Milnor K36 0005の取扱説明書

21ページ 0.52 mb
ダウンロード

ページに移動 of 21

Summary
  • Milnor K36 0005 - page 1

    Published Manual Number/ECN: H28 0010/2001074N • Publishing System: TPAS • Access date: 2/14/01 • Document ECN's: Latest Available Kit Instruction— K28 0010 K36 0005 K36 0005R PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A. ...

  • Milnor K36 0005 - page 2

    Please Read A bout the Manual Identif y ing Information on the Cover The front cover d isplay s pert inent id entify ing in form ation fo r this m anual. M ost im porta nt, are the publishe d m anual number ( part num ber) /ECN (date code). Ge nerally , when a r eplacem ent manual is furnish ed, it w ill hav e the sam e publis hed m anual num ber, ...

  • Milnor K36 0005 - page 3

    1 ...

  • Milnor K36 0005 - page 4

    MSSM020 4AE/833 2BV (1 of 1) È V-BELT TENSION ADJUSTMENTS FOR 30" AND 36" B-TYPE MACHINES AND 42" Q-TYPE MACHINES This instruction i s to be used for adjus ting the belt tension on the fol lowing machine modes: 30016BWE 42026QHE 36021BWE 42026QTG 360326QWE 42026QTH 42026QWE A belt tension t esting devi ce (Milnor ® part num ber 30T ...

  • Milnor K36 0005 - page 5

    MSSM0301AE/9126B V È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions. Ê Tension Settings Set the o-rings on the tension testing device (FIGURE 1) as f ...

  • Milnor K36 0005 - page 6

    MSSM0301AE/9126BV (1 of 1) È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions. Ê Tension Settings Set the o-rings on the tension testing device (FIGURE ...

  • Milnor K36 0005 - page 7

    M S S M A40 5 A E / 873 7 B V È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the following machine models: 48032BHE 48032BTG 48032BTH 48036QHE 48036QTG 48036QTH 52038WE1 52038WTF 52038WTB 52038WTG 52038WTH 60036WE2 60036WE3 60036SG2 60036 ...

  • Milnor K36 0005 - page 8

    MS SMA405 AE/ 8737 BV (1 of 2) È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the following machine models: 48032BHE 48032BTG 48032BTH 48036QHE 48036QTG 48036QTH 52038WE1 52038WTF 52038WTB 52038WTG 52038WTH 60036WE2 60036WE3 60036SG2 6003 ...

  • Milnor K36 0005 - page 9

    Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.6 - 9.2 KP3 5.1 - 7.1 KN 5/16 5.7 - 7.6 JP3 4.4 - 5.9 JN DRAIN 5/32 5.7 - 7.6 JP3 4.4 ...

  • Milnor K36 0005 - page 10

    Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.6 - 9.2 KP3 5.1 - 7.1 KN 5/16 5.7 - 7.6 JP3 4.4 - 5.9 JN DRAIN 5/32 5.7 - 7.6 JP3 4.4 ...

  • Milnor K36 0005 - page 11

    9 ...

  • Milnor K36 0005 - page 12

    M S S M 030 3 A E / 845 1 B V È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.). It does not apply to jackshaft bearings , i dler shaft bear ings or bearings on open pocket machines ...

  • Milnor K36 0005 - page 13

    MSSM 0303 AE/8451 BV (1 of 5) È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.). It does not apply to jackshaft bearings , i dler shaft bear ings or bearings on open pocket machines ...

  • Milnor K36 0005 - page 14

    inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support. 4. Slide the bearing off of the shaft and if it is to be reused, place it on a clean surface and cover with a clean, ...

  • Milnor K36 0005 - page 15

    inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support. 4. Slide the bearing off of the shaft and if it is to be reused, place it on a clean surface and cover with a clean, ...

  • Milnor K36 0005 - page 16

    Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked. Remove the o-rings from the i ...

  • Milnor K36 0005 - page 17

    Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked. Remove the o-rings from the i ...

  • Milnor K36 0005 - page 18

    Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled. It is of critical importance w ...

  • Milnor K36 0005 - page 19

    Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled. It is of critical importance w ...

  • Milnor K36 0005 - page 20

    Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s). Use a hammer and a metal drift as shown in FIGURE 11, to tighten the locknut. It is imp erative to only tap lightly and to assure that metal chips from the drift or locknut do not fa ...

  • Milnor K36 0005 - page 21

    Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s). Use a hammer and a metal drift as shown in FIGURE 11, to tighten the locknut. It is imp erative to only tap lightly and to assure that metal chips from the drift or locknut do not fa ...

メーカー Milnor カテゴリー Washer

Milnor K36 0005のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- K36 0005の取扱説明書
- Milnorの製品カード
- パンフレット
- またはMilnor K36 0005の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Milnor K36 0005の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Milnor K36 0005の取り付け説明書、サービスマニュアル、簡易説明書、またはMilnor K36 0005のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Milnor K36 0005の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Milnor K36 0005デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMilnor K36 0005を使用するのを助ける技術的文書のことです。説明書は通常、全てのMilnor K36 0005ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Milnorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Milnor K36 0005の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMilnor K36 0005の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Milnor K36 0005に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Milnor K36 0005デバイスの基本機能を使うにあたってのヒント。 Milnor K36 0005のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Milnor K36 0005に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMilnor K36 0005のメーカー/サービスへの連絡先に関する情報。

Milnor K36 0005についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMilnor K36 0005の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMilnor K36 0005で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)