Harbor Freight Tools 95346の取扱説明書

19ページ 1.52 mb
ダウンロード

ページに移動 of 19

Summary
  • Harbor Freight Tools 95346 - page 1

    GASOLINE AUGER DRILL 1.5 HP Model 95346 ASSEMBL Y AND OPERA TION INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. CAUTION! Y our W arranty Is V oided If: Y ou do not operate the Auger Drill with the proper 25:1 unleaded fuel/2-cycle oil mix in its fuel tank. Do not run the Engine wit ...

  • Harbor Freight Tools 95346 - page 2

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 2 REV 07b, 07e SPECIFICA TIONS Engine Specications 1.5 HP / 52cc / Single Cylinder / 2-Stroke / Recoil Start Fuel Required 25:1 Unleaded Gasoline (89 octane or better) & 2 Cycle Oil Mixture Fuel T ank Capacity 0.26 Gallon Recommended Gear Oil SAE 80 – 90 Weight Gear Oil Ro ...

  • Harbor Freight Tools 95346 - page 3

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 3 GENERAL SAFETY RULES AND PRECAUTIONS W ARNING! READ AND UNDERST AND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, re, and/or serious injury . SA VE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit. 1. Cluttere ...

  • Harbor Freight Tools 95346 - page 4

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 4 Do not use the Auger Drill if the Kill Switch does not turn it off. 2. Any tool that cannot be controlled with its Kill Switch is dangerous and must be replaced. Store idle tools out of reach of children and other untrained persons. 3. T ools are dangerous in the hands of untrain ...

  • Harbor Freight Tools 95346 - page 5

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 5 Do not leave the Auger Drill unattended when it is running. 4. T urn off the Engine before leaving. Do not allow children and other unauthorized people to handle or play with 5. the Auger Drill. Do not leave the drill unattended in an area accessible to children. Maintain a rm ...

  • Harbor Freight Tools 95346 - page 6

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 6 When spills of fuel or oil occur , they must be cleaned up immediately . 3. Dis- pose of uids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container . Do not store fuel or other ammable materials near th ...

  • Harbor Freight Tools 95346 - page 7

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 7 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 14, 16, and 18 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y FIGURE A ...

  • Harbor Freight Tools 95346 - page 8

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 8 PRE-ST ART INSTRUCTIONS Fill the Fuel T ank IMPORT ANT! 1. Y our warranty is voided if you do not operate the Auger Drill with the proper 25:1 fuel mix in its Fuel T ank (89). Do not run the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper ...

  • Harbor Freight Tools 95346 - page 9

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 9 OPERA TION Starting and Stopping 1. W ARNING! Always wear safety equipment. When operating the Auger Drill, wear ANSI-approved safety impact eye goggles, hearing protection, heavy duty work gloves, sturdy work boots, and head protection. Place the Auger Drill on its side with its ...

  • Harbor Freight Tools 95346 - page 10

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 10 6. W ARNING! The Auger (33a) should do not turn at idle. If it is turning at idle, turn the Idle Screw of the Carburetor (shown right) counterclock - wise to reduce the idle RPM and stop the Auger , or imme- diately discontinue using the Auger Drill and contact a quali- e d s ...

  • Harbor Freight Tools 95346 - page 11

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 1 1 Drilling a Hole Stand with a solid stance on stable 1. gro und . B rac e your sel f and mai nta in a proper grip with both hands on the Frame (1b) whenever the Engine is running. (See Figure E.) Accelerate the Engine to full throttle 2. just before starting to drill by squeez - ...

  • Harbor Freight Tools 95346 - page 12

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 12 INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Re mo ve the Spa rk Plu g (51 ) an d al low the eng in e to co ol com pl et ely prior to performing any service, maintenance, or cleaning of the Auger Drill. Before each use: 2. Inspect the general condition of the Auger Drill. ...

  • Harbor Freight Tools 95346 - page 13

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 13 TROUBLESHOOTING Problem Possible Cause Possible Solution Engine will not start. Low or no fuel in fuel tank or 1. improper fuel/2-cycle oil mix. Not enough fuel getting to 2. carburetor . Faulty spark plug. 3. Contaminated fuel. 4. Insufcient electrical current 5. getting to ...

  • Harbor Freight Tools 95346 - page 14

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 14 P ARTS LIST - ENGINE Part Description Qty . 1 Set Screw (M5 x 12) 1 2 Gasket 1 3 Reel 1 4 Starter Rope 1 5 Spiral Spring 1 6 Rewind Starter Assy . 1 7 Starter Handle 1 8 Handle Clip 1 9 Screw (M5 x 20) 6 10 Crankcase Gasket 1 11 Nut (M8) 1 12 Startup Claw 1 13 Startup Reed 1 14 ...

  • Harbor Freight Tools 95346 - page 15

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 15 ASSEMBL Y DIAGRAM - ENGINE ...

  • Harbor Freight Tools 95346 - page 16

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 16 P ARTS LIST - GEARBOX UNIT REV 07b Part Description Qty . 1a Starting Flange 1 2a Oil Seal (20 x 52 x 7) 1 3a W asher 1 4a W asher 1 5a Fender Ring (47) 1 6a Bearing (6204) 1 7a Worm Gear 1 8a Gearbox 1 9a Hex Head Screw (M6 x 25) 4 10a Stud (M6) 4 1 1a Nut (M6) 4 12a W asher 1 ...

  • Harbor Freight Tools 95346 - page 17

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 17 P ARTS LIST & ASSEMBL Y DIAGRAM - FRAME Part Description Qty . 1b Frame (Complete) 1 2b Handle 1 3b T ie Strip 3 4b Handle 1 5b Kill Switch 1 Part Description Qty . 6b Kill Switch Bracket 1 7b Screw (M12 x 20) 2 8b Accelerator Cable 1 9b Bushing 1 10b Speed Control 1 ...

  • Harbor Freight Tools 95346 - page 18

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 18 Emission Control System W arranty United States Emission Control Defects W arranty Statement The United States Environmental Protection Agency (herein EP A), and Harbor Freight T ools ® (herein HFT) are pleased to explain the emission control system warranty on your 1995 and la ...

  • Harbor Freight Tools 95346 - page 19

    SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 19 5. Service and Maintenance Component parts which are not scheduled for replacement as required maintenance or are scheduled only for regular inspection to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part which is schedu ...

メーカー Harbor Freight Tools カテゴリー Cordless Drill

Harbor Freight Tools 95346のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 95346の取扱説明書
- Harbor Freight Toolsの製品カード
- パンフレット
- またはHarbor Freight Tools 95346の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Harbor Freight Tools 95346の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Harbor Freight Tools 95346の取り付け説明書、サービスマニュアル、簡易説明書、またはHarbor Freight Tools 95346のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Harbor Freight Tools 95346の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Harbor Freight Tools 95346デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHarbor Freight Tools 95346を使用するのを助ける技術的文書のことです。説明書は通常、全てのHarbor Freight Tools 95346ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Harbor Freight Toolsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Harbor Freight Tools 95346の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHarbor Freight Tools 95346の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Harbor Freight Tools 95346に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Harbor Freight Tools 95346デバイスの基本機能を使うにあたってのヒント。 Harbor Freight Tools 95346のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Harbor Freight Tools 95346に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHarbor Freight Tools 95346のメーカー/サービスへの連絡先に関する情報。

Harbor Freight Tools 95346についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHarbor Freight Tools 95346の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 95346で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)