Cisco BayTech DS Seriesの取扱説明書

29ページ 0.76 mb
ダウンロード

ページに移動 of 29

Summary
  • Cisco BayTech DS Series - page 1

    DS Series Manual DATA SWITCH DS71-MD4 Host-Modem Module BayTech Manual Publication Revision May 2008 ...

  • Cisco BayTech DS Series - page 2

    Copyright 2007 by Bay Technical Associates, Inc. BayTech, is a registered trademarks of Bay Technical Associates, Inc. Windows 2000®, Windows XP® are products and reg istered trademark of Microsoft Corporation. Tera Term is a product and registered trademark of Vector, I nc. ...

  • Cisco BayTech DS Series - page 3

    DS71-MD4 Serial host and 56k Modem 3 ABOUT THIS OWNER’S MANUAL .......................................................................................................... 4 Connection Description ......................................................................................................... ................ 4 EIA-232 SERIAL CONNECTION... ...

  • Cisco BayTech DS Series - page 4

    DS71-MD4 Serial host and 56k Modem 4 ABOUT THIS OWNER’S MANUAL This document provides information required for installing and operating your Bay Tech equipment. It should allow the user to connect to, power up, and access an applications m enu where peripheral equipment can be controlled. We recommend readi ng this m anual carefully, while placin ...

  • Cisco BayTech DS Series - page 5

    DS71-MD4 Serial host and 56k Modem 5 EIA-232 SERIAL CONNECTION The DS-Series host communications modules have an RJ-45 port which uses an 8-pin crossed modular cable to connect to a local EIA-232 de vice such as a computer terminal or external m odem. Most serial computers do not have RJ-45 connections; therefore an ad apter is provided with this u ...

  • Cisco BayTech DS Series - page 6

    DS71-MD4 Serial host and 56k Modem 6 Power CAUTION: This unit is intended for indoor use only. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil the pow er cord when in use. Do not use extension cords. Do not attempt to make any internal changes to th e power source. Do not attem pt to modify any portio ...

  • Cisco BayTech DS Series - page 7

    DS71-MD4 Serial host and 56k Modem 7 • Connect the Host Module’s EIA- 232 port to the adapter via the RJ08X007 rolled flat ribbon cable. • Default configuration is 9600 bps, 8 data bits, 1 stop bit and no parity . NOTE: At any time during the session you n eed to go to another menu, use the Attention Character = semi-colon (;) . Press the att ...

  • Cisco BayTech DS Series - page 8

    DS71-MD4 Serial host and 56k Modem 8 Figure 2 Login Setup This menu allows the user to enable or disab le th e Header, Access Control, Menu, Manage Users, Auto Connect, Dial Back Number, and Assign User Ports. Figure 3 Header This allows the admin to have enable or di sable Header upon connect ion to the host module. Access Control This security fe ...

  • Cisco BayTech DS Series - page 9

    DS71-MD4 Serial host and 56k Modem 9 Manage Users This option allows the administrator to change u ser passwords or add/delete ne w users. Up to 19 users plus an administrator allowed. Usernam es are case sensitive and alphanumeric. Figure 4 Auto Connect This feature allows the admin to se lect the module and port th at the user will be automatical ...

  • Cisco BayTech DS Series - page 10

    DS71-MD4 Serial host and 56k Modem 10 Local Modem Option Figure 5 Ring to Answer This option sets the number of rings before the unit answers. Connectivity Timeout This option sets the continuous c onnectivity time (5 to 255 minutes) before the modem automatically disconnects. Inactivity Timeout This option sets the time the modem will automatical ...

  • Cisco BayTech DS Series - page 11

    DS71-MD4 Serial host and 56k Modem 11 Adapters Signals Listed are the pin specifications for the BayTech cable a nd adapters and the term inal COM ports: Signal RS-232 Port (DS) RS-232 Port (RPC) COM Port DE-9 Pin COM Port DB-25 Pin Signal DTR 1 1 4 20 DSR GND 2 2 1 GND RTS 3 3 7 5 CTS TXD 4 4 3 2 RXD RXD 5 5 2 3 TXD DSR 6 N/C 6 6 DTR GND 7 7 5 7 G ...

  • Cisco BayTech DS Series - page 12

    DS71-MD4 Serial host and 56k Modem 12 RJ08X007 Figures 1 and 2 provide vi sual representation of an RJ-45 receptacle and plug. ...

  • Cisco BayTech DS Series - page 13

    DS71-MD4 Serial host and 56k Modem 13 Det ailed Operation and Configuration DS71-MD4 Main Menu The menu may vary according to th e number of DS74 modules instal led in the unit. With a proper connection to the unit upon power-up or unit reset, the following menu is displayed: NOTE: Only the Admin user will see the Configur ation, Unit Reset, and I/ ...

  • Cisco BayTech DS Series - page 14

    DS71-MD4 Serial host and 56k Modem 14 Configuration Status The Status menu displays the modules installed and the current configuration of the host m odule. The following are the factory default settings: Copyright(C) Bay Technical Associates 2006 DS71-MD4 Data Switch Series - V90 Modem Host Module Revision F.1.01.01 Module 2 Status ............... ...

  • Cisco BayTech DS Series - page 15

    DS71-MD4 Serial host and 56k Modem 15 Installed Modules :2,3,5 Port Select Code ......................$BT Attention Character ...................; Disconnect Time Guard .................Disabled Port ID Echo ..........................Disabled Unit ID ...............................DS71-MD4 Local Modem Option: Rings to Auto-Answer................... ...

  • Cisco BayTech DS Series - page 16

    DS71-MD4 Serial host and 56k Modem 16 Serial Port Configuration Handshaking, Baud Rate, Word Size, Stop Bits, and Pa rity are configured through either the serial or Ethernet ports using the menus. Xon/Xoff, RTS and DTR Line Driver s can only be configured through the phone line via a modem. The default s ettings are 9600bps, 8 data bits, no parity ...

  • Cisco BayTech DS Series - page 17

    DS71-MD4 Serial host and 56k Modem 17 Stop Bits The Stop Bits are used to signal th e end of communication for a single packet. Since the data is clocked across the lines and each device has its own clock, it is possib le for the two devices to become slightly out of sync. Therefore, the stop bits not only indicate the end of transmission but also ...

  • Cisco BayTech DS Series - page 18

    DS71-MD4 Serial host and 56k Modem 18 RTS/DTR Line Driver Inactivity State RTS (Request to Send)/ DTR (Data Terminal Ready) is normally used in conj unction with an external modem. With no modem the RTS and DTS default state is High. Select “RTS Driver State” the DS displays the f ollowing: Select “DTR Driver State” th e DS displays the fol ...

  • Cisco BayTech DS Series - page 19

    DS71-MD4 Serial host and 56k Modem 19 Disconnect Timeguard This feature ensures reliable binary data transm ission by providing a one-second “Timeguard” after the DS-Series receives the attention char acter. If m ore data is received within the delay period, the DS treats the character as da ta, not an attention charac ter; thereby preventing u ...

  • Cisco BayTech DS Series - page 20

    DS71-MD4 Serial host and 56k Modem 20 Header If enabled, the following header appears with th e m ain menu upon initializati on of power or after a modem connection to the host module ha s been established. If disabled, the header does not appear with the main menu. Default Header is e nabled . Access Control This feature configures the Serial and ...

  • Cisco BayTech DS Series - page 21

    DS71-MD4 Serial host and 56k Modem 21 Change User’s Password NOTE: The factory default password for “admin” is <cr> ( Enter ). The admin can change a current user’s port access and password. Select the num ber of the user from the User Management Menu and the Host Module displays the following: ADD User Select A), from the User Manage ...

  • Cisco BayTech DS Series - page 22

    DS71-MD4 Serial host and 56k Modem 22 Auto Connect This feature allows the admin to select the module a nd port that the user will b e automatically connected on dial-in. The auto connect port ha s priority over the login setup m e nu enable/disable selection, thus prevent the menu selection screen from app earin g at the initial login sequence. Se ...

  • Cisco BayTech DS Series - page 23

    DS71-MD4 Serial host and 56k Modem 23 Select “Dialback Delay” option to set the amount of delay time before the unit dials the phone number assigned to the user. Default is 10 seconds Assign User Ports This option allows the administra tor to limit users’ port acces s. Add ports Module displays the user’s assigned ports: Remove Ports Select ...

  • Cisco BayTech DS Series - page 24

    DS71-MD4 Serial host and 56k Modem 24 Select this option to add all port s to the user. The module displays the user with all ports added. Remove All Ports Select this option and the module displa ys the user with all ports deleted. Local Modem Option Ring to Answer Select “Rings to Auto Answer” to set the number of rings before the unit answer ...

  • Cisco BayTech DS Series - page 25

    DS71-MD4 Serial host and 56k Modem 25 Unit ID This option allows the admin users to change the Host Module’s name. Enter the desired Unit ID, followed by <cr.> The DS 71-MD4 stores the changes in non-volatile memory and returns to the module configuration menu. I/O modules Reset Select “I/O Modules Reset” followed by <cr>. The m o ...

  • Cisco BayTech DS Series - page 26

    DS71-MD4 Serial host and 56k Modem 26 b. Verify computer serial port configuration; 9600, 8, none, 1 , c. Verify the cable and adapter has the co rrect pin out, RJ08X007 and 9FRJ45PC-1. d. Cisco Rollover cables have the same pin out as RJ08X007. e. Type 5(;), the Attention Character will not ec ho to the scr een, if it does than it may have been ch ...

  • Cisco BayTech DS Series - page 27

    DS71-MD4 Serial host and 56k Modem 27 DS71-MD4 Reset Procedure 1. Press and hold reset button as you power cycle the module. 2. Continue to hold button for 45 seconds, then release button. 3. Use Terminal program into the serial port if not already doing so. 4. If no opening menu, Type 5 semi-colons. 5. If appears not to work repeat reset procedure ...

  • Cisco BayTech DS Series - page 28

    DS71-MD4 Serial host and 56k Modem 28 Exceptions This warranty does not cover misuse or minor imperfections that fall within design specifications or that do not materially alter functionality. BayTech does not warrant and is not responsible for damages incurred in shipping and handling or caused by disasters (such as fire, f lood, wind, earthquake ...

  • Cisco BayTech DS Series - page 29

    DS71-MD4 Serial host and 56k Modem 29 If a product is being returned for credit (based on BayTech approval), the credit will no t include shipping and handling charges. Determination of credit amount will be made after BayTech receives the product. Returns on BayTech products older than 3 months are subject to a 15% re-stocking fee of the list pric ...

メーカー Cisco カテゴリー Switch

Cisco BayTech DS Seriesのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BayTech DS Seriesの取扱説明書
- Ciscoの製品カード
- パンフレット
- またはCisco BayTech DS Seriesの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco BayTech DS Seriesの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco BayTech DS Seriesの取り付け説明書、サービスマニュアル、簡易説明書、またはCisco BayTech DS Seriesのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco BayTech DS Seriesの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco BayTech DS Seriesデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco BayTech DS Seriesを使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco BayTech DS Seriesユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ciscoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco BayTech DS Seriesの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco BayTech DS Seriesの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco BayTech DS Seriesに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco BayTech DS Seriesデバイスの基本機能を使うにあたってのヒント。 Cisco BayTech DS Seriesのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco BayTech DS Seriesに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco BayTech DS Seriesのメーカー/サービスへの連絡先に関する情報。

Cisco BayTech DS Seriesについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco BayTech DS Seriesの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco BayTech DS Seriesで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)