Vision Fitness ST200の取扱説明書

20ページ 3.48 mb
ダウンロード

ページに移動 of 20

Summary
  • Vision Fitness ST200 - page 1

    Assembly Guide ST200 FUNCTIONAL TRAINER ...

  • Vision Fitness ST200 - page 2

    2 T o avoid possible damage to this Functional T rainer , please follow these assembly steps in the correct order . Before proceeding, find your new Functional T rainer serial number located on the back of the rear floor suppor t (1a), and enter here: Refer to this number when calling for ser vice, and enter this serial number on your W arranty Car ...

  • Vision Fitness ST200 - page 3

    3 2 STEP 1 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 9 STEP ...

  • Vision Fitness ST200 - page 4

    4 19mm Wrench 6mm L-Shaped Wrench TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench ...

  • Vision Fitness ST200 - page 5

    5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 4 10.5 x 18 x 2T Flat W asher Quantity: 8 M10 x 1.5P Nut Quantity: 6 M10 x 1.5P x 60L Bolt Quantity: 4 M10 x 1.5P x 25L Bolt Quantity: 2 M6 x 1P x 15L Bolt Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P Nut Quantity: 2 10.5 x 30 x 2T Flat W asher Quanti ...

  • Vision Fitness ST200 - page 6

    6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P x 25L Bolt Quantity: 8 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 6 10.5 x 18 x 2T Flat W asher Quantity: 4 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P Nut Quantity: 4 10 x 30 x 2T Flat W asher ...

  • Vision Fitness ST200 - page 7

    7 BLACK BAG YELLOW BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 6 M10 x 1.5P Nut Quantity: 4 M10 x 1.5P x 60L Bolt Quantity: 2 M6 x 1P x 50L Bolt Quantity: 2 M12 Slotted Bolt Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 2 M6 x 1P Nut Quantity: 2 Karabiner Quantity: 5 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 2 SW6.1 x 12.2 x ...

  • Vision Fitness ST200 - page 8

    8 RED BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 10 M10 x 1.5P x 25L Bolt Quantity: 10 ...

  • Vision Fitness ST200 - page 9

    9 1d 1b 1e 1c 1a 1 STEP • Lay the back side of the rear vertical upright (1a) down onto the floor . The threaded bolt ends will be pointing up. Place the center floor support (1b) over the threaded ends. Attach a flat (10.5x18x2T) and spring (SW10.2x18.4x2.5T) washer and nut (M10x1.5P) to each end. Tip upright. Tighten fasteners using a 17mm wren ...

  • Vision Fitness ST200 - page 10

    10 2 STEP • Thread pull pins par tially onto 2a (Qty . 1) and 2c (Qty . 2). • Lay the front center vertical (2f) on the floor . Slide the seat suppor t structure (2a) over the open end of 2f. NOTE: Y ou must pull the pull pin out (2b) and hold it when sliding over 2f. Release and engage the pull pin in one of the lower holes of 2f. • Slide th ...

  • Vision Fitness ST200 - page 11

    11 3 STEP • Place the top front structure (3a) on top of 2f and attach with two bolts (M10x1.5Px60L), two flat (10.5x18x2T) washers, and two nuts (M10x1.5P). Tighten fasteners with a 6mm L-shaped wrench and a 17mm wrench. • Attach the seat (3b) up through the bottom of 2a with four bolts (M10x1.5Px25L). Attach the seatback (3c) through 2c with ...

  • Vision Fitness ST200 - page 12

    12 4 STEP • Place the bottom of the left oval upright (4a) onto the protruding bolts of 1d. NOTE: Make sure the 27 holes of 4a are on the outside. Mate the hole in the top of 4a with the top hole of 3a. Attach and tighten one flat (10x30x2T) & spring (SW10.2x18.4x2.5T) wa sh er and one bolt (M10x1.5Px60L). Tighten with a 6mm L-shaped wrench. ...

  • Vision Fitness ST200 - page 13

    13 5 STEP • If you are adding 15 weight plates to the base unit, proceed as follows. If you are adding 20 weight plates, the steel tube spacer (5a) will not be used. • Place two rubber weight plate bumpers (5b) over the 0.75” holes of 5a. Place 5a over the holes of 1b. With the horizontal holes at the bottom, place the two guide rods (5c) ove ...

  • Vision Fitness ST200 - page 14

    14 6 STEP Wrap one end of cable #1 around pulley A. On the right side of the unit, place it through pulleys B, C, D of 6a, and E. Remove the nuts from 2 slotted bolts (M12) (see diagram below). With the threads pointing down on the slotted bolt (M12), slide the end of cable #1 through it. Reattach the nuts on the slotted bolt. Attach it to one side ...

  • Vision Fitness ST200 - page 15

    15 7 STEP If assembling just the base unit ( ST200 ), proceed as follows. If assembling with the leg press ( ST250 ), refer to Step 5 of the leg press assembly guide. Slide the small steel end of cable #2 through pulleys F and G. Remove the nuts from the slotted bolt (M12). Slide the cable through the slotted bolt (M12). Reattach the nuts to the sl ...

  • Vision Fitness ST200 - page 16

    16 8 STEP • Remove the slotted bolts (8a) located on the inside of the right and left handles of uprights 4a & 4b. Remove the nuts from the bolts. Slide the small steel end of cable #3 through pulleys H & I. Continue through pulleys J thru P . Slide the cable through the slotted bolt so that the end pro- trudes out the bottom of the bolt. ...

  • Vision Fitness ST200 - page 17

    17 9 STEP • Place the rear hole of the left decorative cover (9a) over the threaded post on the left side of structure 5e. Loosely attach a spring (SW10.2x18.4x2.5T) washer and a bolt (M10x1.5Px25L). Thread two bolts (M10x1.5Px25L) and two spring (SW10.2x18.4x2.5T) washers into the two front holes. Tighten all bolts with a 6mm L-shaped wrench. Re ...

  • Vision Fitness ST200 - page 18

    18 General Warning/Safet y Decal Placement Weight Plate Sticker Placement 10 STEP • Attach the decals according to the diagram below . DECALS ...

  • Vision Fitness ST200 - page 19

    19 ...

  • Vision Fitness ST200 - page 20

    500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness. All Rights Reserved. 10.05 AG18.37PRD REV2 starts vision with a it all ...

メーカー Vision Fitness カテゴリー Home Gym

Vision Fitness ST200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ST200の取扱説明書
- Vision Fitnessの製品カード
- パンフレット
- またはVision Fitness ST200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Vision Fitness ST200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Vision Fitness ST200の取り付け説明書、サービスマニュアル、簡易説明書、またはVision Fitness ST200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Vision Fitness ST200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Vision Fitness ST200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVision Fitness ST200を使用するのを助ける技術的文書のことです。説明書は通常、全てのVision Fitness ST200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vision Fitnessの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Vision Fitness ST200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVision Fitness ST200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Vision Fitness ST200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Vision Fitness ST200デバイスの基本機能を使うにあたってのヒント。 Vision Fitness ST200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Vision Fitness ST200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVision Fitness ST200のメーカー/サービスへの連絡先に関する情報。

Vision Fitness ST200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもVision Fitness ST200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVision Fitness ST200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)