-
Delta 34-555 - page 1
INSTRUCTION MANUAL Sliding T able Attachment (Model 34-555) P ART NO. 1346924 - 09-18-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...
-
Delta 34-555 - page 2
2 W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precautions ar e overlooked ...
-
Delta 34-555 - page 3
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUCT - TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment sh ...
-
Delta 34-555 - page 4
4 FOREWORD Delta Model 34-555 Sliding T able Attachment is an accessory for providing support for large capacity wood-working operations. The fence can be positioned in the front or r ear of the movable table and can be positioned to make miter cuts. The adjustable stock stop is excellent for repetitive cutting. FUNCTIONAL DESCRIPTION UNP ACKING AN ...
-
Delta 34-555 - page 5
5 ASSEMBL Y If your saw is equipped with the Delta Jet-Lock Rip Fence with round guide rails, cut 5-1/2" of f of the left end of both the front and r ear guide rails. If your saw is equipped with a Beisemeyer fence, measur e 1-1/2" to the left from the left side of the table and cut the rail. If your saw is equipped with the Delta Unifenc ...
-
Delta 34-555 - page 6
6 FOR 10" CONTRACTOR’S SA WS (CURRENT STYLE) Fig. 9 Fig. 10 1. If your switch is attached to the left extension wing, remove it. (After installation of the sliding table, r e-attach the switch to the location shown in Fig. 9.) 2. Remove the left-hand table extension. (It will not be used with the Sliding T able.) 3. Confirm that the rail/bra ...
-
Delta 34-555 - page 7
7 Fig. 15 Fig. 16 FOR 10" TIL TING ARBOR SA WS ONL Y 1. Remove the motor cover . (T o use the Sliding table, replace the motor cover with the part #734557 Hinged Motor Cover . Refer to the instructions that accompany the cover for installation.) 2. Locate the rail (Fig.15), two 1" hex head screws, 2 flat washers, 2 special washers, and 2 ...
-
Delta 34-555 - page 8
1. Attach the upper rail assembly (L) Fig. 27 to the side of the table where the extension wing was pr eviously mounted, using the three 2-1/2" socket head scr ews (M) and lockwashers (N) thr ough the holes (C) Fig. 28. 2. Use a square (D) Fig. 28 with a straight edge (A) on the machine table with the other end extending over the top of the up ...
-
Delta 34-555 - page 9
9 9 Fig. 27 Fig. 28 Fig. 29 Fig. 30 Fig. 31 L M N C E B D A R Q Q P S P W U T S V Fig. 32 Fig. 33 Fig. 34 P S X S E Z A Y F Fig. 35 Fig. 36 E F B D C C H G Fig. 37 F Y J Fig. 38 K M L For Old Contractor’ s Saws, turn bracket (A) Fig. 34 upside down so that the bearing (Y) contacts the rail (F). 10. Adjust the two lower bearings, one of which is s ...
-
Delta 34-555 - page 10
10 Fig. 43 Fig. 44 F G H F G Fig. 39 Fig. 40 Fig. 41 Fig. 42 N P R V S N P R X Y W C D E C E NOTE: Never operate the sliding table with the table lock/stop bracket removed. 15. Place the special thr eaded bolt (N) Fig. 39 thr ough the hole in the slide bracket (P) and the spacer and flat washer (R), then through the bushing (S) in the table and fra ...
-
Delta 34-555 - page 11
11 H C A B Fig. 50 Fig. 51 Fig. 52 Fig. 53 Fig. 54 A B C A B C F G E D K F G E H J M L ADJUSTING HEIGHT OF RIGHT EDGE OF SLIDING T ABLE L The right edge of the sliding table should be slightly higher than the machine table, both front and r ear . T o check and adjust: 1. Use the fence (A) Figs. 49 and 50 or a suitable straight edge to see if the sl ...
-
Delta 34-555 - page 12
Adjust the sliding table so that it is parallel with the machine table. (The sliding table must also be slightly higher than the machine table.) T o check and adjust: Fig. 56 Fig. 57 A B C E F D ADJUSTING SLIDING T ABLE P ARALLEL WITH MACHINE T ABLE L 12 1. Place a straight edge or the fence (A) Fig. 56 over the sliding table (B) and machine table ...
-
Delta 34-555 - page 13
13 Fig. 66 Fig. 64 Fig. 65 A Fig. 58 Fig. 59 A Fig. 60 Fig. 61 Fig. 62 Fig. 63 B B E C D A G F H Fig. 67 K L J N M ...
-
Delta 34-555 - page 14
14 14 Fig. 68 1. Loosen the clamp handle (A) and the clamp knob (D) Fig. 68. Slide the fence (C) Fig. 68 from the two fence clamps (B). 2. Remove the fence locking handle, the clamp knob, and the fence clamps (B) and re-position the fence clamps (B), clamp handle, and clamp knob to the rear of the sliding table (Fig. 68). 3. Slide the fence (C) Fig ...
-
Delta 34-555 - page 15
15 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standar ds and are serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality pr oduct or to obtain parts, service, warr ...
-
Delta 34-555 - page 16
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...
Delta 34-555についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもDelta 34-555の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 34-555で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。