 of 40

Summary
  • Onkyo HT-R8230 - page 1

    Contents Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. HT-R8230 Appendix Tr ...

  • Onkyo HT-R8230 - page 2

    2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y heat so ...

  • Onkyo HT-R8230 - page 3

    3 Precautions For U.S. models Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of ca ...

  • Onkyo HT-R8230 - page 4

    4 Features Amplifier Features •5 × 100 W/Channel @ 8 Ω , 20–20 kHz, 0.08% THD • WRAT-Wide Range Amplifier Technology • Optimum Gain Volume Circuitry • DTS, Dolby Digital, Dolby Pro Logic II • CinemaFILTER • Non-Scaling Configuration • A-Form–Auto Format Sensing • Linear PCM 96 kHz/24-bit D/A Converters • Advanced 24-bit DSP ...

  • Onkyo HT-R8230 - page 5

    5 Bef ore Using the HT -R8230 30 ˚ 30 ˚ Approx. 16 feet (5m) Remote control sensor Standby indicator HT-R8230 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. 3 Close the battery compartment. Notes • The supplied batteries should last for about six months, although this will var ...

  • Onkyo HT-R8230 - page 6

    6 Front panel Inde x to par ts and contr ols For operational instructions, refer to the page indicated in brackets. 1 STANDBY/ON button [17] When STANDBY/ON button is pressed to ON, the display will light to show the current volume setting for about 5 seconds then show the current sound input source. Pressing the button again returns the HT-R8230 t ...

  • Onkyo HT-R8230 - page 7

    7 ab c d e f g hi Display @ DISPLAY button [25] Each time you press the DISPLAY button, the display changes. # AUDIO SELECTOR button [26, 27] Press to select an audio input signal format other than FM and AM. Each time this button is pressed, the setting cycles. $ Input selector buttons (DVD, VIDEO 1, VIDEO 2, VIDEO 3, TAPE, TUNER, and CD) [17, 21- ...

  • Onkyo HT-R8230 - page 8

    8 Index to parts and controls Rear panel For operational instructions, refer to the page indicated in brackets. 1 REMOTE CONTROL [16] Connect the Onkyo components that have connectors such as a CD player, and cassette tape deck using the cables provided with them. When these components are interconnected, they can be controlled from the remote cont ...

  • Onkyo HT-R8230 - page 9

    9 Explanations on this page are for controlling the HT-R8230. To operate other components, see “Using the remote controller with your other AV components” on pages 33 through 34. For operational instructions, refer to the page indicated in brackets. 1 SLEEP button [25] For setting the sleep time. This button is provided only on the remote contr ...

  • Onkyo HT-R8230 - page 10

    10 RL RL FRONT SPEAKERS A FRONT SPEAKERS B RL SURROUND SPEAKERS CENTER SPEAKER AC OUTLET ANTENNA FM 75 AM RL RL AUDIO OUT (PLA Y) AUDIO IN (REC) RL AUDIO OUT (PLA Y) DIGIT AL OUT OPTICAL VIDEO IN Connecting to audio/video equipment Audio connection cable (Analog signal) Optical fiber cable (Digital signal) Optical plug Signal flow Audio (R) Cassett ...

  • Onkyo HT-R8230 - page 11

    11 RL RL FRONT SPEAKERS A FRONT SPEAKERS B RL SURROUND SPEAKERS CENTER SPEAKER AC OUTLET ANTENNA FM 75 AM DIGIT AL OUT VIDEO OUT AUDIO OUT VIDEO IN AUDIO IN RL R L L R L R VIDEO OUT AUDIO OUT VIDEO OUT AUDIO OUT L R VIDEO OUT FRONT CENTER SUBWOOFER SURR L R AUDIO OUT COAXIAL DVD player or component with 5.1 ch output (DVD)* 1 Video cassette player ...

  • Onkyo HT-R8230 - page 12

    12 P ositioning speaker s/Connecting speaker s Two speaker systems can be connected to the Receiver. The speaker system A is to be placed in the main room, and the speaker system B is to be placed in a second room. The speaker system A consists of the FRONT SPEAKERS A (L/R), CENTER SPEAKER, SURROUND SPEAKERS (L/R) and SUBWOOFER. You can reproduce t ...

  • Onkyo HT-R8230 - page 13

    13 Positioning speakers/Connecting speakers Before connecting • Refer also to the instruction manuals of the speakers. • Be sure to connect the positive and negative cables for the speakers properly. If they are mixed up, the left and right signals will be reversed and the audio will sound unnatural. • Connect speakers with an impedance betwe ...

  • Onkyo HT-R8230 - page 14

    14 ANTENNA FM 75 AM Connecting the supplied FM and AM indoor antennas Connecting antennas Note Insert one end of the AM antenna cord to either of the AM antenna connectors and the other end to the other connector. There is no difference between one end of the AM antenna cord and the other end, unlike the speaker cables which have positive and negat ...

  • Onkyo HT-R8230 - page 15

    15 Connecting an Outdoor FM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. FM 75 Notes • Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft. • For best results, install the outdoor FM an ...

  • Onkyo HT-R8230 - page 16

    16 Connections f or remote contr ol ( ) Notes • Connect the plugs securely. • Be sure to connect to the connectors using the cable. • For proper operation the audio connection cables must be connected. This applies to both remote and standard operation. • If a component has two terminals, you can use either one to connect to the HT-R8230. T ...

  • Onkyo HT-R8230 - page 17

    17 Enjo ying m usic or videos with the HT -R8230 Connecting the power 1. Connect the power cord to a wall outlet. The HT-R8230 enters standby mode. The STANDBY indicator lights up. 2. Press STANDBY/ON. The AV Receiver turns on. The display on the AV Receiver’s front panel light. At the same time, the STANDBY indicator goes off. Note To turn off t ...

  • Onkyo HT-R8230 - page 18

    18 Speaker setup Front left Front right Center Surround left Surround right You need to set up the speaker configuration for the speaker system A (see page 12). (There is no speaker configuration setup for the speaker system B.) It is not necessary to set the parameters again once you have completed the setup unless you change the speaker configura ...

  • Onkyo HT-R8230 - page 19

    19 Speaker setup Specifying speaker distances To get the best from surround sound, it’s important that the sound from each speaker reaches the listener at the same time. To achieve this, you need to specify the distance from each speaker to the listening position. 1. Measure and make a note of the distance from each speaker to the listening posit ...

  • Onkyo HT-R8230 - page 20

    20 SUBWOOFER MODE TEST LEVEL CH SEL Adjusting each speaker ’ s relative volume balance — Test tone Adjust each speaker’s relative volume balance so that the volumes of all speakers’ test tones sound equal at the listening position. Adjust the volume to your normal listening level, prior to commencing settings. Note You cannot adjust the vol ...

  • Onkyo HT-R8230 - page 21

    21 Switch the source from TAPE to MD You can set the AV receiver to show “MD” when the TAPE source is selected by pressing TAPE on the unit. 1 Press TAPE to select the input source. 2 Press and hold TAPE on the unit until the display changes (for about 2 seconds). To restore the display Press and hold TAPE on the unit until the display changes ...

  • Onkyo HT-R8230 - page 22

    22 Listening to the radio Tuning into a radio station 1. Press TUNER. The selected band appears in the display. Each time you press the button, the band changes as follows: AM ↔ FM. e.g. When FM is selected. 2. Using the TUNING / buttons on the front panel, tune into the station you desire. When you tune into a radio station, TUNED indicator appe ...

  • Onkyo HT-R8230 - page 23

    23 PRESET TUNER PRESET/ADJUST TUNER MEMORY FM MODE Selecting preset stations Before selecting preset stations, you need to preset the radio stations. See “Presetting radio stations” on the left column of this page. 1. Press TUNER to switch the input source to the tuner. “FM” or “AM” appears in the display. The band selected in this step ...

  • Onkyo HT-R8230 - page 24

    24 MUTING SP A/SP B SPEAKERS A/B Muting the sound (remote controller only) Press MUTING. The MUTING indicator flashes in the display during the muting mode. To restore the sound, press MUTING again. Tip If you turn off the unit during muting, and turn it on again, the sound will be restored. Listening through headphones Connect the plug of the ster ...

  • Onkyo HT-R8230 - page 25

    25 DISPLAY DIMMER DIMMER SLEEP Changing the display Press DISPLAY. Each time you press DISPLAY, the screen changes as follows: When an input source other than FM or AM is selected FM/AM + Listening mode FM/AM frequency + Preset no. Input source + Listening mode (or Multich) Input source + volume Program format* Controlling the brightness of the dis ...

  • Onkyo HT-R8230 - page 26

    26 DVD AUDIO SELECTOR DVD LEVEL AUDIO SEL CH SEL Adjusting each speaker ’ s relative volume balance temporarily You can readjust each speaker’s relative volume balance according to your preference while listening to the sound. The adjusted values will return to the values set on page 20 when the AV Receiver enters standby mode unless you save t ...

  • Onkyo HT-R8230 - page 27

    27 DVD TAPE AUDIO SELECTOR DVD AUDIO SEL DIRECT SURROUND CH SEL LEVEL DIRECT SURROUND Using analog multi channel input The multi channel input refers to a system, which is compatible with a source component equipped with analog 5.1-channel outputs (DVD player, MPEG decoder, etc.), reproducing the left/right front, center and left/right surround cha ...

  • Onkyo HT-R8230 - page 28

    28 The surround sound of the AV Receiver enables you to enjoy the presence of a movie theater or concert hall in your room. Before using any surround mode, make sure the Speaker Setup configurations have been set (see page 18). The speaker configuration is very important for the surround sound. See “Positioning speakers/Connecting speakers” on ...

  • Onkyo HT-R8230 - page 29

    29 Selecting the listening mode Before operating the remote controller, press RCVR/TAPE. Press one of the listening mode buttons. DIRECT button : Set the listening mode to “Direct”. STEREO button : Set the listening mode to “Stereo”. SURROUND button : Set the listening mode to “PLII” (when the sound is analog, PCM or Dolby Digital stere ...

  • Onkyo HT-R8230 - page 30

    30 Using the audio adjust functions Before operating the remote controller, press RCVR/TAPE. These functions only work with speaker system A. Audio Adjust provides various functions for adjusting the sound, including several especially for use with Dolby Digital, DTS, and Pro Logic II source. The following table lists the Audio Adjust functions, th ...

  • Onkyo HT-R8230 - page 31

    31 The Audio Adjust functions are explained below. Bass With this function you can boost or cut low-frequency sounds output by the front speakers from –12 dB to +12 dB in 2 dB steps. Treble With this function you can boost or cut high-frequency sounds output by the front speakers from –12 dB to +12 dB in 2 dB steps. Late Night (Only for Dolby D ...

  • Onkyo HT-R8230 - page 32

    32 To record the input source signal you are currently watching or listening to Recording of video and/or audio signals can be performed on the components connected to the VIDEO 1 OUT and TAPE OUT (audio only) jacks. Recor ding a sour ce Recording the video from one source and the audio from another You can add the sound from one source to the vide ...

  • Onkyo HT-R8230 - page 33

    33 Using the remote contr oller with y our other A V components Connecting your Onkyo CD player, Onkyo DVD player, or Onkyo cassette recorder to the HT-R8230’s connector allows you to control it with the HT-R8230’s remote controller. Since you only need to point the remote controller at the HT-R8230, you can control components that are out of s ...

  • Onkyo HT-R8230 - page 34

    34 Using the remote controller with your other AV components 1. TAPE input selector 2. RCVR/TAPE Tape mode (RCVR/TAPE) 3. Tape deck operation buttons 4. DVD operation buttons 2. CD CD mode 1. CD input selector : Power On/Off. : Starts playback of CD. : Stops playback, fast forward or fast reverse. : Fast forwards of CD. : Fast reverses of CD. : Let ...

  • Onkyo HT-R8230 - page 35

    35 Causes • The power cord is disconnected. • There is external noise interfering with the computer circuits of the A V receiver . • Amplifier protection circuitry has been activated. • Power supply fluctuations or other abnormalities such as static electricity may interrupt correct operation. • The muting function is activated. • The A ...

  • Onkyo HT-R8230 - page 36

    36 When incorrect operation is observed • The HT-R8230 contains an internal microcomputer that performs high-level operations. However, on extremely rare occasions, noise or interference from an external source or static electricity may cause faulty operation. If this occurs, unplug the power cord from the wall outlet, wait five or more seconds, ...

  • Onkyo HT-R8230 - page 37

    37 Specifications Amplifier Section Power Output: Front L/R: 100 W + 100 W Center 100 W Surround L/R 100 W + 100 W (8 Ω , 20 Hz~20 kHz, FTC) Dynamic Power: 230 W + 230 W (3 Ω , Front) 170 W + 170 W (4 Ω , Front) 115 W + 115 W (8 Ω , Front) THD (Total Harmonic Distortion): 0.08 % (Power Rated) Damping Factor: 60 (Front, 1 kHz, 8 Ω ) Input ...

  • Onkyo HT-R8230 - page 38

    38 Memo ...

  • Onkyo HT-R8230 - page 39

    39 Memo ...

  • Onkyo HT-R8230 - page 40

    SN 29343866 D0406-1 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzel ...

メーカー Onkyo カテゴリー Stereo Receiver

Onkyo HT-R8230のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HT-R8230の取扱説明書
- Onkyoの製品カード
- パンフレット
- またはOnkyo HT-R8230の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Onkyo HT-R8230の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Onkyo HT-R8230の取り付け説明書、サービスマニュアル、簡易説明書、またはOnkyo HT-R8230のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Onkyo HT-R8230の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Onkyo HT-R8230デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがOnkyo HT-R8230を使用するのを助ける技術的文書のことです。説明書は通常、全てのOnkyo HT-R8230ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Onkyoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Onkyo HT-R8230の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははOnkyo HT-R8230の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Onkyo HT-R8230に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Onkyo HT-R8230デバイスの基本機能を使うにあたってのヒント。 Onkyo HT-R8230のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Onkyo HT-R8230に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるOnkyo HT-R8230のメーカー/サービスへの連絡先に関する情報。

Onkyo HT-R8230についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもOnkyo HT-R8230の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがOnkyo HT-R8230で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)